WAGO 753-646 User manual

Manual
WAGO-I/O-SYSTEM 750
753-646
KNX/EIB/TP1 Module
Device Mode
Version 1.2.0

2
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
© 2018 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

Table of Contents 3
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
Table of Contents
1Notes about this Documentation.............................................................5
1.1 Validity of this Documentation.................................................................5
1.2 Copyright................................................................................................5
1.3 Symbols .................................................................................................6
1.4 Number Notation ....................................................................................8
1.5 Font Conventions ...................................................................................8
2Important Notes ........................................................................................9
2.1 Legal Bases............................................................................................9
2.1.1 Subject to Changes............................................................................9
2.1.2 Personnel Qualifications ....................................................................9
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying
Provisions ..........................................................................................9
2.1.4 Technical Condition of Specified Devices.........................................10
2.1.4.1 Disposal ......................................................................................10
2.2 Safety Advice (Precautions) .................................................................11
3Device Description..................................................................................13
3.1 View .....................................................................................................15
3.2 Connectors...........................................................................................16
3.2.1 Data Contacts/Local Bus..................................................................16
3.2.2 CAGE CLAMP®Connectors.............................................................17
3.3 Display Elements..................................................................................18
3.4 Operating Elements..............................................................................19
3.5 Schematic Diagram..............................................................................20
3.6 Technical Data .....................................................................................21
3.6.1 Device Data .....................................................................................21
3.6.2 Supply..............................................................................................21
3.6.3 KNX Communication........................................................................21
3.6.4 Connection.......................................................................................21
3.6.5 Climatic Environmental Conditions...................................................22
3.7 Approvals .............................................................................................23
3.8 Standards and Guidelines ....................................................................24
4Function Description ..............................................................................25
4.1 Application of Module 753-646 with Programmable Fieldbus Controllers26
4.1.1 Interworking Datapoint Types...........................................................26
4.2 Data Exchange between KNX/EIB/TP1 Module and IEC Application....27
4.3 Startup Behavior of the KNX/EIB/TP1 Module in Device Mode.............27
4.4 Installation Notes..................................................................................29
5Process Image.........................................................................................31
6Mounting..................................................................................................32
6.1 Mounting Sequence..............................................................................32
6.2 Inserting and Removing Devices..........................................................33
6.2.1 Inserting the I/O Module...................................................................33
6.2.2 Removing the I/O Module ................................................................34
6.3 I/O Modules with Pluggable Wiring Level (Series 753) .........................35

4 Table of Contents
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
6.3.1 Coding .............................................................................................36
6.3.2 Plug Removal ..................................................................................38
List of Figures ..................................................................................................39
List of Tables....................................................................................................40

Notes about this Documentation 5
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
1 Notes about this Documentation
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
1.1 Validity of this Documentation
This documentation is only applicable to the I/O module 753-646
(KNX/EIB/TP1 Module).
The I/O module 753-646 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.

6 Notes about this Documentation
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
1.3 Symbols
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.

Notes about this Documentation 7
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).

8 Notes about this Documentation
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
1.4 Number Notation
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
1.5 Font Conventions
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.:
Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under
Start of measurement range
.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]

Important Notes 9
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
2 Important Notes
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
2.1 Legal Bases
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information in
the section “Device Description” > “Standards and Guidelines” in the manual for
the used fieldbus coupler/controller.
Appropriate housing (per 2014/34/EU) is required when operating the
WAGO-I/O-SYSTEM 750 in hazardous environments. Please note that a

10 Important Notes
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
prototype test certificate must be obtained that confirms the correct installation of
the system in a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F-I/O modules within the modular
WAGO-I/O-SYSTEM 750. Only these safe F-I/O modules ensure functional
safety in accordance with the latest international standards. WAGO's
interference-free output modules can be controlled by the safety function.
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
• Repairs,
• Changes to the hardware or software that are not described in the
operating instructions,
• Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
2.1.4.1 Disposal
Recycle metals, plastics and packaging materials.
Automation components used in the professional sector (B2B) must be properly
disposed of once no longer in use in accordance with the respective national
guidelines (e.g., European Community Directive WEEE 2012/19/EU).
Packaging of all types must be disposed of in such a way that a high level of
recovery, reuse and recycling is possible. PPWD 94/62/EU and 2004/12/EU
packaging guidelines apply throughout Europe.

Important Notes 11
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
2.2 Safety Advice (Precautions)
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Do not use in telecommunication circuits!
Only use devices equipped with ETHERNET or RJ-45 connectors in LANs.
Never connect these devices with telecommunication networks.
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.

