WE-EF ETC320-GBLED User manual

WE-EFLEUCHTEN
Installation and Maintenance
Instructions
Inground Luminaire
ETC320-GBLED
Surge Protection
This product has a built in level of surge protection. For comprehensive
protection of a luminaire installation against lightning and electrical surges,
it is essential to cover mains supply and data input lines at the distribution
board level, by using respective primary (Type 1) and secondary (Type 2)
surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation. Also, disconnect luminaires before
operating high-power devices such as, for example, electrical arcwelders.
INSTALLER
HOTLINE
[phone]
7am–7pm AEST
Do not handle the luminaire by holding
the cable end!
Refer to the instructions contained in this
document for details.

Inground Luminaire
IP67, Class I, ta =25°C
Y
1
X
W
Fig. I

Light Source
LED
Maintenance
Warning: Do not open luminaire while mains supply is switched on.
1) Switch off mains electrical supply.
2) Remove cover and lens/gasket assembly. Clean all surfaces and ensure that threaded entries are free from
dirt by using a wet cloth with mild detergent.
3) Check gasket for damage and replace if necessary.
Attention: In case of damage to the lens, the complete lens/gasket assembly must be replaced.
4) In case of damage to the LED, the complete gimbal module X must be returned to WE-EF for factory-
maintenance (contact your authorised WE-EF agent for service). To remove the gimbal module proceed as
follows (Fig. I):
a)Rotate wheel W (using a standard tool) in the direction of the 'open' mark until the gimbal module can be
pulled out of the luminaire housing.
b) Detach terminal connector Y and remove gimbal module X.
c) Properly package gimbal module X and return to WE-EF for factory-maintenance.
Attention: During the factory-maintenance period, ensure both the luminaire cover and lens are secured in
position.
5) To install gimbal module X, attach terminal connector Y. Set gimbal module X into luminaire housing. Rotate
wheel W in the direction of the 'lock' mark until gimbal module X is firmly secure. Follow steps 11-16 to
close the luminaire (see: Phase Two –Luminaire Installation, Electrical Connection, and Aiming Procedure).
Do not handle the luminaire by holding the cable end! Doing so can damage the supply cable.
Damaged mains supply cable: Contact your authorised WE-EF agent for replacement.
2

Installation
The product must be installed and maintained by a
suitably qualified professional in compliance with latest
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply priorto
installing and connecting the luminaire.
Notice: If the luminaire is modified by anybody other
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof,are
excluded.
Installation Methods
For proper installation, use the supplied installation
blockout.
Ensure that proper drainage is provided for the shown
installation methods:
In landscape areas, soil with gravel base (Fig. II).
In paved areas, concrete with gravel base (Fig. III).
3
Fig. II
Fig. III
`

Phase One
Blockout Installation Procedure
(during earth or masonry work)
1) Ensure a suitable recess is provided to accommo-
date installation blockout/mounting ring assembly
L/H.
2) Set installation blockout/mounting ring assembly
L/H in position and ensure that:
a)Arrow R on mounting ring H is pointedtowards
the object to be illuminated (wall, tree, column).
b)Mounting ring H is flush with surface F. If the
floor will be tiled or paved afterwards, leave an
appropriate gap.
c)Mains supply cable(s) Ois of sufficient length to
connect sealable junction box Jwith cable Nfrom
luminaire.
3) During ongoing earth and/or masonry works, do
not remove screws M from mounting ring H.
Ensure that installation blockout/mounting ring
assembly L/H is not damaged and hasmaintained
its original shape. If necessary use a cover plate.
4

12)Insert screw driver into a slot on locking wheel W.
Rotate locking wheel W in the 'LOCK' direction
until the gimbal is firmly secured (Fig. V).
Warning: Do not tighten more than necessary to
secure gimbal.
13)Ensure that all surfaces are clean and dry.
Reposition lens/gasket assembly B, cover Aand
screws D on luminaire housing C.
14)Switch on mains electrical supply and operatelight
source for approximately 30 minutes to dry any
moisture.
Attention: Do not switch off LED before luminaire
is properly sealed.
15)Secure cover A as follow:
a)Partially secure screws D in criss-cross
sequence (Fig. VI) starting from position1.
b) Tighten screws D in same sequence.
c)Fully tighten screws D in same sequenceagain,
using torque 3 Nm.
5
Phase Two
Luminaire Installation, Electrical Connection, and
Aiming Procedure
4) Switch off mains electrical supply.
5) Check that rating shown on luminaire label con-
forms with mains electrical supply.
6) Remove screws M from mounting ring H.
7) Terminate cable N from luminaire C and mains sup-
ply cable O (for individual wiring) or branch cable
(for through wiring) in sealable junction box J –to
connect cable(s). Follow the sealable junction box
termination instruction included in the packaging.
8) Remove cover A and lens/gasket assembly Bby
loosening screws D.
9) Set cables and sealable junction box Jinside
installation blockout L.
10)Place luminaire housing C into installation block-
out/mounting ring assembly L/H. Secure luminaire
with mounting ring H by tightening screws M.
Warning: When luminaire is placed inside installa-
tion blockout L, ensure there is no stress on seal-
able junction box J or electric cables (Fig. IV).
Aiming of gimbal
11)Insert a standard tool into a slot on locking wheel
W. Rotate locking wheel W in the 'OPEN' direction
until gimbal can be moved (Fig. V).
To horizontally aim the gimbal
(Rotation 355°)
Hold fins E to rotate thegimbal.
To vertically aim the gimbal
(Tilt 0-20°)
a) Insert screw driver into hole T.
b)Adjust gimbal to desired angle (Refer to protrac-
tor scale U).
Note: Angle can be adjusted in 2°increments.

R
MJ
O
N
O
D
A
B
C
HF
L
6

Fig. V
GT
W
E
U
Fig. IV
J
HM
C
N
L
F
7

NOTE: LED luminaires are static sensitive devices; please ensure that appropriate ESD measures
are taken before opening luminaire. If in doubt, please contact WE-EF.
The desiccant sachet MUST not be left in the open environment. please seal
luminaire down within 15 minutes of opening sachet.
2. Loosen and remove heatsink
assembly
3. Open Desiccant sachet.
1. Open cover and install as per
installation instructions
4. Place Desiccant sachet into housing
and replace heatsink assembly
8

Installation Instruction
Inserting Desiccant sachet into ETC gimbal
5. Aim gimbal and tighten 6. Place lens back onto housing
noting alignment of indexing
stud
7. Tighten cover down to
recommended torque in criss-cross
pattern as per instructions. 9

TO9191W0218 © WE-EF 2020
Technical specifications are
subject to change.
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
INSTALLER
HOTLINE
[phone]
7am–7pm AEST