WaterLogic WL200 Manual

Waterlogic Commercial Products, LLC
11710 Stonegate Circle
Omaha, NE 68164
[phone] www.waterlogic.us
Tech Portal Website: http://techportal.waterlogic.com
WL200
OPERATING, INSTALLATION, AND SERVICE MANUAL


WL200Operating,Installation,andServiceManual Page2‐Revision:4‐13‐2016

WL200OPERATING,INSTALLATION,ANDSERVICEMANUAL

CongratulationsonyourchoiceoftheWaterlogicWL200watertreatmentsystem.TheWL200
modeldispensescoldwater.EveryWL200includes:


Bio‐CoteAnti‐MicrobialProtection


Filterconfigurationcanbeoptimizedforallwaterconditions


TheWaterlogicWL200providesexceptionalqualityandgreattastingwaterwitheveryuse.


TABLEOFCONTENTS

FeaturesandBenefits.................................................................3
Certifications...............................................................................4
IntroductionandSafetyAlertSymbols.......................................5
SafetyPrecautions......................................................................6
ModelandPartDesignations......................................................7
Specifications..............................................................................7
OperatingInstructions................................................................8
FlowDiagrams.............................................................................9
AdjustingColdSetPoint............................................................11
Pre‐InstallationProcedures......................................................12
DrainingProcedures..................................................................15
InstallationProcedures.............................................................18
ServiceRequirements...............................................................20
CounterTopDrawingsandPartsList……………………..................21
TowerDrawingsandPartsLists................................................26
ElectricalDiagrams....................................................................31
Troubleshooting........................................................................34
Warranty..................................................................................41

WL200Operating,Installation,andServiceManual Page3‐Revision:4‐13‐2016
WL200FEATURESANDBENEFITS



ColdWater
WaterlogicWL200comesstandardwithColdWaterSelection.

HighVolumeStorageandWaterCapacity
TowerModelhas4litersofColdWaterCapacity.CounterTophas2litersofColdWaterCapacity.

BioCote®Anti‐MicrobialProtection
Plasticsurfacessurroundingdispensingareasanddriptrayareinfusedwithan
exclusivesilveradditivecalledBioCote®.Silverisanaturalanti‐microbialthat
inhibitsthegrowthofmicroorganismsprovidingadditionalsurfaceprotection.

LargeDispenseAreawithRecessedFaucet
8.5inchdispenseheightwithBioCote®recessedfaucettoprotectfromcross‐contamination.




WL200Operating,Installation,andServiceManual Page4‐Revision:4‐13‐2016
WL200CERTIFICATIONS 

Waterlogicwatertreatmentsystemshavebeentested,andcertifiedtorigorousNSFandUL
Standards.WebelievethatperformancetestingandcertificationsvalidateWaterlogicasaworld‐
leaderinwatertreatmentsystems.
WL200CertificationsInclude
UL399–CertifiedDrinkingWaterCooler
IntertekLabs(ETL)CertifiedtheWL200toANSI/UL399StandardforDrinkingWater
Coolers.




BPAFree‐WaterlogictestsforBPAanddeclaresthatallofitsproductsareBisphenol‐A
FREEandcontainnoharmfulBPAplastics.




WaterlogicmanufacturingiscertifiedtoISO9001–QualityManagement
Systems(certifiedbyMoodyInternational).ISO9001isthe
internationallyacceptedstandardforwellmanagedorganizationsthat
haveadoptedthekeyqualitymanagementprinciplestoitsoperationsto
bringconsistentqualityproductsandacultureofcontinuous
improvement.
SafeDrinkingWaterAct
WaterlogicwatertreatmentsystemsconformtotheSafeDrinkingWaterAct(SWDA)“lead‐free”
amendmenteffectiveJanuary4,2014.



WL200Operating,Installation,andServiceManual Page5‐Revision:4‐13‐2016
INTRODUCTION

CarefullyreadandfollowallinstructionstoensureproperandefficientoperationofyourWL200.
ContactWaterlogicoranAuthorizedWaterlogicDealerifyouhaveanyquestions.

WaterlogicandAuthorizedWaterlogicDealersemploytrainedservicepersonnelwhoare
experiencedintheinstallation,functionandrepairofWaterlogicequipment.Thispublicationis
writtenforusebythesequalifiedindividuals.Waterlogicencouragesuserstolearnaboutproducts,
however,webelievethatproductknowledgeandserviceisbestobtainedbyconsultingWaterlogic
oranAuthorizedWaterlogicDealer.

