WB Manufacturing TD6071-95UNET-AC User manual

1
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
800-242-2303
wibenchmfg.com
UNIVERSAL APPLETON/
APPLETON TEACHER’S DESK
PARTS
PARTS x QTY
# DESCRIPTION x QTY
1 Laminate Top x 1
2 Base Cabinet x 1
3 Leg x 1 or 2 Depending On Model
4 Dual Wheel Casters x 2
5 Dual Wheel Casters x 4
6 Laminate Modesty Panel x 1 (Optional)
7 Perforated Metal Modesty Panel x 1 (Optional)
HARDWARE x QTY
Dual wheel non-locking
plate casters x 2
04009656
⁄” - 20x25mm JCB x 16
04066947
27x27x50 L-brackets x 4
0406829
#10x⁄” pan head Phillips screws
x 16
0401036
NOTE: Before you begin, please make sure
all parts and proper quantities are included.
Any parts damaged during shipment must be
reported within 24 hours of receipt. To report
information regarding damages or if you have
any questions, please call 800.242.2303.
V051222 Version subject to change







TOOLS NEEDED
Drill 4mm Allen
Wrench
4mm Hex
Bit
Phillips
Screwdriver
Phillips
Drill Bit
Assistance14mm Open
Ended Wrench
Dual wheel locking
plate casters x 2
04009658
⁄” - 20x35mm JCB x 4
0406686-WO
Dual wheel non-locking
stem casters x Varies
04067540
⁄” - 20x15mm JCB x 5
(For optional perforated metal
modesty panel)
UNET -EJA ELS - EJA
UNET Leg (SS) x 1
04067355-G4
UNET Leg (Black) x 1
04067355
ELO® Legs (SS) x 2
04066652-G4
ELO® Legs (black) x 2
04066652
⁄” - 20x15mm JCB x 6 (UNE-T
leg) x 12 (ELO® leg)
04009023
NOTE: These instructions are based on model #TD6071-95UNET-AC. These instructions work for all
Universal Appleton & Appleton Teacher’s Desk models. Product images are for illustrative purposes only
and may differ from actual product.

2
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
ASSEMBLY
1. Place the top  face down on a protected flat
surface so threaded inserts are facing up.
2. With drawers taken out of base cabinet (if unit has
them), place base cabinet  upside down on the
top, aligning pre-drilled holes in base cabinet with
threaded inserts in top.
Using a 4mm Allen wrench or 4mm hex bit, fasten
base cabinet to top with ⁄”-20x35mm joint
connector bolts.
4. If casters  &  are needed, remove glides from
leg(s) by rotating counter clockwise. If glides will
be used, skips Steps 4 & 5. Insert dual wheel
locking casters into leg(s) . Tighten with a 14mm
open-ended wrench.
3. Align pre-drilled holes in leg(s)  with threaded
inserts in top , making sure the long side of leg
plate(s) is facing the same direction as the front side
of base cabinet.
Using a 4mm Allen wrench or 4mm hex bit and screw
gun, fasten leg(s) to top with ⁄”-20x15mm joint
connector bolts. These bolts will be used for either
(ELS or UNET) leg(s).
5. Place (2) locking and (2) non-locking 75mm plate
casters  on the caster base of the base cabinet
, aligning the holes in the plates with the threaded
inserts in the caster base. We recommend placing
the two locking casters towards the front end of the
cabinet. Using a 4mm Allen wrench or 4mm hex bit,
fasten casters to the caster base with ⁄”-20x25mm
joint connector bolts.
The assembly of this desk requires the
assistance of another person.
NOTE: Hardware packs are included in
packaging. You may receive more hardware
than needed. Discard any extra hardware after
assembly.

3
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
8. Place drawers back in unit. Flip wire pulls to front.
7. With assistance, turn desk upright.6a. (Only if optional STEEL PERFORATED modesty
panel was ordered.) Align the perforated modesty
panel  with the five staggered threaded inserts
in the top . The modesty panel will be located
towards the back side of the base cabinet. Using a
4mm Allen wrench or 4mm hex bit and screw gun,
fasten modesty panel to top with ⁄”-20x15mm joint
connector bolts.
6b. (Only if optional LAMINATE modesty panel was
ordered.) Align the laminate modesty panel  with
the two most inner staggered threaded inserts
in the top . The modesty panel will be located
towards the back side of the base cabinet . Attach
L-brackets with pan head Phillips screws to secure
modesty panel in place. Using (1) L-bracket, attach
the end of the modesty panel. Use (2) L-brackets to
attach long side of panel to top. (See image for the
approximate location.) Use final L-bracket to attach
panel on opposite side to the top.
ASSEMBLY
NOTE: Keys for drawer locks will be taped to
the inside of the drawers.