WAGO 750-1416/040-000 User manual

Pos: 2/ D oku me ntati on allg em ein /Ei nb and /Ei nb and Fro nts eite -H andb uch; CI 20 17; mit Do cVaria blen (St andar d) @ 28\mod_1486477502910_0.docx@ 405388@ @ 1
Manual
WAGO I/O SYSTEM 750 XTR
750-1416/040-000
8DI 24 VDC 0.2ms 2
-wire XTR
8
-Channel Digital Input; 24 VDC; 0.2 ms;
2
-Conductor Connection; Extreme
Version 1.1.0
Pos: 3/ Al le Seri e n (A llg e mei n e M od ul e) /Rec htl ic h es, Allgemeines/ImpressumfürStandardhandbücher - allg . A ng a be n, Ansc hr i ft en, Telef onn u m mer n und E-M ail-A dr es s e n @ 3\mod_1219151118203_21.docx @ 21060@ @ 1

2 WAGO I/O SYSTEM 750 XTR
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
© 2020 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: www.wago.com
Technical Support
Phone: [phone] – 4 45 55
Fax: [phone] – 84 45 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
=== Ende d er List e f ür T e xt mar ke Ei nb a nd_ v orn e == =

WAGO I/O SYSTEM 750 XTR Table of Contents 3
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Pos: 5/ D ok ume nt ati on allg em ein /V erz eic h nis se /I nhal ts ver z eic hni s - Ü b ers chri f t oG und V erz ei ch nis @ 3\mod_1219151230875_21.docx@21063 @ @ 1
Table of Contents
1Notes about this Documentation .............................................................5
1.1 Validity of this Documentation.................................................................5
1.2 Copyright................................................................................................5
1.3 Symbols .................................................................................................6
1.4 Number Notation ....................................................................................7
1.5 Font Conventions ...................................................................................7
2Important Notes ........................................................................................8
2.1 Legal Bases............................................................................................8
2.1.1 Subject to Changes............................................................................8
2.1.2 Personnel Qualifications ....................................................................8
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions.......8
2.1.4 Technical Condition of Specified Devices...........................................9
2.1.4.1 Disposal ........................................................................................9
2.1.4.1.1 Electrical and Electronic Equipment..........................................9
2.1.4.1.2 Packaging ...............................................................................10
2.2 Safety Advice (Precautions) .................................................................11
3Device Description..................................................................................14
3.1 View .....................................................................................................16
3.2 Connectors...........................................................................................17
3.2.1 Data Contacts/Local Bus..................................................................17
3.2.2 Power Jumper Contacts/Field Supply ..............................................18
3.2.3 Push-in CAGE CLAMP®Connectors................................................19
3.3 Display Elements..................................................................................20
3.4 Operating Elements..............................................................................20
3.5 Schematic Diagram ..............................................................................21
3.6 Technical Data .....................................................................................22
3.6.1 Device Data .....................................................................................22
3.6.2 Power Supply...................................................................................22
3.6.3 Communication................................................................................22
3.6.4 Inputs...............................................................................................23
3.6.5 Connection Type..............................................................................23
3.6.6 Mechanical Conditions .....................................................................23
3.6.7 Climatic Environmental Conditions...................................................24
3.7 Approvals .............................................................................................25
3.8 Standards and Guidelines ....................................................................26
4Process Image.........................................................................................32
5Mounting..................................................................................................33
5.1 Mounting Sequence..............................................................................33
5.2 Inserting and Removing Devices ..........................................................34
5.2.1 Inserting the I/O Module...................................................................34
5.2.2 Removing the I/O Module ................................................................35
6Connect Devices .....................................................................................36
6.1 Connecting a Conductor to the Push-in CAGE CLAMP®......................36
6.2 Connection Example ............................................................................37

4 Table of Contents WAGO I/O SYSTEM 750 XTR
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
7Use in Hazardous Environments ...........................................................38
7.1 Marking Configuration Examples ..........................................................39
7.1.1 Marking for Europe According to ATEX and IECEx..........................39
7.1.2 Marking for the United States of America (NEC) and Canada
(CEC)...............................................................................................43
7.2 Installation Regulations.........................................................................46
7.2.1 Special Notes including Explosion Protection...................................46
7.2.2 Special Notes Regarding ANSI/ISA Ex ............................................48
List of Figures ..................................................................................................49
List of Tables....................................................................................................50
=== En de der Lis te für T extmar ke Verz eich nis_vor ne == =