Waterlogicwatertreatmentsystemsshouldbecombinedwithselectedwatertreatment
componentstocreateasystemspecificallytailoredforeachapplicationbytrainedandqualified
personnel.

ProductsmanufacturedandmarketedbyWaterlogicanditsaffiliatesareprotectedbypatents
issuedorpendingintheUnitedStatesandothercountries.

Waterlogicreservestherighttochangethespecificationsreferredtointhisliteratureatanytime,
withoutpriornotice.ChangesormodificationsnotexpresslyapprovedbyWaterlogiccouldvoidthe
warrantyanduser’sauthoritytooperatetheequipment.


SAFETYALERTSYMBOLS

Readandfollowallsafetyinformationcarefully.Thesignalwordsusedinthismanualareselectedas
shownbelowandbasedonanassessmentofthedegreeofpotentialinjuryordamage(severeor
minor)andtheoccurrenceofinjury(definitelyoccursorhasthepotentialtooccur)whenthe
warningisignored:

DANGER!
Indicatesasituationwhich,whennotavoided,resultsindeathorsevereinjury.

WARNING!
Indicatesasituationwhich,whennotavoided,hasthepotentialtoresultindeathorsevere
injury;and/orseverepropertydamage.
 
CAUTION!
Indicatesasituationwhich,whennotavoided,resultsorhasthepotentialtoresultinminor
injury;and/orminorpropertydamage.


WL200Operating,Installation,andServiceManual Page6‐Revision:4‐13‐2016
SAFETYPRECAUTIONS

Basicsafetyprecautionsshouldbefollowed,includingthefollowing:

DANGER!Ifincorrectlyinstalled,operatedormaintained,thisproductcancausedeathor
severeinjury.Thosewhoinstall,operate,ormaintainthisproductshouldbetrainedinitsproperuse,
warnedofitsdangers,andshouldreadtheentiremanualbeforeattemptingtoinstall,operate,or
maintainthisproduct.

WARNING!Unitistobeusedforitsintendedpurposeasdescribedinthismanual,and
untrainedindividualswhousethismanualassumetheriskofanyresultingpropertydamageor
personalinjury.

DANGER!ELECTRICALSHOCKHAZARD.Alwaysunplugfrompowersupplypriortoservicing
equipmenttopreventelectricalshock.

WARNING!Thissystemtobeusedforwateronlyandisnotintendedforusewherewateris
microbiologicallyunsafeorwithwaterofunknownqualitywithoutadequatedisinfectionbeforeor
afterthesystem.Thesystemisdesignedforthesupplementalbactericidaltreatmentofeither
treatedanddisinfectedpublicdrinkingwater,orotherdrinkingwater,whichhasbeentestedand
deemedacceptableforhumanconsumptionbythestateorlocalhealthagencyhavingjurisdiction.
Thesystemisdesignedtoreducenormallyoccurringnon‐pathogenicornuisancemicroorganisms
only.Systemisnotintendedfortreatmentofcontaminatedwater.

WARNING!DispenserCouldTiporFallcausingseriousinjury.Alwaysinstallunitonafirm,flat,
andlevelsurfaceandsecuretheWL200tothebasecabinetwiththescrewprovidedtolockthe
componentstogether.Neverplaceheavyitemsontopofunitandneverclimb,stand,orhangonunit
orstoragecabinettopreventinjuryanddamage.
 

CAUTION!INDOORUSEONLY.Donotinstalloutdoorsorwhereunitisindirectsunlight.Donot
installwhereambienttemperaturegoesbelow50Forabove97F.Avoidhighhumidityandmoisture.
Productlifeandperformancewillbeimpactedandwarrantycouldbevoided.


WL200Operating,Installation,andServiceManual Page7‐Revision:4‐13‐2016
MODEL/PARTDESIGNATIONS
BRANDNAMEDESCRIPTIONMODEL‐
PARTNUMBER
WL200CounterTopWaterlogicWL200CounterTop‐ColdWater
F‐6002‐M‐C‐TT‐CS‐WLU12‐WL200CT
WL200TowerWaterlogicWL200Tower‐ColdWater
F‐6002‐FS‐C‐TT‐CS‐WLU12‐WL200FS


