WB Manufacturing EPIC EPC-FX User manual

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
1
Step 1:
• Place EPIC frame leg with plate facing down on a flat surface.
Step 2:
• Align holes in the end plate of the cross bar with the frame.
Make sure the tabs on the cross bar are facing down.
• Connect cross bar to the frame using ⁄”-20 x 50mm joint
connector bolts and ⁄”-20 joint connector nuts.
• Use a screw gun and a 4mm hex bit to tighten the joint
connector bolts to the nut. We suggest using a 4mm hex
wrench to hold the nut in place while tightening the bolt.
• Repeat for other frame leg.
Step 3:
• Place the EPIC top face down on a protected flat surface so
threaded inserts (marked in green) and pre-drilled pilot holes
(marked in yellow) are facing up.
Step 4:
• Place frame leg/cross bar on the top and align with threaded
inserts & pre-drilled pilot holes.
• Using a screw gun and a 4mm hex bit, secure both frame
legs to top with ⁄”-20 x 15mm joint connector bolts. Use
eight bolts for each frame leg.
Step 5:
• Using a screw gun and a # S2 square bit, secure cross bar
to top with #10 x ⁄” square pan screws. Use one screw per
tab with a total of six screws being used (3 per side).
Step 6:
• Before placing caster in the bottom of the frame leg, lock the
caster by pushing down on the brake lever.
• Twist the stem of the caster into the hole on the bottom of
the leg frame.
• Use 1⁄” socket wrench to tighten ⁄” nut on stem of caster.
• Repeat for remaining casters.
Step 7:
• With someone’s help, turn table upright.
Before you begin, please make sure all parts and proper
quantities are included. (See Part Identifier Key) Any parts
damaged during shipment must be reported within 24 hours of
receipt. To report information regarding damages or if you have
any questions, please call 800.242.2303.
EPIC Tables
Laminate/Phenolic/Stainless Steel
& 1 Pc Hardwood Tops
Assembly Instructions
Step 7
EPIC frame leg
Step 1 Step 2
Cross bar
Ta b
Joint connector bolt
Joint connector nut
Step 6
Step 4Step 5
Step 3
V121721 Version subject to change
NOTE: Casters are not to be used as a leveling device.
Loctite on casters will cause some resistance while
tightening, please make sure that casters are tightened all
the way to prevent possible damage to the stem of the caster.
Tools Required
• Screw gun
• # S2 square bit
• 4mm hex bit
• 4mm hex wrench
• 1⁄” socket wrench

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
2
Assembly Instructions
Part # Description Qty.
04067960 ⁄”-20 x 50mm joint connector bolts 2 per leg frame (4 total)
04009022 ⁄”-20 joint connector nuts
(Used to attach cross bar to leg frame) 2 per leg frame (4 total)
04009023 ⁄”-20 x 15mm joint connector bolts
(Used to attach leg plates to top) 8 per leg plate (16 total)
0408231 #10 x ⁄” Square pan screw
(Used to attach cross bar to top) 3 per side of the cross bar (6 total)
0400993 3” heavy duty locking casters 1 per leg (4 total)
Part Identifier Key
Model # Sku # Description
EPC -FX 04067852 EPIC fixed frame leg w/3” heavy duty locking casters
EPC -WFX 04067853 EPIC fixed frame leg w/3” heavy duty locking casters
EPC -SFX 04067854 EPIC fixed frame leg w/3” heavy duty locking casters
EPIC Frame Legs
EPIC Tables
Laminate/Phenolic/Stainless Steel
& 1 Pc Hardwood Tops