WaterLogic escowa Purus iQ3 User manual

Purus i Q 3
S er v i c e - M anua l
For the I n s t a ll a t i on , Programming,
Cleaning a n d M a in t e n a n c e

This operating handbook relates to the following equipment:
Purus iQ 3
Type:
Serial number:
This service manual is for the installation, pro-
gramming, cleaning and maintenance. It is a part
of the equipment and must always be available
close by the machine, and always be available
up to the disposal of the equipment.
If you should loss or damage the manual, you
must request a replacement from the manu-
facturer or the local distributor. If you have any
questions please contact your local distributor.
Best Product
Design/Innovation
2

Chapter Page
Service Record 4
1. Machine Construction Overview
1.1 Dismantling 5
1.2 Inside front cover 6
1.3 View from rear 7
1.4 removal of covers 8
1.5 Internal View 9
1.6 view from top 10
2. General equipment information
2.1 Machine identification plate 11
2.2 Introduction and advice 11
2.3 Safety Information 12
2.4 Hazard Risk 12
2.5 Accessories 12
3. Installation Guide
3.1 Notes for Installation 13
3.2 General Functionality 13
3.3 Cleaning and Maintenance 13
3.4 HCCAP Record keeping 13
3.5 Recommendations for
first time installation of CO2,
and water connections 13
4. Installation
4.1 First installation 14
4.1.1 Preparation 14
4.1.2 CO2 Installation 15
4.1.3 Fitting the Water Filter 16
5. Sanitation and cleaning
5.1 Sanitation with Anolyte-sani-Brita
Service cartridge 17
5.1.1 Sanitation with the Service Cartridge. 17
5.2 Sanitation 18
5.2.1 Sanitation with iQ-sani-clean-SHOT
(using Anolyte) 18
5.3 Disinfection of Dispense area 19
5.4 Ozone Generator-Active Sanitation 19
5.5 Hygiene guidance 19
Chapter Page
6. Programming
6.1 To enter programming mode press
program Button (PT) for 6 seconds 20
7. Intended Use
7.1 Conditions 21
7.2 Operational basis 21
7.3 Advantages of the IQ3 21
7.4 Information on Accessories 22
8. Maintenance, cleaning and care
8.1 Cleaning Recommendation 22
8.2 Weekly disinfection cleaning 22
8.3 Sanitation 22
8.4 Taste filter (water filter) 22
8.5 General information on maintenance 22
8.6 Installation and service checklist 23
9. TechnicalData 24
10. WaterandCO2
10.1 Water supply 25
10.2 The Water filter 25
10.3 CO2 connection 25-26
10.4 CO2 of systems and connection 26
11. Troubleshooting
11.1 Troubleshooting guide 27
12. Schematics
12.1 Water Circuit 28
12.2 Wiring Diagram 28
Safety Markings 29-31
Notes 32-34
3

Service Record
Service
Equipment: IQ3
Nr.
Water Filter:
Inst. Date:
Technician:
Date
Counter
Work Carried Out
Technician
4

1. Machine Construction Overview
1.1 Dismantling
3
1
1. Display and Buttons
2. Aerator with filter
2 3. Drip tray with capacity
of 1.5 L
1
Chilled
Still Water
Sparkling Water
Ambient Water
Keypad Lock
3
5

1. Machine Construction Overview
1.2 Inside front cover
1 2
1
4 2
3
1. Connection for external 4 3
CO2 bottle
2. Aerator
(change every 12 months)
3. BRITA filter
4. Disposable CO2 bottle
(optional)
6

1.3 View from rear
1
5
4
2
3 7
6
3
1
2
1. External CO2 connection 5 4
2. Mains water inlet
3. Power supply connection
4. Programming button
5. Programming card slot
6. Machine
identification plate
7. Evaporator
7

1. Machine construction overview
1.4 removal of covers
1 1
2
1. Undo top cover screws
2. Remove top cover first
3. Remove side covers
3 3
3
8

1.5 Internal View
1
3
2
4
1
2
Left Side view
5
4
7 6
5
6 8
Right Side view
1. High pressure pump
2. Compressor (Time out 4 h)
3. Carbonator
4. PCB Cover
5. Ozone Generator 8
6. High pressure pump
7. Cooling fan
8. Inlet valve
9

1. Machine construction overview
1.6 view from top
1. Thermostat
2. Relief valve (7.5 bar)
3. Level probes
4. Outlet valves
3
2
1
4
5. CO2 water
6. Chilled Still water
5 7. Ambient still water
6 8. Ozone injector
7
8
10