SPECIFICATIONS
ITEMWL200CounterTopWL200Tower
WaterConnection¼”QuickConnect
ColdWaterTemperatureColdWaterTemperature
–
FactorySetPoint41°‐ 5°C
(Adjustable)34° - 54° F.(1.1°‐12.2°C)
RecommendedService
Pressure40‐60psi(275‐414kPa)–UsePressureRegulator
MaximumServicePressure100psi(689kPa)–UsePressureRegulator
RatedServiceFlow0.5gallonsperminute(1.89Lpm)
EnvironmentalTemperature35°‐100°F(2°‐37°C)
RefrigerantGasR134a,40g,1.41ouncesR134a,65g,2.29ounces
R134aPressuresHigh(230psi),Low(90psi)



SHIPPINGSPECIFICATIONS
ITEMWL200CounterTopWL200Tower
Width/Depth/Height13.5”x14.5”x17.75”#(34cmx37cmx
45cm)
13.5”x14.5 x40.5”(34cmx41cmx
103cm)
Weight(dry)42pounds(19.5kg)58pounds(26.5kg)



ELECTRICALSPECIFICATIONS
ELECTRICALSUPPLY120V/60Hz,1PH15AmpService
COMPONENTPOWER(approximate)AMPDRAW(approximate)
Compressor2161.8Amps
WL200TOTAL2161.8Amps


#WL200CounterTopis17.75in.tallandmaynotfitbetweenCounterTopsandcabinets‐Checkinstallationtoensureadequateclearance.

WL200Operating,Installation,andServiceManual Page8‐Revision:4‐13‐2016
OPERATINGINSTRUCTIONS
























TheabovepictureshowsfrontLCDdisplayandcontrolpanelfortheWaterlogicWL200.


ForColdWater:PresstheDispensingButton.


DispensingButton

WL200Operating,Installation,andServiceManual Page9‐Revision:4‐13‐2016
WL200COUNTERTOPWATERFLOWDIAGRAM







WL200Operating,Installation,andServiceManual Page10‐Revision:4‐13‐2016

WaterIn
FilterDryer

SolenoidValve
Compressor
Condenser

WaterOut

Faucet

WL200TOWERWATERFLOWDIAGRAM



WL200Operating,Installation,andServiceManual Page11‐Revision:4‐13‐2016
ADJUSTINGCOLDSETPOINT

Thecoldsetpointcanbeadjustedbyaccessingthecoldthermostat
adjustmentscrewUndertheDecalattherearoftheunit.
ThiswillNOTVoidtheWarrantyasthecurrentDecalstatesonthebackof
theunit.Thefactorysetpointis~41°Fandisindicatedbythedotonsheet
metalaroundtheadjustmentscrewandbehindthedecal.
Turningtheadjustmentscrewclockwiselowersthesetpointtemperature
andtherangeisapproximately20°Fthruthefullrangeofadjustment
(~7:00tothe~5:00positions).

Youshouldbeabletoturnthescrewfromthefactorysetpointof41°F
(~12:00position)about45degreesclockwise(2:30onaclock)toreduce
thesetpointtemperatureby6°Fandachievethe35‐36°Fsettingyouare
lookingfor.

Trialthisbyadjustingandthenmeasurethewatertemperature10‐15
minutesafterthecompressorshutsoff(coldestpoint)toverifytheset
pointtemperature.

Eachunitwillvaryslightly.Trynottogomuchpastthe“3:00position”to
avoidfreezingthecoldtankasshownabove.




FutureProductionchangesColdThermostatCoverLabeltoLP‐0326‐L00‐
00/WLUSAPNLP‐0326.






WL200Operating,Installation,andServiceManual Page12‐Revision:4‐13‐2016
PRE‐INSTALLATIONPROCEDURES

DANGER!ELECTRICALSHOCKHAZARD.
Onlyqualifiedpersonnelwhohavereadandunderstandthisentiremanualshouldattemptto
install,orservicethisunit,failuretodosocouldresultindeathorseriousinjury.DONOTplug
intoanelectricalsupplyuntilspecificallyinstructed.
 
WARNING!ALWAYSSANITIZEBEFOREUSE.
Sanitizebeforeusetoeliminateanypotentialmicrobiologicalcontaminates.

