Weider 2100 User manual

MEIDER2100
Model No. 831.159010
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
_" X F-. R C I SE.
EQUIPMENT
HELPLINE!
!-800-736-6879
SEARS, ROEBUCK AND CO.
HOFFMAN ESTATES, IL 60179
USER'S MANUAL
www.weiderfit ness.com
new products, prizes,
fitness tips, and much more!

TABLE OF CONTENTS
IMPORTANT PRECAUTIONS ............................................................. 3
BEFORE YOU BEGIN ................................................................... 4
ASSEMBLY ........................................................................... 5
ADJUSTMENTS ...................................................................... 14
WEIGHT RESISTANCE CHART ........................................................... 16
CABLE DIAGRAM ..................................................................... 17
EXERCISE GUIDELINES ................................................................ 18
ORDERING REPLACEMENT PARTS ................................................ Back Cover
LIMITED WARRANTY ........................................................... BackCover
Note:A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of
this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before
beginningassembly.
WELDER is a registeredtrademark of ICON Health & Fitness, Inc.
2

IMPORTANT PRECAUTIONS
WARNING: To reduce the rlsk of serious injury, reed the following Important precau-
tions before using the weight system.
1, Read all Instructions in this manual and In
the accompanying literature before using the
weight system. Use the weight system only
as described in this manual.
11. Make sure that the cables remain on the pul-
leys at all times. If the cables bind while you
are exercising, stop Immediately and make
sure that the cables are on all of the pulleys.
2. It Is the responsibility of the owner to ensure 12. Always stand on thefoot plate when per-
that an users of the weight system are ade- formlng an exercise that could cause the
quately Informed of all precautions, weight system to tip.
3. The weight system Is Intended forhome use 13. Always disconnect the lat bar from the
Ing down.
7. Keep hands and feet eway;frommovlngparts:
9,
our toll-free HELPLINE
Uon shown.
• Misuseofthisproduct
mayresultinserious
injury.
•Readuser'smanual
andfollowall warnings
andooeratinginstruc
tionsenortouse
•Donotallowchilaren
onorarounomacn_ne
•Replacelabelif
damaged,illegible,or
removeo.
Decal I
10. Never release the press arm, butterftyfarms,
leg lever, at bar, ()r handle whllewelgh;ts_are
raised, the weights will fall with great force. Decal 2
3

BEFORE YOU BEGIN
Thank you for selectingthe versatile WELDER®2100
weight system.The WELDER" 2100 offersaselection
of weightstationsdesigned todevelop every major
musclegroup ofthe body.Whether yourgoal isto tone
your body,builddramatic muscle size and strength,or
improveyourcardiovascularsystem,the WELDER®
2100 will helpyou to achieve the resultsyou want.
For your benefit, read this manual carefully before
using the weight system, ifyou have additional
questions,please call ourtoll-free HELPLINE at
1-800-736-6879, Monday throughSaturday,7a.m.
until7 p.m. Central Time (excludingholidays).To help
usassistyou, please note the productmodelnumber
and serial number beforecalling.The model numberis
831.159010. The serial numbercan befound on a
decal attached to the weightsystem (see the front
coverof this manual).
Before readingfurther,please review the drawing
belowand familiarizeyourselfwith the parts that are
labeled.
LSt Bar
High PulleyStation
PressArm/Butterfly
Front Upright
ASSEMBLED
DIMENSIONS:
Height: 74 in.
Width: 42 in.
Length: 60 in.
Warning Decal 2
(One on each side
of the front upright.)
Decal 1
Backrest
Seat Weight Carriage
Leg Lever Low Pulley Station
Foot Plate
4