2. General equipment information
2.1 Machine identification plate
The machine identification plate contains impor-
tant information. Please always indicate type of
device and serial number for spare part orders.
2.2 Introduction and advice
• Before installation of the equipment,
please read the operating instructions
carefully.
• The correct use of the equipment
depends exclusively on the user.
• Correct functionality of the equipment is
guaranteed only when genuine spare parts
are used.
• Installation, setup and repair of the equip-
ment must only be carried out by a trained
engineer.
The manufacturer is not responsible for
damage to the equipment caused by:
• Neglect to follow the guidelines in
this manual.
• Repairs which are not carried out by
an authorised engineer.
• Recalibration, change and inappropriate
use (including connection to none drinking
water supply).
The machine identification plate shows
the following detail:
OEM: Manufactor
Model/type of device: E-iQ3-E-3
sparkling+ozono
Model number: 010124/0005
Voltage / Current: 220/230VAC 50Hz 0.84 A
Cooling agent: Refrigerant:R134a (40gr)
Max. Inlet water
pressure: 5 bar
Max CO2 pressure: 6 bar
Manufacturing country: Made in Italy
11

2. General equipment information
2.3 Safety Information
This equipment is manufactured with consi-
deration to safety aspects. Regardless this
equipment must only be serviced by authorised
persons. Repair and servicing must be carried
out only by trained technicians who are experi-
enced with the equipment or similar devices to
recognise and prevent any faults that may
cause injury.
These operating instructions must be read in
there entirety prior to installing the equipment to
ensure a safe installation and perfect operation
of the equipment.
Attention:
Remove the power supply to the equipment
before removing any covers. The equipment
is developed in accordance with the following
European safety certifications:
- EN 60335-2-24:2003 + A11:2004 + A1:2005
+ A2:2007
”Safety of the electrical household appliances
and similar devices”.
2.4 Hazard Risk
Please take into account local legal requirements
with regards to installation and use of CO2 com-
pressed gas. Do not submerge the equipment in
water. Always disconnect from the mains power
supply when cleaning the equipment.
Never allow children to operate the equip-
ment unsupervised.
2.5 Accessories
Various accessories are available for the equip-
ment. where accessories are in the form of kits
they will be supplied with instructions, which
must be adhered too in order to maintain the
safety of the equipment.
• IQ3 pressure regulator for disposable
• CO2 600 gr bottle.
• IQ3 Commercial 10 kg CO2 regulator
• IQ3 CO2 disposable 600 gr. bottle
• IQ3 200 ml disposable cups
• IQ3 300 ml disposable cups
• IQ3 Glass Decanter 0.7 L
• IQ3 Plastic sports bottle 1.0 L
• IQ3 1.4 L plastic jug
• IQ3 Disinfection Spray
• IQ3 Sanitation Kit
• IQ3 Water Meter
• IQ3 Water Filter
12

3. Installation Guide
3.1 Notes for Installation
• Read the manual carefully before using the iQ3.
• The mains water supply must be potable
(safe for drinking).
• The iQ3 should always be connect to a
mains electricity supply.
• Do not touch for hygiene reasons the
water dispense nozzle.
• Use only original manufacturer
supplied spare parts.
3.2 General Functionality
The iQ3 can produce the water in 3 different
ways. Selection 1 Filtered water at ambient
temperature
Selection 2 Chilled filtered water
Selection 3 Chilled carbonated filtered water
The temperature and the amount of carbonation
of the water can be adjusted.
3.3 Cleaning and Maintenance
Before carrying out any cleaning and mainte-
nance work make sure that the power supply
is disconnected.
For cleaning the external areas of the iQ3
use a damp, lint free cloth.
3.4 HCCAP Record keeping
Ensure that HCCAP records are kept where
applicable.
3.5 Recommendations for first time
installation of CO2, and water
connections.
The installation of the equipment may must
be carried out by a trained technician.
The installation must follow this sequence:
Gas, water, electricity (GWE).
13

4. Installation
4.1 First installation
4.1.1 Preparation
Attach the CO2 gas supply before flushing the filter.
See details on the following page.
3 1
2
4
1. Connect the mains water supply to the iQ3. Do not turn 5
the water supply on. Do not attach the mains cable.
2. Remove the drip tray
3. Remove the front cover
4. Installation positions of a CO2 disposable bottle,
and the BRITA water filter.
5. The accessories provided: Water connection kit,
mains power cable.
14