WAGO I/O SYSTEM 750 XTR Notes about this Documentation 5
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Pos:7/Dokumentationallgemein/AnmerkungenzurBearbeitung/!! ! ! !! ! ! ! ! !! ! ! ! Dieses Dokument ist nichtfreigegeben! ! ! ! ! ! !! ! ! ! !! ! ! @ 7\mod_1271240183952_21.docx@ 55090@ @ 4
Pos: 8/ Al le Seri e n (A llg e mei n e M od ul e) /Üb ers c hri ft en/ Ebe n e 1/H in wei s e z u dies er D o ku ment ati on - Ü ber sc hr ift 1 @ 4\mod_1237987661750_21.docx @ 29029@ 1@ 1
1 Notes about this Documentation
Pos: 9/ All e S eri en (A llg em eine M od ul e)/Si cher h eits- unds onstige Hinweise/Hinweis/Hinweis:D okumentationaufbewahren@ 4\mod_1237987339812_21.docx@ 29026@ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
Pos: 10 /A ll e Seri en (Allg e mei n e M od ul e)/ Ü b ers chr if te n/ Eb e ne 2/G ülti g kei ts b erei c h - Ü ber s chr ift 2 @ 12\mod_1338912448776_21.docx@ 96469@ 2@ 1
1.1 Validity of this Documentation
Pos: 11 / S eri e 750 ( WA G O-I/ O-SYST EM )/H i nweis e z ur Do kume nt ati on ( al te Struk tur) / Gül tig keit sber ei ch/ Gül tig kei ts ber eic h D o ku ment ati on I/ O-Modul 750-xxxx, oh ne Vari anten angab e @ 14\mod_1358944037947_21.docx@ 109346@ @ 1
This documentation is only applicable to the I/O module 750-1416/040-000
(8DI 24 VDC 0.2ms 2-wire XTR).
Pos: 12 / S eri e 750 ( WA G O-I/ O-SYST EM ) /Hi n weis e z ur Do kum ent at i on ( al t e S tru k tur) /H i n weis e/ A c ht ung : H in w eis zur D o ku me nt ati o n I/ O-M od ul e 75 0- xxxx/040- 000 @ 27\mod_1468502299549_21.docx@216892@ @ 1
The I/O module 750-1416/040-000 shall only be installed and operated according
to the instructions in this manual, in the system description for the WAGO I/O
SYSTEM 750 XTR and in the manual for the used fieldbus coupler/controller.
Consider power layout of the WAGO I/O SYSTEM 750 XTR!
In addition to these operating instructions, you will also need the system
description “Design Notes XTR – Guidelines and Recommendations for
Increasing Operational Safety” and the manual for the used fieldbus
coupler/controller, which can be downloaded at www.wago.com. There, you can
obtain important information including information on electrical isolation, system
power and supply specifications.
Pos: 13.1 / All e Seri en ( All ge mei ne M od ule) /Ü bers chr ift e n/ Ebe ne 2/U r heb er sc hutz -Ü ber sc hri ft 2 @ 23\mod_1435647042188_21.docx @ 184808@ 2@ 1
1.2 Copyright
Pos: 13.2 / All e Seri en ( A llg e mei ne M o dul e)/R ec htl ich es , Al lg e mei nes /U rh eb ers c hutz aus führ li ch @ 4\mod_1235565145234_21.docx@ 27691@ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos:13.3/Dokumentationallgemein/Gl ie der ung s el e men te /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

6 Notes about this Documentation WAGO I/O SYSTEM 750 XTR
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Pos: 13.4 / All e Seri en ( All ge mei ne M od ule) /Ü bers chr ift e n/ Ebe ne 2/ S ymbol e - Ü b ers chr if t 2@ 13\mod_1351068042408_21.docx@ 105270@ 2 @ 1
1.3 Symbols
Pos: 13 .5.1 /Al le Seri e n ( Al lg e mei ne Mod ule) / Si ch erh ei ts- u nd sons ti g e H i n weis e/ G ef ahr /G ef a hr : _War nung vor Pers on en sc hä de n allg emei n _ - Er läu ter ung @ 13 \mod_1343309450020_21.docx@ 101029@ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 13 .5.2 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i nwei s e/G efa hr /G ef ahr : _ War nu ng vor P ers on en sch ä de n d urc h el e ktri sc he n St ro m_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101 030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 13 .5.3 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstige H i n weis e/ W ar nung / W ar nung : _W arn u ng vor P er so ne nsc h äd e n al lg em ei n_ - Erläuterung@ 13\mod_1343309877041_21.docx@ 101035@ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 13 .5.4 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i nwei s e/V orsi c ht /V orsi ch t: _War n ung vor Per s on ens c häd en allge m ein _ - Erläuterung @ 13\mod_1343310028762_21.docx@ 101038@ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 13 .5.5 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i nwei s e/A c htung / Ach tu ng : _ War nu ng vor Sachsc h äd en al lg em ein _ - Er lä ut er ung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 13 .5.6 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und sonstigeHi nweis e/ Ac ht ung / Ach tu ng: _War nu ng vor Sachsc h äd en d urc h elek tros t atis ch e Aufla du ng_ - Erl äut er ung @ 13\mod_1343310227702_21.docx@ 101044@ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 13 .5.7 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sonstige Hi nweise/Hinweis/Hinweis:_Wichtiger Hin weis allgemein_- Erläuterung @ 13\mod_1343310326906_21.docx@ 101047@ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 13 .5.8 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti g e H i n weis e/I nf or ma ti o n/I nf or ma ti on: _W eiter e I nf or ma ti on allg e mei n_ -Er l äu ter ung @ 13 \mod_1343310439814_21.docx@ 101051@ @ 1

