WB Manufacturing EPIC User manual

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
1
EPIC Tables
2 Pc Hardwood Tops
Assembly Instructions
Tools Required
• Screw gun
• # S2 square bit
• 4mm hex bit
• 4mm hex wrench
• 1⁄” socket wrench
⁄” wrench
Before you begin, please make sure all parts and proper
quantities are included. (See Part Identifier Key) Any parts
damaged during shipment must be reported within 24 hours of
receipt. To report information regarding damages or if you have
any questions, please call 800.242.2303.
Step 1:
• If assembling a hardwood top that has a depth greater than 36”, top
will be in 2 pieces (0.5” undersized on length). Place both top halves
face down on a protected flat surface. Align the dog bone holes
together on both tops.
Step 2:
• Adjust tite joint fastener to the size of the field joint opening and
then place the fastener into each opening. Using a ⁄” wrench,
tighten each fastener so that both tops are securely clamped
together.
Qty N/A
Tite joint fastener
Dog bone holes
Tite joint
fastener
V022122 Version subject to change

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
2
EPIC Tables
2 Pc Hardwood Tops
Assembly Instructions
Step 3:
• Place EPIC frame leg with plate facing down on the bottom of the
top.
• Place adjustable cross bar down on the bottom of the top.
Step 4:
• Align holes in the end plate of the cross bar with the frame, with
the tabs on the cross bar facing down.
• Connect cross bar to the frame using (2) ⁄”-20x50mm joint
connector bolts and (2) ⁄”-20 joint connector nuts.
• Use a screw gun and a 4mm hex bit to tighten the joint connector
bolts to the nut. We suggest using a 4mm hex wrench to hold the
nut in place while tightening the bolt.
• Repeat for other frame leg.
EPIC frame
leg plate
Cross bar
End plate of
cross bar
Cross bar
End plate of
cross bar
(hidden in
image)
EPIC frame
leg plate
Qty 4
⁄"-20x50mm joint connector bolt
Qty 4
⁄"-20 joint connector nut

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
3
EPIC Tables
2 Pc Hardwood Tops
Assembly Instructions
Qty 16
⁄"-20x15mm joint connector bolt w/ Loctite
Step 5:
• Align the assembled frame with threaded inserts & pre-drilled
pilot holes in the bottom of the top.
• Using a screw gun and a 4mm hex bit, secure both frame legs to
top with ⁄”-20 x 15mm joint connector bolts. Use (8) bolts for
each frame leg.
EPIC frame
leg plate
Step 6:
• Using a screw gun and a # S2 square bit, secure cross bar to top
with #10 x ⁄” square pan screws. Use one screw per tab with a
total of six screws being used (3 per side).
Qty 6
#10 x ⁄” square pan screw
Cross bar

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
4
EPIC Tables
2 Pc Hardwood Tops
Assembly Instructions
Step 8:
• With the help of another person, turn table to the upright position.
Step 7:
• Before placing caster in the bottom of the frame leg, lock the
caster by pushing down on the brake lever.
• Twist the stem of the caster into the hole on the bottom of the
leg frame.
• Use 1⁄” socket wrench to tighten ⁄” nut on stem of caster.
• Repeat for remaining casters.
UNLOCKED LOCKED
NOTE: Casters are not to be used as a
leveling device. Loctite on casters will cause
some resistance while tightening. Please
make sure that casters are tightened all the
way to prevent possible damage to the stem
of the caster.
Leg
frame
Caster

wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
5
EPIC Tables
2 Pc Hardwood Tops
Assembly Instructions
Part Identifier Key
Model # Sku # Description
EPC -FX 04067852 EPIC fixed frame leg w/3” heavy duty locking casters
EPC -WFX 04067853 EPIC fixed frame leg w/3” heavy duty locking casters
EPC -SFX 04067854 EPIC fixed frame leg w/3” heavy duty locking casters
Step # Part # Description Qty.
Step 1 0406902 Tite joint fasteners # depends on top size
Step 4 04067960 ⁄”-20 x 50mm joint connector bolts 2 per leg frame (4 total)
Step 4 04009022 ⁄”-20 joint connector nuts 2 per leg frame (4 total)
Step 5 04009023 ⁄”-20 x 15mm joint connector bolts 8 per leg plate (16 total)
Step 6 0408231 #10 x ⁄” Square pan screw 3 per side of the cross bar
(6 total)
Step 7 0400993 3” heavy duty locking casters 1 per leg (4 total)
Step 3
04067855 OR
04068252
34-64” Adjustable cross bar OR
46-64” Adjustable cross bar
(Item number depends on the size of top.)
1