ASSEMBLY
• As you assemble theweight system,make sure
all parts are orientedas shownin the drawings.
Before beginning assembly, carefully rend the
following Information and Instructions:
•Assemblyrequirestwo people.
•Place all parts in a cleared area and remove the
packing materials. Do not disposeof the packing
materials untilassembly iscompleted.
•"13ghtenall partsas you assemble them, unless
instructedto do otherwise.
•For help identifyingsmall parts, use the PART
The following tools (not Included) are required
for assembly:
•two adjustable wrenches
•one rubber mallet
•one standard screwdriver
• one Phillips screwdriver
•lubricant, such as grease or petroleum jelly,
and soapy water.
Assemblywillbe moreconvenientifyou have a
socketset, a set of open-endor closed-end
wrenches, or a set of ratchetwrenches.
1.
2.
Before beginning assembly, be sure that you
have rend and understand the Information In
the box above.
Presstwo 50mm x 75mm Inner Caps (29) into
the sides ofthe Foot Plate (74).
Orientthe Rear Base (3) with the indents around
the holeson the bottom.Attach the Front Base
(1) and the Rear Base tothe Center Base (2) with
two M10 x 70mm Bolts(58) and two M10 Nylon
Locknuts(71).
Insertsix M10 x 65mm Carriage Bolts(57) up
throughthe Frontand Rear Bases (1, 3).
Press the three Base Caps (28) onto the ends of
the Front Base (1), the Center Base (2), and the
Rear Base. Secure the Base Caps withthree M4
x 20mm Screws(77) and three M5 Washers (75).
Attachthe Foot Plate (74) to the Center Base (2)
withtwo M10 x 65mm Carriage Bolts(57) and
two M10 Nylon Locknuts(71).
2
28
75
3
71
2
58 Indents
1
58 29 74
77
1
2
71
_75
77
-71
57 57
5

3. Attach the Rear Upright (7) to the Rear Base (3)
with the two indicatedM10 x 65mm Carriage
Bolts(57) and two M10 Nylon Locknuts(71).
Press a 38mm Square InnerCap (41) intothe
tube on the Front Upright (6).
Attachthe Front Upright (6) to the FrontBase (1)
with thetwo indicatedM10 x 65mm Carriage
Bolts(57) and two M10 Nylon Locknuts(71).
Do not tighten the MIO Nylon Locknuts (71)
yet.
4. Press a50mm Square Inner Cap (22) intothe
Seat Upright (73). Attachthe Bumper (25) to the
Seat Uprightwith an M4 x 20mm Screw (77) and
an M5 Washer (75).
Attachthe Seat Upright(73) to the Front Base (1)
with the two indicatedM10 x 65mm Carriage
Bolts(57) and two M10 Nylon Locknuts(71). Do
not tighten the Nylon Locknute yet.
5. Make sure there is a Carriage Bushing(32) inside
the top of the Carriage Stop (31). Slide the
Carriage Stop onto the Rear Upright(7) and
attach itat the indicatedhole (see the insetdraw-
ing) withan M8 x 70mm Bolt(72) and an M8
Nylon Locknut (70).
Make sure there are two Carriage Bushing(32)
inside thetop and bottomof the Weight Carriage
(14). Presstwo 25mm Round Inner Caps (33)
intothe ends of the tube on the Weight Carriage.
Insertan M10 x 20mm Bolt(67) intothe bracket
on the Weight Carriage.
Slide the Weight Carriage (14) ontothe Rear
Upright (7). Press a 50mm Square Inner Cap (22)
ontothe top of the Rear Upright.
4
77
5
6
71
157
22
75
57

6. Pressa 50mm Square Inner Cap (22) intothe
end of the Top Frame (8).
Attachthe Top Frame (8) to the Front Upright(6)
withtwo M10 x 70mm Bolts(58), the 90mm
Space SupportPlate (21), and two M10 Nylon
Locknuts(71).
Attach the Top Frame (8) tothe Rear Upright(7)
with two M1Ox 70mm Bolts(58), the 70mm
Space Support Plate (56), and an M10 Nylon
Locknut(71).
0o not tighten the M10 Nylon Looknuts (71)
yet.
7. Attachthe Seat Frame (5) to the Front Upright(6)
withtwo M10 x 70ram Bolts(58), two M10
Washers (26), and two M10 Nylon Locknuts(71).
Attach the Seat Frame (5) to the Seat Upright
(73) with two M10 x 70ram Bolts (58), two M10
Washers (26), and two M10 Nylon Locknuts(71).
Tighten the M10 Nylon Locknuts (71) used In
steps 2-7.
8. Press a 50mm Square Inner Cap (22) intothe
ButterflyFrame (9).
Lubricatethe M10 x 75mm Bolt(60) with grease.
Attach the ButterflyFrame (9) to the Top Frame
(8) withthe Boltand an M10 Nylon Locknut(71).
Do not overtlghten the Locknut; the Butterlly
Frame must be able to pivot easily.
658
•0"i
22 ..-'_
6O
7