WAGO I/O SYSTEM 750 XTR Notes about this Documentation 7
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos:13.6/Dokumentationall g e mei n/ Gli e der ung s el e men te /---Sei t e n wechs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1
Pos: 13.7 / All e Seri en ( All ge mei ne M od ule) /Ü bers chr ift e n/ Ebe ne 2/D ar st ell ung der Z a hle ns yst em e - Ü bers c hri ft 2 @ 23\mod_1435647128078_21.docx @ 184811@ 2@ 1
1.4 Number Notation
Pos: 13.8 / All e Seri en ( A llg e mei ne M o dul e)/R ec htl ich es , Al lg e mei nes /Z ahl e ns yst e me @ 3\mod_1221059454015_21.docx@ 21711@ @ 1
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
Pos: 13.9 / All e Seri en ( All ge mei ne M od ule) /Ü bers chr ift e n/ Ebe ne 2/ Sc hri ft ko nvent i one n - Ü ber sc hri ft 2 @ 23\mod_1435647186005_21.docx @ 184814@ 2@ 1
1.5 Font Conventions
Pos: 13.1 0 / Al le Ser ie n (Al l ge m ein e M o dul e)/ Re ch tl ic h es, Allg e mei n es/ Sc hr if t kon ve nti on en @ 3\mod_1221059521437_21.docx @ 21714@ @ 1
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.:
File
>
New
Input
Designation of input or optional fields are marked in bold letters,
e.g.:
Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.:
[F5]
Pos: 14 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\ mod_1221108045078_0.docx@ 21810 @ @ 1

8 Important Notes WAGO I/O SYSTEM 750 XTR
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Pos: 15 /Al l e S eri en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 1/ Wic hti ge Erl äu ter unge n - Ü ber sc hr ift 1 @ 4 \mod_1241428899156_21.docx@32170 @ 1 @ 1
2 Important Notes
Pos: 16.1 / All e Seri en ( All ge mei ne M od ule) /R ec htli ch es, Al lg em ei nes /Wi chti g e Er l äuter ung en - Einl eit u ng @ 3\mod_1221059818031_21.docx@ 21717@ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 16 .2 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte n/Ebe ne 2/Rec htlic he Gr undlag en - Über sc hr ift 2 @ 3\mod_1221060626343_21.doc x@ 21 726 @ 2 @ 1
2.1 Legal Bases
Pos: 16.3 / All e Seri en ( A llg e mei ne M o dul e)/R ec htl ich es , Al lg e mei nes /Ä nd er ung s vor beh alt - Üb erschr ift 3 und In halt @ 3\mod_1221060036484_21.docx @ 21720@ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
Pos:16.4/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en ( al te Str u ktur )/ Per s on al qu al if i kati o n/ Per s on alq u ali fi ka tio n 750- xxxx - Ü bersc hrift 3 u nd Inh alt @ 3\mod_1224061208046_21.d ocx @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO I/O SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: nul l /Ser ie 750 (W AGO-I/ O-SYST EM ) / Wic h tig e Erlä uter ung en (al te Str uktur )/Best imm ungsge mäß eV erwen dung/ Besti mmung sge mäße Ver wend ung 750- xxxx - Überschrift3 @ 32\mod_1536041141528_21.docx @ 498494@ 3@ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Pos:16.6/Serie750(WAGO-I/O-SYST EM) / Wic ht ige Erl äuter unge n( alte Str uktur )/Bes timm ungsg emäß e Verwen dung/ Besti mmu ngsge mäße V erwen dung 75 0-xxxx für Ger ät e - ST D - mitEN 61000-6-3 @ 3 \mod_1224064151234_21.docx@ 24070 @ @1
Fieldbus couplers, controllers and I/O modules found in the modular WAGO I/O
SYSTEM 750 receive digital and analog signals from sensors and transmit them
to actuators or higher-level control systems. Using controllers, the signals can
also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO I/O SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information in
the section “Device Description” > “Standards and Guidelines” in the manual for
the used fieldbus coupler or controller.

WAGO I/O SYSTEM 750 XTR Important Notes 9
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Appropriate housing (per 2014/34/EU) is required when operating the WAGO I/O
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F I/O modules within the modular
WAGO I/O SYSTEM 750. Only these safe F I/O modules ensure functional safety
in accordance with the latest international standards. WAGO's interference-free
output modules can be controlled by the safety function.
Pos: 16.7 / All e Seri en ( All g emei ne Mod ule) /R ec htl ic hes , Al lg e mei nes / Te ch nisc her Zus ta nd d er Ger ät e - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1221060446109_21.docx@ 21723@ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
• Repairs,
• Changes to the hardware or software that are not described in the
operating instructions,
• Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
Pos: nul l /Alle S erie n( Allg emeine M odul e)/Ü berschr ifte n/Eb ene 4/En tsorg en - Über sc hr ift 4 @ 30\mod_1510145115652_21.docx @ 469859@ 4 @ 1
2.1.4.1 Disposal
Pos: null /Alle S er ie n ( All gem ei ne M odul e) /Ü bers c hrif te n/E ben e 5/ El ekt ro- un d El e ktr o ni kger ät e - Ü ber sc hr ift 5 @ 32\mod_1537446988068_21.docx@ 501657@ 5@ 1
2.1.4.1.1 Electrical and Electronic Equipment
Pos: null /Alle S er ie n ( All gem ei ne M odul e) /R ech tli ch es, A llg e mein es/ Ele ktr o- und Ele ktr oni kger ät e @ 32\mod_1532425086061_21.docx@ 491989@ @ 1
Electrical and electronic equipment may not be disposed of
with household waste. This also applies to products without
this symbol.
Electrical and electronic equipment contain materials and substances that can be
harmful to the environment and health. Electrical and electronic equipment must
be disposed of properly after use.
WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary
nationally.