4.1.2 CO2 Installation
Before installing the CO2 the BRITA C1000AC must first be
fitted and flushed. See details on the following page. Disposable or commercialCO2
1 2
3 4
5
1. The equipment is supplied with a 4 mm CO2 inlet hose. The 6
hose is suitable for the disposable CO2 system. For more
details on CO2 and valves please refer to later chapter.
2. Ensure that the pressure regulator valve is OFF (closed)
and connect the valve to the disposable CO2 bottle, then
attach the 4 mm hose to the push fit on the valve. Mount the
bottle in the bracket at the front of the equipment. Cut the
hose to the required length and connect to the push fit
connector at the front of the equipment. Leave the CO2
regulator closed.
3. Alternatively for commercial 6/10 kg CO2 bottles, connect
link pipe to the push fit connector at the front. The external
CO2 bottle is then connected at the 4 mm push fit
connector at the rear of the equipment.
4. Ensure that commercial bottle regulating valve is OFF(closed)
5. Fit the commercial bottle regulating valve as described in
the later chapter regarding CO2 bottles and valves.
Leave the CO2 regulator closed.
6. make sure the CO2 bottle is secured and in a safe position.
Consider the CO2 handling legal regulations.
15

4. Installation
4.1 First Installation
4.1.3 Fitting the Water Filter
1 2
3
4
1. Fit the C1000AC cartridge with the bayonet fixing to the 5
filter head.
2. Push the Cartridge upwards in correct position. Lock the
cartridge with the blue lever. Open the mains water supply.
Check the water connection for leaks.
3. Connect the equipment to the mains power supply.
4. Press the Ambient water button and dispense 1 L of water
to flush the filter. Then press the Sparkling water button
briefly the pump will now run for a short time to fill the
carbonator.
5. Refit the front cover, the equipment is ready for use.
Please allow some time for the temperature to reach
the programmed value.
16

5. Sanitation and cleaning.
5.1 Sanitation with Anolyte-sani-Brita Service cartridge.
5.1.1 Sanitation with the Service Cartridge.
Sanitation should be carried out at installation and at 6 monthly intervals.
1
2
3
1. Turn off Water Supply. Press the button for ambient water for 3
10 sec, then press the button for Cool water for 10 sec. Now
press the sparkling water button, keep pressed until the
water stops and only CO2 gas is dispensed. Close the CO2
regula- tor valve, press the Sparkling water button again to
release the gas pressure. Now switch equipment power
supply off.
2. Lead the grey hose of the filter head into a container and
press the grey button on the filter head to release the
pres- sure in filter.
3. Place the cleaning agent in the special service cartridge.
4. Remove the filter Brita C1000cartridge. and replace with the
Service Cartridge. 4
5. Place a container under the discharge. Press the key still
chilled water button until the water turns blue in colour.
Press ambient water button, untilthe water turns blue in
colour,
use a indikator to check. Press the button for sparkling water
briefly so the pump starts, wait for the pump to stop
(carbona- tor full), press and hold the sparkling water button
until water turns blue in Colour.
6. Wait for 20 mins. so that the solution can activate. 5
7. Remove the service cartridge and refit the Purity1000 filter
(if necessary renew the filter if Service life or capacity
is reached).
8. Rinse water through each button chilled, ambient and
spar- kling until water runs clear through each selection.
Examine the pH value (acidity). Still= 6.5 - 7.0, Sparkling =
6 -6.5
9. Open the CO2 regulator valve and dispense 2 L
sparkling water to re-carbonate.
10. Fill out the service record.
17

5. Sanitation and cleaning
5.2 Sanitation
5.2.1 Sanitation with iQ-sani-clean-SHOT
(using Anolyte)
Alternative Cleaning option.
1. Fit the Anolyte kit (injector and bottle with 1 L concentrate)
instructions are included with the kit. The kit is fitted
externally between the water supply and intake valve of the
equipment.
2. Remove the Brita filter from the filter head and dispose.
3. Rinse from all 3 selections 5 L for each.
4. Turn OFF the mains water supply and hold button 1 spar-
kling water until all water is dispensed and only CO2 gas is
dispensed. Now turn off the CO2 supply at the regulator.
5. Turn the lever on the injector to “caustic solution“ and turn
ON the mains water supply.
6. Dispense 200 ml using button 3 ambient water.
7. Dispense 300 ml using button 2 chilled water
8. Briefly press button 1 Sparking water. The pump will start
and fill the carbonator.
9. When the pump stops press button 1 sparkling water and
dispense 500 ml of water. turn the injector lever to „water“.
10.Allow 30 minutes for the internal components to soak.
(The kit can be dismounted meanwhile or left in place for
next time)
11.Rinse after the soak period, 5 L using button 3, 5 L using
button 2, and 10 L using button 3.
12.Turn the main water supply Off and turn On the CO2. Hold
button 1 sparkling water until all water is dispensed and
only CO2 gas is dispensed. Now turn the Water supply on
and allow the carbonator to refill.
13.Fit a new Brita C1000 filter and flush with 1 L using
button 3 Ambient water.
Note:
10 L of chilled sparkling water should be dispensed to rinse
the carbonator, to be sure that the Anolyte is rinsed from
the system. alternativley us PH indicator strips to make sure
PH level is neutral.
The Anolyte cotains: sodium hypochlorite and
hypochlorous acid.
Chilled
Still Water
Sparkling Water
Ambient Water
18

