WB Manufacturing LOBO User manual

1
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
Step 1:
• If assembling a Hardwood top that has a depth greater than 36”,
top will be in 2 pieces (.5”undersized on length). Place both top
halves face down on a protected at surface. Align together the
dog bone holes on both tops.
Step 2:
• Adjust Tite joint fastener to the size of the eld joint opening
and then place the fastener into each opening. Using a ⁄”
wrench, tighten each fastener so that both tops are securely
clamped together.
Step 3:
• Place LOBO frame tabs down on top of the LOBO top and align
with pre-drilled pilot holes.
Step 4:
• Starting at one corner, place the ⁄” bolt that is welded to leg
through corner support brace of frame.
Step 5:
• Using a # S2 square bit, secure the leg plate to the tabletop with
#10 x ¾” square pan screws. Repeat for each leg plate.
Step 6:
• Place the ⁄”lock washer and ⁄” hex nut onto the leg bolt and
tighten with ½”wrench. Repeat Steps 4 & 5 on remaining legs.
Step 7:
• Using a # S2 square bit, secure frame to table top with #10 x ¾”
Square pan screws. One screw per tab.
Step 8:
• With someone’s help, turn table upright.
Step 6
Step 7
Tools Required
• ½”Wrench
• ⁄”Wrench
• Screw gun
• # S2 Square bit
Shown with optional gussets
Step 4
Step 2
Step 5
Shown with
optional gussets
LOBO Tables
2 Piece Butcherblock Top
Assembly Instructions
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key) Any parts damaged during shipment must be reported
within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.

2
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
3” Heavy Duty Caster Hardware Pack (04066968) Used only with 2”adj. legs (-ALR & -ABP)
Part # Description Qty.
04067460
04067064
¼” Star washers
M6 1x18 screws
(Used in leg insert to prevent bending of the leg insert)
4 per set
4 per set
(Included in Hardware Pack located in leg box as
standard. Discard if casters are not installed.)
3” Heavy Duty Caster Hardware Pack (0402020) Used only with 1.5”adj. legs (-ADJ)
04067460
0401259
¼” Star washers
M6 1x14 screws
(Used in leg insert to prevent bending of the leg insert)
4 per set
4 per set
(Included in Hardware Pack located in leg box as
standard. Discard if casters are not installed.)
LOB -ADJ
LOB -ABP
LOB -ALR
LOB -FX
Adjustable Legs
Fixed Legs
Model #
Smooth Silver
Sku #
Black
Sku# Descripon Weight Height"
LOB -ADJ 0409195-G4 0409195 LOBO 1.5" (40mm) Square Adj. Leg 18 22 - 36.6
LOB -ALR 0409193-G4 0409193 LOBO 2" (50mm) Round Adj. Leg 20 22.25 - 36.25
LOB -ABP N/A 0409196 LOBO 2" (50mm) Big Paw Sq. Adj. Leg 20 22.25 - 36.25
Model #
Smooth Silver
Sku #
Black
Sku# Descripon Weight Height"
LOB -FX 0409194-G4 0409194 LOBO 1.5" (40mm) Square Fixed Leg 16 28.5
LOBO Legs
Part # Description Qty.
0406902 Tite joint fasteners # depends on top size
0408231 #10 x ¾” Square pan screws
(Used to attach leg plates and frame to top)
26
(Included in Hardware Pack located in leg box. May
need less depending on size and work service)
Hardware Pack
040379
⁄” Lock washers
⁄” Hex nuts
(Used to attach legs to frame)
4
4
Part Identifier Key
LOBO Tables
2 Piece Butcherblock Top

3
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
LOBO Tables
w/ Gussets
Step 1:
• Make sure that legs are fully installed and adjusted to the correct
height.
Step 2:
• Place gusset in corner where leg and frame meet. Use a rubber
mallet to tap the #10 self-drilling screws into place.
Step 3:
• Using a screw gun along with a ⁄”hex bit to nish fastening the
gussets to the leg and frame with the #10 self-drilling screws.
Step 4:
• Repeat for remaining gussets.
Gussets w/ Hardware Pack (04066920) Used only with square LOBO legs
Part # Description Qty.
04009742 #10 Self-drilling screws 8 per gusset
04066920 Gusset for square legs 1 per leg
Gussets w/ Hardware Pack (04066918) Used only with round LOBO legs
Part # Description Qty.
04009742 #10 Self-drilling screws 8 per gusset
04066918 Gusset for square legs 1 per leg
Part Identifier Key
Tools Required
• Screw Gun
• ⁄” Hex Bit
• Rubber Mallet
Assembly Instructions
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key) Any parts damaged during shipment must be reported
within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.
Gussets are NOT available on shaped tables excluding the Round ones.

4
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
LOBO Tables
w/ Casters, Glides & Leg Info.
Step 1:
• Remove Nylon glide from leg by rotating counterclockwise until glide is free.
Step 2:
• Place stem of optional footing into the hole on the leg. Rotate clockwise
until fully inserted into leg.
• Casters are NOT to be used as a leveling device.
Step 3:
• Tighten with a 14mm open-ended wrench. (only with the Dual wheel soft
tread locking caster.)
Step 4:
• Repeat for each caster or glide.
Assembly Instructions
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key) Any parts damaged during shipment must be reported
within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.
Part # Description Qty.
040164 1⁄ Dia. Grand Hank glide, ⁄-16 x 1” 1 per leg
04067920 1.5” Soft Touch glide 1 per leg
33056S 1.25” Steel glide 1 per leg
04067540 Dual wheel soft tread locking casters
(N/A on epoxy resin tops) 1 per leg
LOB -ADJ
LOB -ABP
LOB -ALR
LOB -FX
Adjustable Legs
Fixed Legs
Model #
Smooth Silver
Sku #
Black
Sku# Descripon Weight Height"
LOB -ADJ 0409195-G4 0409195 LOBO 1.5" (40mm) Square Adj. Leg 18 22 - 36.6
LOB -ALR 0409193-G4 0409193 LOBO 2" (50mm) Round Adj. Leg 20 22.25 - 36.25
LOB -ABP N/A 0409196 LOBO 2" (50mm) Big Paw Sq. Adj. Leg 20 22.25 - 36.25
Model #
Smooth Silver
Sku #
Black
Sku# Descripon Weight Height"
LOB -FX 0409194-G4 0409194 LOBO 1.5" (40mm) Square Fixed Leg 16 28.5
LOBO Legs
Part Identifier Key
Installing casters on tables with epoxy resin tops will void the Epoxy warranty.
Tools Required
• 14mm open-ended wrench