10 Important Notes WAGO I/O SYSTEM 750 XTR
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Environmentally friendly disposal benefits health and
protects the environment from harmful substances in
electrical and electronic equipment.
• Observe national and local regulations for the disposal of electrical and
electronic equipment.
• Clear any data stored on the electrical and electronic equipment.
• Remove any added battery or memory card in the electrical and
electronic equipment.
• Have the electrical and electronic equipment sent to your local
collection point.
Improper disposal of electrical and electronic equipment can be harmful to the
environment and human health.
Pos: null /Doku m enta ti on allg e mei n/Gli ed er ung s el em ent e/----Leer z eil e-( 1Z) ---- @ 28\mod_1485262995837_0.docx@ 404006@ @ 1
Pos: null /Alle S er ie n ( All gem ei ne M odul e) /Ü bers c hrif te n/E ben e 5/ Ver pa ckung- Ü bers c hri ft 5 @ 3 2\mod_1537447044202_21.docx @ 501662@ 5@ 1
2.1.4.1.2 Packaging
Pos: null /Alle S er ie n ( All gem ei ne M odul e) /R ech tli ch es, A llg e mein es/ V erp ac kung @ 32 \mod_1537446786416_21.docx @ 501653@ @ 1
Packaging contains materials that can be reused.
PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout
Europe. Directives and laws may vary nationally.
Environmentally friendly disposal of the packaging protects the environment and
allows sustainable and efficient use of resources.
• Observe national and local regulations for the disposal of packaging.
• Dispose of packaging of all types that allows a high level of recovery,
reuse and recycling.
Improper disposal of packaging can be harmful to the environment and wastes
valuable resources.
Pos: 16.1 0 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel eme nt e/---Sei t enw ec hs el--- @ 3 \mod_1221108045078_0.docx @ 21810@ @ 1

WAGO I/O SYSTEM 750 XTR Important Notes 11
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Pos: 16.1 1 / All e S er ie n ( All ge m ein e M o dul e) /Üb er sc hr ift en /E ben e 2/Sich er hei ts hin w eis e - Ü ber s chri ft 2 @ 6\mod_1260180299987_21.docx@ 46724@ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 16.1 2 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- un d sonst ige Hi nweis e/Einl eitu ng Sich erhei tshin weise Har dwar e @ 6\mod_1260180170493_21.docx @ 46720@ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 16.1 3.1 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /G ef a hr /G ef ahr: Nic ht an G erät e n unter Spa nnu ng arbei te n! @ 6\mod_1260180365327_21.docx@ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: null /Alle S er ie n ( All gem ei ne M odul e) / Sich erh eits - und sonst ig e Hi nw eis e/G ef a hr/ G ef ahr : Pr od uk t nur i n eine m g e ei gn et en Geh äus e ei n ba uen! @ 3 3\mod_1543581881435_21.docx@ 511972@ @ 1
Install device in only one suitable enclosure!
The device is an open system. Install the device in a suitable enclosure. This
enclosure must:
• Guarantee that the max. permissible degree of pollution is not exceeded.
• Offer adequate protection against contact.
• Prevent fire from spreading outside of the enclosure.
• Offer adequate protection against UV irradiation.
• Guarantee mechanical stability
• Restrict access to authorized personnel and may only be opened with tools
Pos: null /Alle S er ie n ( All gem ei ne M odul e) / Sich erh eits - und sonst ig e Hi n wei s e/G ef a hr /G ef ahr : T re n n vorr ic ht ung und Ü b ers tr oms c h utz @ 33\mod_1543915978439_21.docx @ 512267@ @ 1
Ensure disconnect and overcurrent protection!
The device is intended for installation in automation technology systems.
Disconnect protection is not integrated. Connected systems must be protected by
a fuse.
Provide suitable disconnect and overcurrent protection on the system side!
os: 1 6. 13. 4 /A ll e Ser i en ( Al lg emei ne Mod ule) /Si ch erh eits - und sons ti ge H i n weis e/ G ef ahr / Gef a hr : U nf al l ver hü tu ng s vor sc hri f te n be ac ht en! @ 6 \mod_1260180657000_21.docx@ 46735 @ @ 1
Pos: 16.1 3.5 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /G ef a hr /G ef ahr: Auf nor mg erec ht e n A nsc hl uss ac ht en! @ 6\mod_1260180753479_21.docx @ 46739@ @ 1
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.
Pos: 16.1 4 / S er ie 750 ( W AG O-I/ O-SYST EM ) / Wic htig e Er l äu ter ung en (alt e Struk t ur) /Si c her hei t s- und sonstigeHinweise/Warnung/Warnung: Speisung ausschließlich aus SELV-/PELV-Versorg ung ( 24 V-XTR -I/O-M odul e) @ 2 9\mod_1493107132163_21.docx @ 41 96 1 8 @ @ 1
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this XTR I/O module
(750-1416/040-000) must be powered from SELV/PELV power supply(s)!
Pos: 16.1 5 / Al le Ser ien ( Allg em ein e M odul e)/Si c herh eits - und sonsti ge Hin wei s e/V orsi c ht/ Vor sic ht : H ei ße Oberfl äc he nicht berü hr en! (all ge m ein) @ 6\mod_1264428115588_21.docx@48610 @ @ 1