12 Important Notes
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.

Device Description 13
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
3 Device Description
The KNX/EIB/TP1 module 753-646, a.k.a. KNX module, provides the integration
of two-wire TP1 networks or individual KNX devices into all relevant WAGO
building automation controllers.
The KNX module can be operated in the operating modes Device mode or
Router mode. In a KNX IP controller, the module can assume either the device or
router mode. When using a different WAGO controller, the module will operate in
device mode only.
If one or more KNX modules are operated in a KNX IP controller, it behaves as a
normal KNX device (device mode) within the TP1 network. This is also the case
when used with a different WAGO controller. The position, upstream or
downstream, of the KNX module is irrelevant.
The controller and the module are coupled via the local bus. The module also
features four termination points for the connection of the KNX bus line (two KNX
+in red and two KNX –in dark gray). As per EIBA/KNX Association, a standard
MSR conductor (e.g., PYCYM 2×2×0.8) or a telecommunications cable (e.g., J-
Y(St)Y 2×2×0.8) is recommended for the KNX bus line (red and black wires). The
bus line is installed in free topology (ring topologies may not be created). In
addition, the conductor length of the bus line is limited, and maximum conductor
lengths between bus devices may not be exceeded, therefore, general KNX
directives must be adhered to.
The I/O module has two programming buttons for parameterization in device
mode.
The engineering tool software (ETS) requests the actuation during activation of
the KNX module. And, together with the WAGO-specific ETS Plug-in, this
software is used for the activation and configuration of KNX devices.
Eight colored LED's on the modules’ enclosure signal active and inactive
operating modes, the data transfer via KNX and the local bus, the presence of a
KNX bus voltage, and internal states or fault conditions of the module (see
chapter “Display Elements“).

14 Device Description
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
Note the compatibility with couplers/controllers!
Not all controllers are supported by the KNX/EIB/TP1 module 753-646 at the
moment (update 03/2014).
The KNX module does not work with the following controllers:
• INTERBUS controller (750-804)
• DeviceNet controller (750-806)
• MODBUS controller (750-812, -814, -815, -816)
The utilization of the module on couplers is excluded.
Additional Information
Detailed notes to the WAGO ETS Plug-in and the Plug-in itself can be found on
the website http://www.wago.com.

Device Description 15
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
3.1 View
d
Figure 1: View
Table 3: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
-
2
Status-LEDs
“Device Description” > “Display
Elements”
3
Data contacts
“Device Description” > “Connectors”
4
Release tab
“Mounting” > “Inserting and Removing
Devices” and “I/O Modules with
Pluggable Wiring Level (Series 753)”
5
Programming button
“Device Description” > “Operating
Elements”
6
Coding possibility with plastic
pins
“Mounting” > “Coding”
7
Test port
-
8
+ KNX bus
“Device Description” > “Connectors“
9
Attention: Plug internally bridged
-
10
- KNX bus
“Device Description” > “Connectors”
11
Fixing lug for cable ties
“Mounting” > “I/O Modules with
Pluggable Wiring Level (Series 753)”

16 Device Description
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
3.2 Connectors
3.2.1 Data Contacts/Local Bus
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the local bus. It is
comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.

Device Description 17
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
3.2.2 CAGE CLAMP®Connectors
Figure 3: CAGE CLAMP®Connectors
Table 4: Legend for Figure “CAGE CLAMP®Connectors”
Channel
Connector
Function
-
1
Not connected
-
2
Programming button
*)
3
+ KNX bus
*)
4
- KNX bus
-
5
Not connected
-
6
Programming button
*)
7
+ KNX bus
*)
8
- KNX bus
*)
The KNX module has an internal bridge between the KNX+ and KNX- connections.

18 Device Description
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
3.3 Display Elements
Figure 4: Display Elements
Table 5: Legend for Figure “Display Elements”
LED
Designation
State
Function
A Router mode
Off
Operating mode Router not active
On
Operating mode Router active
Flashing
Synchronization
B KNX programming mode
Off
KNX programming mode not active
On
KNX programming mode active
Flashing
Checksum error
C Data transfer local bus
Off
Local bus data transfer not active
Flashing
Local bus data transfer active
D Data transfer KNX
Off
KNX data transfer not active
Flashing
KNX data transfer active
E Device mode
Off
Device mode not active
On
Device mode active
Flashing
Synchronization
F Buffer overflow
Off
No buffer overflow
On
Overflow
G Internal fault
Off
No fault
On
Checksum error / device not
configured
H KNX bus voltage
Off
KNX bus voltage not available
On
KNX bus voltage available

Device Description 19
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
3.4 Operating Elements
The I/O module has two programming button connections (see figure below) for
parameterization of the KNX module in the device mode.
Figure 5: Programming Button
Actuation of the buttons is requested by the engineering tool software (ETS)
during startup of the module.
A temporary electrical connection is established between these two
programming button connectors (2 and 6), via a wire jumper for example,
which activates the programming mode.

20 Device Description
753-646 KNX/EIB/TP1 Module
Manual
Version 1.2.0
3.5 Schematic Diagram
Figure 6: Schematic Diagram