5.3 Disinfection of Dispense area
Disinfect after maintenance the dis-
pense area with disinfection spray
around to ensure perfect hygiene.
Appoint a responsible person to
carry out cleaning at least once a
week, daily in hygiene sensitive
environment.
Proceed here as follows:
• Clean the entire dispense area with a
disin- fectant.
• Remove and clean the drip tray with
disinfec- tant, make sure the drip tray is
completely
dry before replacing it.
• Spray the outlet nozzle outside and inside
from beneath with disinfection spray. leave
for 5 minute to soak.
• Run 1 litre of water using the ambient
water button to rinse the disinfectant from
the nozzle.
• Wait for approx. 30 minutes until the
cooling the temperature of 4°C-8°C
reached.
• Make sure that the responsible person on
site is familiar with this cleaning procedure.
5.4 Ozone Generator - Active Sanitation
Ozone Sanitation - after every
dispense a small quantity of
O3 (Ozone) is injected into
dispense valves, dispense
pipes and nozzle. Ozone acts
on and destroys bacteria. The
Ozone generator will activated every 30 minutes
and after every dispense.
Examination:
Every 2 years the Ozone generator should be
inspected to ensure its effectiveness (a simple
test is to smell for the Ozone).
The equipment is built in a hygienically germ-
free production facility. To ensure that the hygie-
ne remains as intended make sure that cleaning
instructions are adhered too. Use our pollution
free and highly effective disinfection spray.
Cleaning and disinfection procedure:
1. Clean the entire dispense area with
a disinfectant.
2. Remove the drip tray and empty.
3. Clean the drip tray with disinfectant, rinse
and dry before replacing.
4. Spray the outlet nozzle outside and inside
from beneath with disinfection spray. leave
for 5 minute to soak.
5. Run 1 litre of water into a jug using the ambi-
ent water button to rinse the disinfectant from
the nozzle.
6. Clean the exterior of the equipment with a
damp cloth. Before cleaning press the far
right hand service button for 10 seconds the
will lock the other buttons to prevent acciden-
tal dispense while cleaning. After cleaning,
press the service button again for 10 seconds
to enable the dispense buttons.
6
4 1
5.5 Hygiene guidance
Hygiene guidance and hygiene references for
the user. A careful HYGIENE is the basic con-
dition for beverage quality and long life span of
the iQ3. A rigourous hygiene routine ensures a 2
reliable, continuous use, a fresher drink supply
and a multitude of highly pleased users over the 3
entire Life span of your water machine.
19

B
a
6. Programming
6.1 To enter programming mode press program Button (PT) for 6 seconds.
Program Button (PT)
T1 - T2 +
uttons used to change
nd store values.
Press PT to scroll through the options.
Default setting
Options
Refrigerator Temp
(PT)
Refrigerator temperature +8.0
T1 to decrease T2
to increase Range
4.0-6.0-8.0
Energy Saving
(PT)
Energy Saving Mode 00
00 Normal
01 Button + LED dimmed
02 Button, LED and display dim-
med. When a button is pressed
the display will light.
Enable Tones
(PT)
Tones ON
ON or OFF
ECO Reset KG
(PT)
CO2 saving counter
Press T1 and T2 together to reset.
Power Ozone
(PT)
00 Ozone generator Off.
01 Ozone generator runs for
200 ms after each dispense.
02 Ozone generator runs for
400 ms after each dispense.
03 to 05 Ozone generator runs for
600-1000 ms after each dispense.
Software version
(PT)
V4.1 N F04 k00 Cv 000000 g
00000 V4.1
Software Version
F04 Brita Filter Purity 1000
K00. CV 00000 Custom ID field.
G 00000 Number of days active.
Save Settings
(PT)
Press T1 and T2 together to save
Exit Programming Mode
Remove mains power for 5s
20