12 Important Notes WAGO I/O SYSTEM 750 XTR
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Do not touch hot surfaces!
The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.
Pos: nul l /Ser ie 750 (W AGO-I/ O-SYST EM )/ Wi ch ti g e Er l äut er ung en (alt e St r u ktur ) /Sic her hei ts- u n d s on sti g e H i n w eis e/ Ac ht ung / Ac ht ung : Ein wan dfr ei e Kont a kti eru ng zur T rag s c hie n e g ew ä hrl ei st en! @ 3 4\mod_1550481407638_21.docx@ 530599@ @ 1
Ensure proper contact with the DIN-rail!
Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.
Pos: 16.1 6.2 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /A cht u ng /Ac ht u ng : D ef e kt e od er bes ch ädig t e Gerät e austa usc h en! @ 6\mod_1260180857358_21.docx @ 46743@ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts).
Pos: 16.1 6.3 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /A cht u ng /Ac ht u ng : G er ä te vor kriec hen de n und i soli er end en Sto ff en schüt ze n! @ 6\mod_1260181036216_21.docx@ 46747@ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
Pos: 16.1 6.4 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /A cht u ng /Ac ht u ng : R ei ni gu ng nur mit zul äss ig e n M at er ial ie n! @ 6\mod_1260181203293_21.docx@ 46751@ @ 1
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Pos: 16.1 6.5 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- undsonstigeHinweise/Achtung/Achtung:KeinKontaktsprayverwenden! @ 6\mod_1260181290808_21.docx @ 46755@ @1
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 16.1 6.6 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o nsti g e H i n wei se /A c ht u ng /Ac ht u ng : V er pol ung en der D ate n- un d Vers org u ng s lei t u ng en verm eid e n! @ 6\mod_1260184045744_21.docx@ 46767@ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 16.1 6.7 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- und s o nst ig e Hinw ei se /A cht u ng /Ac ht u ng : El e ktr os t atis c h e E nt la du ng verm ei de n! - DIN EN61340-5-1/-3 @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

WAGO I/O SYSTEM 750 XTR Important Notes 13
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 16.1 7 / S er ie 750 ( W AG O-I/ O-SYST EM ) / Wic htig e Er l äu ter ung en (alt e Struk t ur) /Si c her hei t s- u n d s on sti g e H i n weis e/ Ac ht ung / Ac ht ung : XTR - I s ola ti o nspr üf ung en mit D C durch fü hr e n! @ 1 5\mod_1370843209441_21.docx@ 122210@ @ 1
Use only direct current (DC) for insulation testing!
Both the system voltage and field voltage side are capacitively coupled to the
DIN-rail. If an I/O module is mounted on the DIN-rail, application of an AC voltage
between the DIN-rail and at least one of these two potentials can lead to the
destruction of the module.
Use only direct current (DC) for insulation testing. To avoid destroying the I/O
module, you must discharge it completely before applying the test voltage again.
Pos: 17 /D oku ment ation all g emei n/ Gli e der ung s el e me nte /---Sei t e n wechs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