MaterialsNeeded:
PersonalProtectiveEquipment.RubberorNitrileSafetyGlovesandProtectiveEyewear
PhillipsScrewdriver
TemperatureGage
WaterPitcherorContainertocollectwaterfromthefaucet
5galloncontainerordrainbasin
Sanitizer‐HouseholdBleach(5.25%SodiumHypochlorite)orCitricAcidBasedCleaner
¼”PlasticTubing,atleast4feetinlength,andassorted¼”quickconnectfittings
TDSMeterandTestStripsformeasuringchlorine‐Optional

1. UnpacktheWaterlogicWL200andcheckexteriorfordamage.
 
Sanitizing

SanitizeusingaHouseholdBleach(5.25%SodiumHypochloritesolution)orotherapproved
cleanerthroughoutthecoldandsparklingwatercircuits.Followallinstructionsonthesanitizer
andflushwithfreshwaterthroughthefaucetuntilodorandtasteisacceptable.

WARNING!USEPROPERPERSONALPROTECTIVEEQUIPMENT
Alwaysensureproperventilationanduseproperpersonalprotectiveequipmentsuchasgloves
andeyeprotectionwhenusingchemicals.RefertoMaterialSafetyDataSheetforspecific
requirementsofeachchemicalproduct.Takeallnecessaryprecautionstopreventsanitizerfrom
contactingeyes,clothing,andanyothersurfacesincoulddamage(carpets).

2. Put1teaspoonofsanitizerperdirectionsoruseBleachSolution(1teaspoon=1/6oz.=5ml=½
capfull)ofhouseholdbleach(SodiumHypochlorite5‐10%Concentration)intheSanitizing
Cartridge.Alwaysensuresanitizeriscompatiblewithstainlesssteelandacetylplastic.

3. Connectsanitizingcartridgetoinletwatersupplyandconnecttoinletbulkheadfittingonbackof
unit.Turnonwatersupply.

4. ConnectpowertoWL200.DONOTTURNONREDPOWERSWITCHATTHISTIME
O=OFF.





WL200Operating,Installation,andServiceManual Page13‐Revision:4‐13‐2016
FilltheColdCircuitwithSanitizer

5. Depressthemaindispensingbuttononthefrontcontrolpaneluntilcoldwater/sanitizingsolution
comesoutthefaucet.NOTE:Containeranddrainbasinwillberequiredtocatchthewaterfrom
thefaucet.

WARNING!UsePersonalProtectiveEquipment.GlovesandEyeProtectionRequired.Thefirst
2or3gallonsofwaterwillcontainconcentratedsanitizer.Useextremecare!

6. TurnoffwatersupplyandremoveSanitizingCartridgefrominletwatersupply.Reconnectwater
supplytoinletbulkheadfitting.


FlushFilters

CAUTION!FILTERFLUSHREQUIRED.

WL200’sarenotsuppliedwithfilters.Filtersshouldbeconfiguredtooptimizeyoursystem.Filters
needtobeconfiguredandspecifiedtodothejobgiventhelocalwaterconditions,usage,
maintenanceschedule,andplacementrestrictions.

Inorderforthefilterstoperformasrepresentedandtoprovidethebestqualitywaterpossible,it
isessentialthatfiltersbereplacedperiodically.Thefrequencyoffilterchangesdependsuponyour
waterqualityandyourwaterusage.Forexample,ifthereisalotofsedimentand/orparticlesin
yourwater,thenyouwillhavetochangeyourfiltersmorefrequentlythanalocationwithlittleto
nosediment.Besuretoreplaceyourfilterswheneveryounoticeadeclineintheperformance,
whetheritisadropinflowrateand/orpressureoranunusualtasteinthewater.

7. Flushthoroughlyperfiltermanufacturers’recommendationwithfreshwatertodrain.

8. Onceflushed,installthefilters.Followingtheflowdirectiononthefilter.

NOTE:
 Filtersshouldnotbeflushedpriorto24hoursbeforeinstallationtolimitMicrobial
Growth.

9. ConnectWL200topower.






WL200Operating,Installation,andServiceManual Page14‐Revision:4‐13‐2016
FlushingtheSanitizerfromtheMachine

10. Placeapitcher,catchbasin,orothercontainerunderthefaucetoftheWL200.

11. FlushtheColdTank.Runseveralgallonsofwaterthroughthefaucetbydispensingcoldwaterto
diluteandremovethesanitizerfromthecoldcircuit.Youcanusechlorineteststripstoevaluate
thewater.

12. Oncethesanitizerodor/tastehasbeenflushedoutofthecoldsideofthemachinethe
sanitizationprocessfortheColdCircuitisnowcomplete.



WL200Operating,Installation,andServiceManual Page15‐Revision:4‐13‐2016
WL200COUNTERTOPDRAININGINSTRUCTIONS

DrainingNotes

DraintheWL200fortransportation.

