WE-EF FLA440 Series User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Area Floodlight
FLA440 LED
FLA460 LED
Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.

1
Area Floodlight
145
260
385
495
ø 14
ø 14
ø 18 44
205
360
530
685
ø 14
ø 14
ø 18 44
FLA440 FLA460
F/A4436:I366, Class I, ta ů4C
F/A444:I366, Class I, ta ů2C
F/A462:I366, Class I, ta ů2C
F/A461: I 366, Class I, ta ů2C

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
by a suitably qualiƂed and trained professional.
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a
suitably qualiƂed professional in compliance with latest
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice: If the luminaire is modiƂed by anybody other
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
Attention: The housing Hcontaining the LED light
source is factory-sealed and does not need to be
opened during installation.
Installation Procedure
1) Prior to electrical connection, proceed with
mechanical installation by securing stirrup Ato
optional mounting accessory or directly to a suit-
able surface. Aim luminaire in the desired direction.
Warning: Ensure not to damage any electric cable,
water pipe or other devices while drilling holes.
2) Switch off mains electrical supply.
3) Remove gear box cover Bby loosening screws C.
4) Check that rating shown on luminaire label conforms
with mains electrical supply.
5) Feed mains supply cable Kthrough cable gland G
(Fig. I).
6) Connect mains supply cable K leads, and control
lines where applicable, to respective terminals in
terminal connector F:
a) ON/OFF or WE-EF Control Advanced (L = Phase,
N = Neutral, = Earthing)
b) WE-EF Control Basic (L = Phase, N = Neutral,
= Earthing, Ls = Switching Phase)
c) 1-10 V/DALI or WE-EF Control Dynamic (L = Phase,
N = Neutral, = Earthing, DA/DA = DALI control
line, D-/D+ = 1-10 V
control line).
7) Tighten cable gland G.
8) Reposition gear box cover Band retighten screws C.
9) To aim luminaire: Loosen screws Jslightly, adjust
aiming then retighten screws J. Tighten screw Ito
secure orientation of luminaire.

4
Fig. I. Feed mains supply cable through cable gland

5
Mounting Accessories
Pole bracket D
KA1 for 1 x FLA440/460 310-9126 ø 76 x 100
KA2 for 2 x FLA440/460 310-9127 ø 76 x 100
Mounting Ƃtter D
TA1 for 1 x FLA440/460 310-9124 ø 76 x 100
TA2 for 2 x FLA440/460 310-9125 ø 76 x 100
Pipe clamp D
SP1 for 1 x FLA440/460 146-0241 ø 38-60
SP1 for 1 x FLA440/460 146-0242 ø 76-89
SP2 for 2 x FLA440/460 146-0243 ø 38-60
SP2 for 2 x FLA440/460 146-0244 ø 76-89
D
TA1/TA2
D
KA1/KA2
SP1/SP2

6
Pole clamp D
TS1 for 1 x FLA440 147-0543 ø 76-89
TS1 for 1 x FLA440 147-0544 ø 114-133
TS2 for 2 x FLA440 147-0545 ø 76-89
TS2 for 2 x FLA440 147-0546 ø 114-133
TS1 for 1 x FLA460 147-0547 ø 76-89
TS1 for 1 x FLA460 147-0548 ø 114-133
TS2 for 2 x FLA460 147-0549 ø 76-89
TS2 for 2 x FLA460 147-0550 ø 114-133
Junction box
JB1 for FLA440/460 310-9001
Short post – Matching planted root to be ordered separately.
EM1 for FLA440/460 270-9038
Planted root – Galvanised steel.
ESV4 for short post 300-0461
JB1
TS1/TS2
D
EM1
ESV4

www.we-ef.com
TO9228W0617 © WE-EF 2017
Technical speciƂcations are
subject to change.
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
info.asiapaciƂ[e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]