14 Device Description WAGO I/O SYSTEM 750 XTR
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Pos: 18 /A ll e Seri en (Allg e mei n e M od ul e)/ Ü b ers chr if te n/ Eb e ne 1/G erät e bes c hr ei bung - Üb er schr i f t 1@ 3\mod_1233756084656_21.docx@ 27096 @ 1@ 1
3 Device Description
Pos:19.1/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /Ei nlei t u ng/ A nwe n du ng/ DI /A n we ndu ng 750-x4xx DI @ 3\mod_1233762736718_21.docx@ 27108@ @ 1
The digital input module 750-1416/040-000 (8DI 24 VDC 0.2ms 2-wire XTR)
receives control signals from digital field (e.g. of sensors, transmitters, switches
or proximity switches).
Pos:19.2/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /Ei nlei t ung /I/O-B esc hr ei bu ng /D I/ I/ O-Beschreibung 750-141x8 DI 2-Lei ter (D I und 2 4 V) Pus h-inC AG E C LAM P @ 15\mod_1370934995007_21.docx@ 122344 @ @ 1
The I/O module has 8 input channels, providing a direct connection to 2-wire
sensors.
The sensors are connected to the Push-in CAGE CLAMP®connectors DI 1 and
24 V … DI 8 and 24 V.
Pos:19.3/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /Ei nlei t u ng/ I/ O-B esc hrei bu ng /Al lg e m ein /V er weis auf Kapi tel "An sc hl üs s e" @ 8\mod_1276775378035_21.docx@ 57956@ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos:19.5/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /Ei nlei t u ng/ I/ O-B esc hr ei bu ng /D I/ I/ O-Beschreibung 750-x4xxDI RC-F il t er 0,2 ms @ 3\mod_1233755181796_21.docx@ 27083@ @ 1
Each input channel has a RC noise rejection filter with a time constant of 0.2 ms.
Pos:19.6/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /Ei nlei t u ng/ I/ O-B esc hr ei bu ng /D I/ I/ O-Beschreibung 750-x4xxDI H SS / positivschaltend(24 V) @ 3\mod_1233831724648_21.docx@27231 @ @ 1
The I/O module inputs provide high-side switching. If the 24 V potential for field
power is switched to an input connection, the signal status for the corresponding
input channel is set to “high”.
Pos:19.7/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /Ei nlei t u ng/ LE D-A nz eig e/ LED Zus tan d Signal @ 3\mod_1233755258578_21.docx@ 27087@ @ 1
A green LED indicates the switched status of each channel.
Pos:19.8/Serie750( WAGO-I/ O-SYST EM) / Ger äte b esc hr ei bu ng (alt e S tr u kt ur) /Ei nlei t u ng/ LE D-A nz ei g e/ Ver wei s auf K api tel "A nz ei g eel e me nt e" @ 5\mod_1246010525000_21.docx@ 36194@ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos:19.9/Serie750(WAGO-I/ O-SYST E M) / Ger ät eb es c hrei bu ng ( al t e St r u ktur ) /Ei nl eit u ng /V er sor g ung / Ver s or g ung 24 V , 0 V üb er Leis tu ng s ko nt ak te Stand ar d @ 3\mod_1226498974531_21.docx @ 25020@ @ 1
The I/O module 750-1416/040-000 (8DI 24 VDC 0.2ms 2-wire XTR) receives the
24 V voltage supply for the field level from an upstream I/O module or from the
fieldbus coupler/controller via blade-formed power jumper contacts. It then
provides these potentials to subsequent I/O modules via spring-formed power
jumper contacts.
Pos: 19.1 0 / S er ie 750 ( W AG O-I/ O-SYST EM ) / Wic htig e Er l äu ter ung en (alt e Struk t ur) /Si c her hei t s- und sonstigeHinweise/Warnung/Warnung: Speisung ausschließlich aus SELV-/PELV-Versorg ung ( 24 V-XTR -I/O-M odul e) @ 29\mod_1493107132163_21.docx @ 419618@ @ 1
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this XTR I/O module
(750-1416/040-000) must be powered from SELV/PELV power supply(s)!
Pos: 19.1 1 / S er ie 750 ( W AG O-I/ O-SYST EM ) / Wic htig e Er l äu ter ung en (alt e Struk t ur) /Si c her hei t s- u n d s on sti g e H i n weis e/ Ac ht ung / Ac ht ung : Maxi m aler Str o m L ei st u ng s kont a kt e 1 0 A @ 3\mod_1226499143500_21.docx@ 25029@ @ 1
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.
Pos: 19.1 2 / S er ie 750 ( W AG O-I/ O-SYST EM ) / Wic htig e Er l äu ter ung en (alt e Struk t ur) /Si c her hei t s- und s onst ig e Hi n weis e/Hi n wei s/H in weis : P ot enti al eins p eise mo dul für Er de eins etz en! (kei ne LK f ür Erde) @ 3\mod_1226499037468_21.docx @ 25023@ @ 1

WAGO I/O SYSTEM 750 XTR Device Description 15
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Pos: 19.1 3 / S er ie 750 ( W AG O-I/ O-SYST EM ) /G er ät ebe s chr ei b u ng ( alt e Stru ktur )/ E inl ei t ung / Ver s org u ng /G al va nis c he Tren nu ng Feld/ S ys te m @ 3\mod_1233756478750_21.docx @ 27102@ @ 1
The field voltage and the system voltage are electrically isolated from each other.
Pos: 19.1 4 / S er ie 750 ( W AG O-I/ O-SYST EM ) /G er ät ebe s chr ei b u ng ( alt e Stru ktur )/ E inl ei t ung / Ver s org u ng /A nor dn u ng unter Ber üc ksi c hti g ung derLeistungskontaktebeliebig@ 3\mod_1233756233468_21.docx@ 27099@ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node.
An arrangement in groups within the group of potentials is not necessary.
Pos: 19.1 5 / S er ie 750 ( W AG O-I/ O-SYST EM ) / Wic htig e Er l äu ter ung en (alt e Struk t ur) /Si c her hei t s- u nd sonstige Hi nweise/Hinweis/Hinweis:XTR - M isc hb etri e b X TR / St and ar d @ 1 5\mod_1367496420828_21.docx@118326@ @1
Mixed operation
Mixed operation (standard/XTR modules) within a node is possible when groups
of modules are electrically isolated on the field side (i.e., electrically isolated
power supply).
Pos: 19.1 6 / S er ie 750 ( W AG O-I/ O-SYST EM) /Wi chtig e Er l äuter ung en (alt e St ru k t ur) /Si c her hei t s- un d sonstige Hi nweise/Hinweis/Hinweis:XTR - E r hö ht e S t örf es tig keit @ 1 5\mod_1367496424993_21.docx@ 118330 @ @ 1
Increased interference!
For standard-compliant application in substation instrumentation and control,
telecontrol systems, railway technology or shipbuilding certified operation,
field-side power supply filter 750-624/040-001 or power supply filter
750-626/040-000 are generally to be used for XTR module groups.
Pos: 19.1 7 / S er ie 750 ( W AG O-I/ O-SYST EM )/G er ät e be schr eib u ng (alt e S tru k tur) / Ei nl ei t ung/ Ei ns at z ber ei c h/ Eins at zb er eic h 750- xxxx/040-0 00 all e XTR-Kop pler / Co ntr ol ler ohne Eins c hrä nk ung+ M isc hb etr ie b hin wei se @ 15\mod_1368425919479_21.docx@ 119444@ @ 1
The I/O module can be operated with all fieldbus couplers/controllers of the
WAGO I/O SYSTEM 750 XTR.
Observe the instructions for mixed operation when used in mixed operation
behind standard fieldbus couplers/controllers.
Pos: 20 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