WARNING!STOREUNITEMPTY.ALWAYSSANITIZEBEFOREREUSE.
Theunitmustbecompletelydrainedandsealedbeforestoringtoavoidstagnationandreduce
microbialgrowth).


DisableColdTank

1. TurnofftheRedPowerSwitchtodisablecompressor.O=OFF

TurnoffWaterSupplyandBleedWaterPressure

2. Isolatetheunitfromfeedwaterbyturningoffthesupply.
3. Dispensecoldstillwatertorelieveanypressurebuiltupinthesystem.
4. Removethewatersupplylinefromtheinletlinebulkheadfittingatbackofmachine.
5. Installdustcaporplugintowatersupplylinebulkheadfitting.

DraintheColdWaterTankandCircuit

6. Removetopcover.


7. Removefrontpanel.Remove2Phillipscrews
securingfrontpanel.Unseatfaucetassembly
frompanel.UnclipwiresfromPCB.



WL200Operating,Installation,andServiceManual Page16‐Revision:4‐13‐2016
8. Disconnecttubingfrominletelbowfrom
solenoidandallowwatertodrain.


9. Reconnecttubingintoinletelbow,

10. Dryinsideofunit.


11. Replacefrontpanel.






WL200Operating,Installation,andServiceManual Page17‐Revision:4‐13‐2016
WL200TOWERDRAININGINSTRUCTIONS

DrainingNotes

DraintheWL200fortransportation.

WARNING!STOREUNITEMPTY.ALWAYSSANITIZEBEFOREREUSE.
Theunitmustbecompletelydrainedandsealedbeforestoringtoavoidstagnationandreduce
microbialgrowth).

DisableColdTanks

1. TurnofftheRedPowerSwitchtodisablethecompressor.O=OFF

TurnoffWaterSupplyandBleedWaterPressure

2. Isolatetheunitfromfeedwaterbyturningoffthesupply.
3. Dispensecoldstillwatertorelieveanypressurebuiltupinthesystem.
4. Removethewatersupplylinefromtheinletlinebulkheadfittingatbackofmachine.
5. Installdustcaporplugintowatersupplylinebulkheadfitting.

DraintheColdWaterTankandCircuit

6. Removelowerfrontpaneltoaccesstankfeedlines.

 

7. Disconnecttanklinefeedlinefromcoldinletsolenoidto
drainintobasinorcatch.

8. Reconnecttubingintoinletelbowoncedrained.


9. Dryinsideofunitifnecessary.


10. Replacelowerfrontpanel.




WL200Operating,Installation,andServiceManual Page18‐Revision:4‐13‐2016
INSTALLATIONPROCEDURES

SafetyandInstallationGuidelines
EnsureallLocal,State,andFederalLawsandCodesincludinghealthandsafetyguidelinesaremet
wheninstallingWaterlogicEquipment.Onlyqualifiedservicetechniciansshouldattempt
installationandserviceofWaterlogicEquipment.

WARNING!ELECTRICALSHOCKHAZARD.Alwaysunplug(isolatefrompowersupply)toprevent
electricalshockexceptwhereelectricaltestsarespecified.

WARNING!IMPROPERSUPPLYORCONNECTIONCANRESULTISRISKOFSHOCK.
Connecttoa15amp120V60Hzproperlygroundedoutlet(GFIisrecommended).Ensurepolarityis
correctandalwaysusea3‐prongoutlet.Consultaqualifiedelectricianifyouhaveanyquestions.

WARNING!USEONLYWaterlogicSUPPLIEDPOWERCORD.Locatesystemwithin5feetof
powersupply.Neveruseanextensioncordoradapter.Donotuseadamagedpowercordorplug.
Keeppowercordoutofheavytrafficareasandawayfromheatsources.Donot,underany
circumstances,removegroundprongoralterthepowercord.Neverpullthepowerplugfromthe
outletwithawethandorallowtheplugtogetwet.Failuretousethesuppliedpowercordwillvoid
ULCertificationandWarranty.

CAUTION!INDOORUSEONLY.Neverexposetodirectsunlight,heatsources,orambientair
temperatureabove100°F(37°C)orbelow35°F(2°C).Installindoorsandkeepunitawayfrom
excessivehumidity.Neverexposetofreezingtemperatures.Ensurethereisadequateclearance
aroundtheunittoallowrefrigerationsystemcondensertodissipateheat.Warmerenvironments
requiremoreclearancearoundtheunit.Minimumclearancearoundallsurfacesofthemachineis2‐
inches.Installswheretheambienttemperatureexceed80F,requireaminimumof4‐inchesclearance
forproperheatdissipationandefficientoperation.

