WB Manufacturing UNE-T7142-ADJ User manual

1
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
1-800-242-2303
wibenchmfg.com
UNE-T DESK/TABLE
PARTS
NOTE: These instructions are based on model
#UNE-T7142-ADJ. These instructions work for
all UNET desk & table models. Product images
are for illustrative purposes only and may differ
from actual product.
V042822 Version subject to change
The assembly of this desk requires the
assistance of another person.
TOOLS NEEDED
Drill 4mm Allen
Wrench
4mm Hex
Bit
Assistance
HARDWARE x QTY
⁄”-20x19mm joint connector
bolts x 6 per leg plate
04088861
#12 star lock washer
0404281
UNE-T connector bar (adj. or
non-adjustable)
04009770 (27”L top size)
fixed bar
04009771 (36”L top size)
fixed bar
04009772-G4 (48”L top size)
fixed bar
04009773 (54”L top size)
fixed bar
04077747-G4 (27”, 30” &
36”L top sizes) adj. bar
04066970 (27”-44”L top
size) adj. bar
04066939 (38”-66”L top
size) adj. bar
M6-1x10mm button head
socket screw x 4 (Used to
attach non-adj cross bar)
04067356
M6-1x14mm button head
socket screw x 2
0401259 (Used to attach adj
cross bar)
1.38” nylon glide
NSL-33056
PARTS x QTY
# DESCRIPTION x QTY
1 Laminate Top x 1
2 Leg x 2
3 Leg Plate x 2 (Attached to Leg)
4 Cross Bar x 1
5 Footing x 4
6 Backpack Hook x 1 (Optional)





Phillips
Screwdriver
14mm
Wrench

2
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
OPTIONAL HARDWARE x QTY
CAUTION! Some parts may have sharp
edges. Care must be taken when handling
various pieces to avoid injury. For your safety,
wear a pair of work gloves when assembling.
NOTE: Hardware packs are included in
packaging. You may receive more hardware
than needed. Discard any extra hardware after
assembly.
PARTS
2.5” Grand Hank nylon
glide, ⁄”-16x1” x 1 per leg
040164
1.5” soft touch glide x 1 per leg
04067920
1.25” steel glide x 1 per leg
NSL-33056S
Dual wheel soft tread locking
caster x 1 per leg
04067540
Backpack hook x 1
04066852 (black)
04066852-G4 (smooth silver)
⁄”-20x19mm joint connector
bolt x 1
04088861
Metal wire management x 1
04009316 (36”L)
04009242 (48”L)
04009241 (60”L)
0400350 (72”L)
UNE-T foot rest x 1
04066605
#8x3/4” screws x 10
0404248
2 ⁄”D black grommet w/
cover x 1 - 48”L top or
x 2 - 60” & 72”L tops
0406659

3
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
ASSEMBLY
1. Place top  face down on protected flat surface so
that the threaded inserts are facing up.
2. Align leg plates  (attached to legs ) with
threaded inserts in the top .
Using a 4mm Allen wrench or 4mm hex bit, secure
top with ⁄”-20x19mm joint connector bolts. DO NOT
FULLY TIGHTEN until Step 6.
3. Remove the #12 star lock washers and M6-1x10mm
screws located in the legs .
Align holes in cross bar  with pilot holes in legs .
Attach using #12 star lock washers and M6-1x10mm
screws. The bar should rest inside the legs. DO NOT
FULLY TIGHTEN until Step 6.
If you have an adjustable cross bar, use #12 star lock
washers and M6-1x14mm screws to fasten the two
connector bars together. DO NOT FULLY TIGHTEN
until Step 6.
4. If assembling a desk or table with a foot rest bar,
repeat Step 3 with the foot rest bar on the lower
portion of the legs.
5. If assembling a table/workstation with metal wire
management, align pre-drilled holes in metal wire
management with pilot holes in the top.
Attach wire management to top using #8x⁄” screws
and a Phillips screwdriver. Fasten down tightly.
6. Fully tighten legs , connector bar  & foot rest
(if foot rest was ordered) with fasteners. Adjust leg
height and glides as needed.
7. If assembling a table/workstation with grommet(s),
insert grommet(s) into the pre-determined location in
the top.
8. If optional footing was ordered, remove nylon glide
 from leg by rotating it counterclockwise until glide
is free.
Place stem of optional footing into the hole on the
leg. Rotate clockwise until fully inserted into leg.
Tighten with a 14mm open-ended wrench (for dual
wheel caster only).
Repeat for each caster/glide.






4
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
ASSEMBLY



12. If a backpack hook was ordere, determine the
location in which you would like to place the optional
backpack hook . Remove the joint connector bolt
from the leg plate  in the determined location.
Align tab of the backpack hook on top of the leg
plate.
Using a 4mm Allen wrench or 4mm hex bit,
secure backpack hook to the leg plate  with a
⁄”-20x19mm joint connector bolt.
