WB Manufacturing Ingenuity EPIC User manual

Ingenuity EPIC Table
Assembly Instructions
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
1
EPIC frame leg
Step 1
Step 2
Cross bar
Ta b
Joint connector bolt
Joint connector nut
Step 3
Step 4
Step 5
Tools Required
• Screw gun
• # S2 square bit
• 4mm hex bit
• 4mm hex wrench
• ⁄” wrench
Before you begin, please make sure all parts and proper
quantities are included. (See Part Identifier Key) Any parts
damaged during shipment must be reported within 24 hours of
receipt. To report information regarding damages or if you have
any questions, please call 800.242.2303.
V032922 Version subject to change
Step 1:
• Place the EPIC frame leg with plate facing down on a
protected flat surface.
Step 2:
• Align holes in the end plate of the cross bar with the
frame. Make sure the tabs on the cross bar are facing
down.
• Connect cross bar to the frame using ⁄”-20 x 45mm
joint connector bolts and ⁄”-20 joint connector nuts.
• Use a screw gun and a 4mm hex bit to tighten the
joint connector bolts to the nut. We suggest using
a 4mm hex wrench to hold the nut in place while
tightening the bolt.
• Repeat for other frame leg.
Step 3:
• Place the top face down on a protected flat surface so
threaded inserts and pre-drilled pilot holes are facing
up.
Step 4:
• Place frame leg/cross bar on the top and align with
threaded inserts & pre-drilled pilot holes.
• Using a screw gun and a 4mm hex bit, secure both
frame legs to top with ⁄”-20 x 15mm joint connector
bolts. Use (8) bolts for each frame leg.
Step 5:
• Using a screw gun and a # S2 square bit, secure
cross bar to top with #10 x ⁄” square pan screws.
Use one screw per tab with a total of (6) screws being
used (3 per side).

Ingenuity EPIC Table
Assembly Instructions
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
2
Step 6:
• Before placing caster in the bottom of the frame leg,
lock the caster by pushing down on the brake lever.
• Twist the stem of the caster into the hole on the
bottom of the leg frame.
• Use ⁄” wrench to tighten ⁄” nut on stem of caster.
• Repeat for remaining casters.
Step 7:
• Turn table to the upright position with the help of
another person.
Step 8:
• Align pre-drilled holes in one of the long laminate rails
with the threaded inserts in the side of the top.
• Using a ⁄”-20x40mm joint connector bolt, insert the
bolt through the pre-drilled hole in the rail into the
threaded insert of the top. Use a 4mm Allen wrench
or a 4mm hex bit and a screw gun to fasten bolt into
place.
• After the first bolt is fastened, proceed attaching the
remaining bolts in the long rail.
• Repeat Step 8 for the remaining three rails.
Step 6
Step 7
Step 8

Ingenuity EPIC Table
Assembly Instructions
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
3
Model # Sku # EPIC Frame Leg Description
EPC -FX 04067852 EPIC fixed frame leg w/3” heavy duty locking casters
EPC -WFX 04067853 EPIC fixed frame leg w/3” heavy duty locking casters
EPC -SFX 04067854 EPIC fixed frame leg w/3” heavy duty locking casters
04067855 04067855 EPIC Frame Adj. Cross Bar 34”- 64”
EPIC Frame Legs and Adj Cross Bar
Standard Frame Color
09
Part Identifier Key
Additional Colors for EPIC frames
B
Blue
G
Green
O
Orange
P
Purple
R
Red Black
09
Smooth
Silver
G4
Black
09
Step # Part # Description Qty.
Step 2 N/A ⁄”-20 x 45mm joint connector bolts 2 per leg frame (4 total)
Step 2 04009022 ⁄”-20 joint connector nuts 2 per leg frame (4 total)
Step 4 04009023 ⁄”-20 x 15mm joint connector bolts 8 per leg plate (16 total)
Step 5 0408231 #10 x ⁄” Square pan screw 3 per side of the cross bar (6 total)
Step 6 0400993 3” heavy duty locking casters 1 per leg (4 total)
Step 8 0406526 ⁄”-20 x 40mm joint connector bolts 16