16 Device Description WAGO I/O SYSTEM 750 XTR
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Pos: 21 /Al l e S eri en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 2/ A nsic ht - Ü b ers chr if t 2 @ 4 \mod_1240984217343_21.docx@ 31958@ 2 @ 1
3.1 View
Pos: 22 / S eri e 750 ( WA G O-I/ O-SYST EM ) / Ger ät eb esc hrei bu ng ( al t e Str u ktur ) /A nsi c ht/D I/ Ans ic ht 75 0-141x_0040-xxxx 8 D I 2-L ei ter HSS @ 15\mod_1369736961941_21.docx@ 120682@ @ 1
Figure 1: View
Pos: 23 / S eri e 750 ( WA G O-I/ O-SYST EM ) / Ger ät eb esc hrei bu ng ( al t e Str u ktur ) /A nsi c ht/ A nsi ch t Push-in CageClamp®_Legendemit LEDs@ 15\mod_1370852562803_21.docx@ 122213@ @ 1
Table 3: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > “Connectors”
4
Push-in CAGE CLAMP®
connectors
“Device Description” > “Connectors”
5
Power jumper contacts
“Device Description” > “Connectors”
6
Release tab
“Mounting” > “Inserting and Removing
Devices”
Pos: 24 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

WAGO I/O SYSTEM 750 XTR Device Description 17
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Pos: 25 /Al l e S eri en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 2/ A nsc hlüs se - Ü ber sc hr ift 2 @ 4\mod_1240984262656_21.docx @31961 @ 2@ 1
3.2 Connectors
Pos: 26 / S eri e 750 ( WA G O-I/ O-SYST EM ) / Ger ät eb esc hrei bu ng ( al t e Str u ktur ) /A nsc hl ü ss e/ Da te n kon ta kte /L o kal b us - Ü b er sc hri f t 3@ 6\mod_1256294684083_21.docx@43660 @ 3@ 1
3.2.1 Data Contacts/Local Bus
Pos:27.1/Serie750(WAGO-I/O-S YST EM ) / Ger äte b esc hr ei bu ng (alteStruktur)/Anschlüsse/Datenkontakte - Fel dbus ko ppl er /-c ontroll er und M odule – Ab bi ld u ng und B es c hr ei b ung @ 3\mod_1231771259187_21.docx@26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the local bus. The
contacting for the local bus consists of 6 data contacts, which are available as
self-cleaning gold spring contacts.
Figure 2: Data Contacts
Pos:27.2/Serie750(WAGO-I/O-SYST EM ) / Wic ht ig e Erlä ut eru ng e n ( al te Str u ktur )/ Sic h er h eits - undsonstigeHinweise/Achtung/Achtung:I/O-Module nic ht auf Gol dfeder kont akte leg en! @ 7\mod_1266318463636_21.docx@ 50695@ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: nul l /Ser ie 750 (W AGO-I/ O-SYST EM )/ Wi ch ti g e Er l äut er ung en (alt e St r u ktur ) /Sic her hei ts- u n d s on sti g e H i n w eis e/ Ac ht ung / Ac ht ung : ESD - Au f Po te nti al aus gl eic h der U mg eb ung ac hten! @ 3 2\mod_1539077262331_21.docx@ 504433@ @ 1
Pay attention to potential equalization from the environment!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, please ensure that
environmental factors (personnel, work space and packaging) are properly
equalized. Do not touch any conducting parts, e.g., data contacts.
Pos: 28 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\ mod_1221108045078_0.docx@ 21810 @ @ 1

18 Device Description WAGO I/O SYSTEM 750 XTR
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Pos: 29 / S eri e 750 ( WA G O-I/ O-SYST EM ) / Ger ät eb esc hrei bu ng ( al t e Str u ktur ) /A nsc hl ü ss e/ Lei st u ng sk ont a kt e/F el d ver s org ung - Üb er schr i f t 3 @ 6\mod_1256294692864_21.docx@ 43664 @ 3@ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 30 / S eri e 750 ( WA G O-I/ O-SYST EM ) / Wic hti g e Er l äut er u ng e n ( al te Str ukt ur )/S ic h er h eits - un d so nst ig e H in wei s e/ War nung / War n ung : S peis u ng aussc hl ieß lic h aus S E LV-/PE L V-V er sor g u ng ( 2 4V-XT R-I/O-M odul e) @ 2 9\mod_1493107132163_21.docx @ 419618@ @ 1
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this XTR I/O module
(750-1416/040-000) must be powered from SELV/PELV power supply(s)!
Pos:31.1/Serie750( WAGO-I/ O-SYST EM) / Wi c htig e Erlä ut er ung e n (al te Stru kt ur )/Si c h er hei ts - und s o nsti g e H in wei se /V orsi c ht/ Vors ic ht : V erl e tz ungs ge fa hr durc h sc h ar f kan tig e M es ser k ont a kte! @ 6\mod_1256193279401_21.docx@ 43414@ @1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury. Do not touch the blade contacts.
Pos:31.2/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /A nsc hlüs s e /L eis t ungs ko nt a kte 2 LK (Mes s er/ F ed er) - Einl ei tung @ 1 5\mod_1371721641099_21.docx@ 123714 @ @ 1
The I/O module 750-1416/040-000 has 2 self-cleaning power jumper contacts
that supply and transmit power for the field side. The contacts on the left side of
the I/O module are designed as blade contacts and those on the right side as
spring contacts.
Pos:31.3/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /A nsc hlüs s e /L eis t ungs ko nt a kte 2 LK (Mes s er/ F ed er) - Abbi l dung (16-Kanal)@ 15\mod_1370866610582_21.docx @ 122222@ @1
Figure 3: Power Jumper Contacts
Pos:31.4/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /A nsc hlüs s e /L eis t ungs ko nt a kte 2 LK (Mes s er/ F ed er) - Legende@ 15\mod_1371721352500_21.docx@ 123710 @ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (U
v
) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (Uv) for field supply
Pos:31.5/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en ( al te Str u ktur )/ Sic h er h eits - undsonstigeHinweise/Achtung/Achtung:MaximalerStrom Leistungskontakte10 A @ 3\mod_1226499143500_21.docx@ 25029@ @ 1