9. 9
Press a 40mm x 50mm Inner Cap (23) intothe
indicatedend of the RightButterflyArm (11). Wet
the bottomend of theArm with soapy water. Slide
a Large Foam Pad (19) ontothe Arm.
Attach a Pivot Bracket (48) to the Right Butterfly
Arm (11) with an M10 x 50mm Bolt(62) and an
M10 Nylon Locknut(71). Do not overtlghten the
Looknut; the Pivot Bracket must be able to
pivot easily.
Slide aFoam Grip (76) ontothe Right Handle
(13). Attachthe Handle to the Right ButterflyArm
(11) withtwo M8 x 15ram Bolts(64).
Slide the Large Foam Pad (19) down sothat the
bottomof the Foam Pad iseven with the bottomof
the Arm.
Repeat this step with the Left Butterfly Arm (10).
10. Lubricatean M10 x 82mm Bolt(50) and both
sides of two PlasticWashers (55) with grease.
Attach the Right ButterflyArm (11) tothe Butterfly
Frame (9) withthe Bolt, the two PlasticWashers,
two ButterflyCaps (54), and an M10 Nylon
Locknut(71). Do not overtlghten the Locknut;
the Butterfly Arm must be able to pivot easily,
Be sure the indented sides of the Plastic
Washers fit over the welded bushing In the
Butterfly Arm.
Repeat this step with the Left Butterfly Arm
(10).
11. Press two 40mm x 50mm Inner Caps (23) into
the ends of the Leg Lever (4).
Lubricatean M10 x 65mm Bolt (59) with grease.
Attach the Leg Lever (4) to the Seat Upright(73)
with the Boltand an M1ONylon Locknut(71). Do
not overt_ghten the Locknut; the Leg Lever
must be able to pivot easily.
11
10
11
11
Welded Lubricate
Bushir x'_50
'l
55_ """-
9"" i
Lubricate
71
73
23
4_Lubricate
23--
8

12. Locate the Butterfly Cable (46). Attach the
ButterflyCable to the indicatedPivotBracket (48)
with an M8 x 27mm Shoulder Bolt(63) and an M8
Nylon Locknut (70).
13. Wrap the ButterflyCable (46) arounda "V"-Pulley
(39). Attach the Pulley and a Long Cable Trap
(40) tothe bracket on the Front Upright(6) with
an M10 x 55mm Bolt (69) and an M10 Nylon
Locknut(71). Be sure the Cable Trap Is turned
to hold the Cable In the Groove of the Pulley.
14, Wrap the ButterflyCable (46) arounda 90mm
Pulley(38). Attach the Pulleytothe Double"U"-
Bracket (37) with an M10 x 47mm Bolt (61) and
an M10 Nylon Locknut(71).
15. Wrap the ButterflyCable (46) arounda "V"-Pulley
(39). Attach the Pulleyand a Long Cable Trap
(40) to the bracket on the Front Upright(6) with
an M10 x 55mm Bolt(69) and an M10 Nylon
Locknut(71). Be sure the Cable Trap Is turned
to hold the Cable In the Groove of the Pulley.
13
,,6
/71 39
4_/_/69
46
15
46
9

16. Attach the ButterflyCable (46) to the indicated
Pivot Bracket (48) with an M8 x 27mm Shoulder
Bolt (63) and an M8 Nylon Locknut (70).
17. Locate the High Cable (45). Routethe eyelet
end of the Cable up throughthe Top Frame (8)
and arounda 90mm Pulley(38). Attach the Pulley
inside the Top Frame with an M1Ox 7Omm Bolt
(58), two M10 Washers (26), two 13mm Spacers
(34), and an M1O Nylon Locknut(71).
18. Wrap the High Cable (45) around a 90mm Pulley
(38). Attachthe Pulley insidethe Top Frame (8)
withan M10 x 70mm Bolt (58), two M1OWashers
(26), two 13mm Spacers (34), and an M1ONylon
Locknut (71).
19. Wrap the High Cable (45) arounda 90mm Pulley
(38). Attach the Pulleyand aCable Trap (44) to
the second set of holesfrom the top ofthe two
PulleyPlates (36) with an M10 x 47mm Bolt(61)
and an M10 Nylon Locknut(71). Be sure the
Cable Trap Is turned to hold the Cable In the
Groove of the Pulley.
16
17
71 34
18
19
7O
8
6.,61
36 _
10