CAUTION!USEAWATERPRESSUREREGULATOR.Waterlogicwillnotberesponsibleforinjuryor
damagecausedbyexcessivewaterpressure.Operatingpressuremustbe40psito60psi.Beaware
anyofpotentialpressuresurgescausedbybuilding/municipalpumpingstations.

CAUTION!USEUVSTABILIZEDSUPPLYLINES.Feedtheunitwithapotableambientorcold
watersupplyonly.Feedwaterover100°F(37°C)candamagethetreatmentcomponents.Water
blockdevicesandexternalleakdetectorsarestronglyrecommended.Locatetheunitasclosetothe
watersupplyandtheelectricalconnectionsaspossible.

WARNING!STOREANDTRANSPORTUNITEMPTY.ALWAYSSANITIZEBEFOREUSE.
Theunitmustbecompletelydrainedandsealedbeforestoringtoavoidstagnationandreduce
microbiologicalcontamination(potentialbacterialgrowth).Sanitizebeforeusetoeliminateany
potentialmicrobiologicalcontaminates 

Pre‐installationandsanitizationproceduresasprescribedinthismanualmustbeperformedbefore
installingtheWL200.

AlwaysinstallindoorsandplacetheWaterlogicWL200onafirm,flatandstablesurface.



WL200Operating,Installation,andServiceManual Page19‐Revision:4‐13‐2016

1. Attachthewatersupplylinetothe1/4”feedwaterinletbulkheadfittingonthebackoftheunit.
Waterlogicrequirestheuseofawaterpressureregulator.Waterfeedpressuremustbe
between40‐60psi.Turnonthewatersupplyandcheckforleaks. 


2. ChecktoensurethattheRedPowerSwitchisoff.O=OFF





3. ConnectthepowercordtothebackoftheWaterlogicWL200andtoa120Voltsupply.

4. FilltheColdTank.Holdacontainerunderthedispensingfaucet,pressandholdthemain
dispensingbuttonuntilacontinuousflowofwaterisobtained.Onceacontinuousflowis
obtained,releasethedispensingbutton.Coldtankisnowfull.

5. MovetheWaterlogicWL200intoitsfinaloperatingposition.Besurethataminimumof2”
clearanceismaintainedaroundboththesidesandthebackoftheunit.Thisisimportanttoallow
properairflowandheatexchangeofrefrigerationsystem.

6. Levelunitusingtheadjustablefeettolevelifnecessary.Neverinstallonincline.

7. TurntheRedPowerSwitchon.I=ON.






8. WhentheunithasreacheditsColdTempSetPointTemperature,thecompressorwillcycleoff.

9. Oncetheunitisatthetargettemperature(s),samplethewatertoensurewatermeets
expectationsandadditionalrinsingoradjustmentisnotrequired.


10. Checktheunitforanyleaks.ExternalLeakProtectionisalwaysrecommended.


WL200Operating,Installation,andServiceManual Page20‐Revision:4‐13‐2016
SERVICEREQUIREMENTS

WARNING!Readandunderstandthecontentsofthismanualbeforeattemptingtoservice
WL200.Failuretofollowtheinstructionsinthismanualcouldresultindeath,seriouspersonal
injury,orseverepropertydamage.Onlytrainedandqualifiedtechniciansshouldattemptto
install,maintain,orserviceWaterlogicEquipment.

1. Visuallyinspectallelectricalandwaterconnectionsforsignsofwearordamage.

DANGER!HIGHVOLTAGEELECTRICALHAZARD.Unplugbeforeinspectionandservice.

2. Ensurethereisadequate(minimumof2”)clearancearoundtheunitandcleanthecondensergrill
andcompressorfantoprovideefficientcoolingsystemoperation.

3. Sanitizethecoldtankperinstructionsinthepre‐installationprocedures.

4. Cleanandsanitizeexternalsurfacesoftheunit.Usesoapandwaterorchemicalsthatare
compatiblewithABSplasticandwillnotdamageordegradetheproductsurfaces.

5. RemoveandcleantheFaucet.Replaceasneeded.

WARNING!SANITIZERMAYCONTAINHAZARDOUSCHEMICALS.Useofproperpersonal
protectiveequipmentsuchasrubberglovesandeyeprotectionisrequired.

