WB Manufacturing Rhapsody M4201 User manual

507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303wibenchmfg.com 1
V021518 subject to change.
Rhapsody® Cabinet/M4201
Assembly Instructions
Step 1:
Start assembly with side panel(A) on a
protected oor with dowel holes facing up.
(The back edge has dowel holes aligned from
top to bottom.)
Step 2:
Align the dowels of subtop panel(B) with
the holes on side panel(A). (TFL edge of
subtop panel(B) will need to face to the front
of the cabinet and you will need to apply an
adhesive PVA white glue* to the dowels.)
Step 3:
Align the dowels of the Lotz Armor Edge™
shelf(C) with the holes on side panel(A).
(Radius front edge of the shelf will need to
face to the front of the cabinet and you will
need to apply an adhesive PVA white glue*
to the dowels.) You will need to repeat this
for the remaining shelves on the right hand
side.
Step 4:
Align the dowels of bottom panel w/
Lotz Armor Edge™(D) with the holes on
side panel(A). (Make sure the holes for the
levelers are facing the outside edge of the
cabinet and you need to apply an adhesive
PVA white glue* to the dowels.)
Before you begin, please make sure all parts and proper quantities are included. Any parts damaged during shipment must be
reported within 5 days of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.
Part Description
ASide Panel (right side)(lay this panel on the oor)
BSubtop Panel
CShelves w/Lotz Armor Edge™
DBottom Panel w/Lotz Armor Edge™
EMiddle Panel
FBack Panel
GToe Kick
HSide Panel (left side) A
B
D
G
E
C
F
H
Step 5:
Align the dowel holes of the middle panel(E)
with the dowels on each of the shelves (You
need to apply an adhesive PVA white glue* to
the dowels on the shelves.)
Step 6:
You will now need to repeat Steps 2-4 to
assemble the left side of cabinet (Don’t forget to
always apply an adhesive PVA white glue* to
the dowels.)
Step 7:
Align the dowels of back panel(F) with the
holes on side panel(A). (You will need apply an
adhesive PVA white glue* to the dowels.)
*Adhesive PVA white glue and clamps are not provided.
ont
a
n
.
)
C & D
Countertop

507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303wibenchmfg.com 2
Rhapsody® Cabinet/M4201
Assembly Instructions-Cont.
Before you begin, please make sure all parts and proper quantities are included. Any parts damaged during shipment must be
reported within 5 days of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.
I
G
J
Built-in leveler
A
B
K
D
E
C
H
F
Part Description
ASide Panel (right side)(lay this panel on the oor)
BSubtop Panel
CShelves w/Lotz Armor Edge™
DBottom Panel w/Lotz Armor Edge™
EMiddle Panel
FBack Panel
GToe Kick
HSide Panel (left side)
IToe Rail
JLevelers (set of 4)
KCountertop
LMusic Cabinet Grille Doors (left hand)
M & N Black Magnet Catch(M) on Door Latch(N)
Step 8:
Align the dowels of toe kick(G) with holes on
side panels(A). (You will need apply an adhesive
PVA white glue* to the dowels.)
Step 9:
Align the dowel holes of side panel(H) with the
dowels on panels(B, D, F & G). (You will need
apply an adhesive PVA white glue* to the
dowels on panels B, D, F & G.) (B & D panels will
be the left hand side of those panels.)
Step 10:
Install toe rail(I) using 1 ½” face frame screws
Step 11:
Install the levelers(J) using #6x ½” zinc Phillips
screws in each corner of bottom panel(D).
Step 12:
Stand cabinet upright (ask for help).
L
*Adhesive PVA white glue and clamps are not provided.
Countertop
N
M
Step 13:
Install countertop(K) over subtop panel(B) using
¼-20x30mm black joint connector bolts.
Step 14:
Align grille doors(L) (left hand) with pre-drilled
holes using black #8x ⁄” at head wood screws.
Step 15:
Align screw holes on black magnet catch(M)
and door latch(N) and then use 2, 6x ¾” black
pan screws to attach magnet catch(M) and door
latch(N) to the inside of side panel(A). Use 1 #8x
⁄” at head wood screw to further secure door
latch(N) to inside of side panel(A).
Step 16:
WB Mfg. would recommend applying clamps*
(not provided) down the sides of panels E & A
and A & H.