WAGO I/O SYSTEM 750 XTR Device Description 19
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.
Pos: 32 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1
Pos: 33 / S eri e 750 ( WA G O-I/ O-SYST EM ) / Ger ät eb esc hrei bu ng ( al t e Str u kt ur) /A ns c hl üs se /P us h-in C AG E C LAM P®- Anschlüsse - Ü ber sc hr ift 3 @ 15\mod_1370519905692_21.docx@ 122018@ 3 @ 1
3.2.3 Push-in CAGE CLAMP®Connectors
Pos: 34 / S eri e 750 ( WA G O-I/ O-SYST EM ) / Wic hti g e Er l äut er u ng e n ( al te Str ukt ur )/S ic h er h eits - und sonstigeHinweise/ War nung / War n ung : S peis u ng aussc hl ieß lic h aus S E LV-/PE L V-V er sor g u ng ( 2 4V-XT R-I/O-M odul e) @ 2 9\mod_1493107132163_21.docx @ 419618@ @ 1
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this XTR I/O module
(750-1416/040-000) must be powered from SELV/PELV power supply(s)!
Pos: 35 / S eri e 750 ( WA G O-I/ O-SYST EM ) / Ger ät eb esc hrei bu ng ( al t e Str u ktur ) /A nsc hl ü ss e/ DI/ An s chl üs s e 75 0-14 1 x 8 D I 2-Leiter HS S P us h-i n C A GE C LAM P @ 7\mod_1274262794032_21.docx@ 56626@ @ 1
Figure 4: Push-in CAGE CLAMP® Connectors
Table 5: Legend for Figure “Push-in CAGE CLAMP® Connectors”
Channel
Designation
Connector
Function
1
DI 1
1
Input DI 1: Signal voltage
24 V
9
Input DI 1: Sensor supply +24 V
2
DI 2
2
Input DI 2: Signal voltage
24 V
10
Input DI 2: Sensor supply +24 V
.
.
.
7
DI 7
7
Input DI 7: Signal voltage
24 V
15
Input DI 7: Sensor supply +24 V
8
DI 8
8
Input DI 8: Signal voltage
24 V
16
Input DI 8: Sensor supply +24 V

20 Device Description WAGO I/O SYSTEM 750 XTR
750-1416/040-000 8DI 24 VDC 0.2ms 2-wire XTR
Manual
Version 1.1.0
Pos: 36 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1
Pos: 37 /Al l e S eri en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 2/ A nzeig eel e ment e - Ü b ers chr if t 2 @ 4 \mod_1240984390875_21.docx@ 31964 @ 2@ 1
3.3 Display Elements
Pos: 38 / S eri e 750 ( WA G O-I/ O-SYST EM ) / Ger ät eb esc hrei bu ng ( al t e Str u ktur ) /A nz ei geel e ment e/ D I/ Anz ei g e ele m ent e 7 5 0-141x8 DI @ 7\mod_1274352179347_21.docx@ 56795@ @ 1
Figure 5: Display Elements
Table 6: Legend for Figure “Display Elements”
Channel
Designation
LED
State
Function
1 State DI 1 1
Off
Input DI 1: Signal voltage (0)
Green
Input DI 1: Signal voltage (1)
.
.
.
8 State DI 8 8
Off
Input DI 8: Signal voltage (0)
Green
Input DI 8: Signal voltage (1)
Pos: 39 /Al l e S eri en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 2/ B edi enel e ment e - Ü ber s chri ft 2 @ 4\mod_1239191655456_21.docx@ 30439@ 2 @ 1
3.4 Operating Elements
Pos: 40 /S erie 7 50 (WA GO -I/O-S YST EM )/ Ger ät eb esc hr ei bu ng (alt e Stru kt ur) /B e die nel e ment e/ Be di en el e me nte I/O-Modul 75x-xxxxnich t vorhanden @ 4\mod_1236322031125_21.docx @ 28063@ @ 1
The I/O module 750-1416/040-000 has no operating elements.
Pos: 41 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1