WaterLogic Water Filtration Systems User manual

THE HYBRID SERVICE GUIDE
Watch the video online:
www.waterlogicfirewall.com/
products-hybrid-water-purifier/
F-FWEG1-M-A-NT-**-***
Warning: Boil the water
should the purification unit fail

1.1 Remove the items from the box. Hold the
UV lamp by the plastic edges, and avoid
touching the glass parts as this may
affect the performance of the lamp
1.2 Please check the contents of the box and
make sure that all items are present
1.3 If any of the items are missing please
contact customer service
REPLACEMENT UV LAMP
REPLACEMENT FILTER
A
B
A
B
1. PURE KIT CONTENTS
2. UV BULB AND FILTER REPLACEMENT
IMPORTANT - UNPLUG THE APPLIANCE
FROM THE MAINS BEFORE REPLACING
THE UV LAMP OR FILTER
THE WATERLOGIC HYBRID IS A HIGH PERFORMANCE WATER PURIFIER, KEEPING IT IN GOOD
WORKING ORDER WILL PROVIDE THE REASSURANCE OF TRULY GREAT DRINKING WATER
• The UV Bulb and Filter must be
replaced every 12 months to ensure
that your appliance is dispensing the
highest quality drinking water.
Replacement Parts:
Please make sure you use only original
Waterlogic replacement parts. If you
are not sure which replacement parts
to use, please consult with your local
Waterlogic retailer or distributor

3
2 .1 Remove the water reservoir from the
main body of the appliance. This can
be cleaned with a light solution of
dishwashing liquid. Never use abrasive
chemicals or materials to clean the
reservoir as this could scratch and
deface the product
2.2 Remove the two screws that hold the
top cover in place. You will need to use
a screwdriver to carry out step 2.2
2.3 Remove the top cover from the unit by
slightly pushing it back and then lifting it up

2.4 Disconnect the UV lamp connector by
holding it and pressing in the clip on the
connector and pulling it up
2.5 To remove the UV lamp firmly pull it up
and out. Do not pull the lamp out at an
angle as it may break or damage the
internal parts of the appliance
Note: The UV lamp must be disposed
of correctly and must not be disposed
of with normal household waste
2.6 Insert the new UV lamp while holding the
white end caps only. Insert the UV lamp
as shown in the illustration and push it all
the way down until it cannot go
any further
CAUTION
:- Do not use force when removing and
inserting the UV lamp as you may
damage internal parts
:- Do not touch the UV lamp glass
surface with your fingers as this
will affect the performance of the
UV lamp

5
2.7 Re-connect the UV lamp connector
making sure the connectors are lined
up correctly as they will only fit together
when correctly aligned
2.8 To remove the Filter, do the following:
1. Rotate the red rotating lever so that it is parallel
with the side panel
2. Insert your finger into the round hole of the
lever, and pull the lever up to the
vertical position
3. Pull the lever straight up to remove
the Filter assembly (Slight force may
be required. Support the unit with
your other hand while pulling the
filter out).
Note: Dispose of the filter
following your local guidelines
1. 2. 3.
2.9 Fit the new filter assembly into the
appliance as follows:
1. Insert the filter assembly back into
its cradle, aligning the two male spigots
with the female holes in the cradle
2. Push firmly until the filter sits snugly
and is flush inside the cradle and with
the cradle top surface
3. Lock the filter by closing the locking
lever until it ‘clicks’ into place
4. Rotate the red rotating lever back into
the LOCK position
1.
2.
3.

2 .10 Re-fit the top cover, making sure the
front is attached first. If the top cover
is not fitted correctly the unit will
not switch on
Hint: Fit the top cover making sure the
front is pushed in place first and then
push the back end with the screws
down to give a snug fit
2 .11 Re-fit the two screws that hold
the lid down using a screwdriver.
Caution: The screws should be hand
tightened, do not over tighten
Insert the plug into the mains socket.
2 .12 Press and hold the dispense button for
10 seconds until you hear a beep as this
will rest the filter timer
Note: Place a cup or container under
the dispense area before carrying out
step 2 .12
2 .13 Rinse the reservoir and then fill the
reservoir from a potable water source.
Do not overfill the reservoir. Re-fit the
reservoir lid

7
2 .14 Re-fit the reservoir to the appliance
making sure it is firmly fitted
2 .15 Place a glass or large container under the
dispense area and touch the dispense button
to operate the unit, and touch again to stop the
appliance. Allow water to run through the unit
until the reservoir has been emptied.
Note: Do not consume the water
until step 2 .17 has been completed.
The first 3-5 litres of water dispensed may
contain some fine, black carbon particles.
Carbon is a natural, organic material made
from coconut shell, and is harmless to your
health. Clear water should be noticed after
flushing through 3 to 5 litres of water (2 to 3
full reservoirs). Do not allow the water level in
the reservoir to drop below the minimum fill
line, as when the reservoir is completely empty
the pump will begin to suck in air and make
bubbling noises.
2 .16 Remove the water reservoir from the
main body of the appliance and remove
the lid from the reservoir

2 .17 Repeat steps 2 .13 - 2 .16 three to four
times (3x - 4x). This will flush the carbon
from the new filter
2 .18 Once step 2 .17 has been completed
you can drink purified, healthy and safe
water from your appliance
During the first week of use and after
every filter change you may notice water
dripping out of the dispensing-nozzle
for several seconds after the unit has
stopped dispensing. This is normal,
and will stop after several days of use.
Note: For a cold refreshing drink the
reservoir may be stored full of water
in the fridge
x3-4

9
3. CLEANING
It is recommended that you maintain your appliance by cleaning it on a regular basis.
The appliance can be cleaned using a damp lint free cloth. Never use any alcohol or alcohol
based chemicals or abrasive materials on any part of the product.
4. STORAGE
Do not store the Pure Kit in damp conditions, or anywhere that it could get wet.

5. SAFETY
6. DISPOSAL
• Do not touch or look directly into
the faucet
• Do not handle or lift the appliance by
holding the reservoir
• Only authorised trained technicians may
carry out repairs on this appliance
• The filter and UV lamp must be replaced
every 12 months.
• The user may only replace the filter and
UV lamp
• Never use any chemicals or abrasive
materials on any part of the product
• Should a fault occur on the appliance
always unplug it from the mains
power supply
• If the power lead is damaged in any way
it must be replaced by an authorised
dealer or qualified person
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety
• Children should be supervised
to ensure that they do not play
with the appliance
Do not dispose of the UV lamp and filter
with normal household waste, hand it in
at an official collection point for recycling.
By doing this you are doing your bit for the
environment. WEEE compliance
Manufactured by Qingdao Waterlogic Manufacturing Co., Ltd
No 10 Jinling Road, Jinling Industrial Zone, Chengyang District, Qingdao, 266111, Shandong, P.R. CHINA
TEL: [phone]
10
This marking indicates that this product should not be
disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the
return and collection systems or contact the retailer where
the product was purchased. They can take this product for
environmental safe recycling.
Correct Disposal of this product
15052014v09