Weider Platinum Xp 800 User manual

ModelNo.831.153972
SerialNo.
WritetheseriaUnumberinthe
spaceaboveforfuturereference,
SeriaUNumberDecaU(underseat)
•Assembly
•Adjustments
•ConsoleOperation
• PartListandDrawing
Readallprecautionsandinstruc-
tionsin thismanualbefore
usingthisequipment. Save this
manual for future reference.
RESISTANCE SYSTEM EXERCISER
User's Manual
Sears, Roebuck and Co., Hoffman Estates, IL 80179

TABLE OF CONTENTS
WARNING DECAL PLACEMENT ............................................................. 3
HMPORTANT PRECAUTHONS ................................................................ 4
BEFORE YOU BEGIN ...................................................................... 5
ASSEMBLY ............................................................................... 6
UPPER CABLE ADJUSTMENT .............................................................. 12
ADJUSTMENTS .......................................................................... 13
CONSOLE OPERATION .................................................................... 16
CABLE DHAGRAM ......................................................................... 18
TROUBLESHOOTHNG ..................................................................... 19
EXERCISE GUiDELiNES .................................................................. 20
ORDERING REPLACEMENT PARTS .................................................. Back Cover
FULL TEN-YEAR WARRANTY ....................................................... Back Cover
Note: A PART iDENTiFiCATiON CHART and a PART LiST/EXPLODED DRAWING are attached in the center of
this manual, Remove the PART iDENTiFiCATiON CHART and PART LiST/EXPLODED DRAWING before begin-
ning assembly,
2

WARNING DECAL PLACEMENT
Keep hands
fingers clear of
this area.
o Misuse of this product may resu|t in serious
injury.
o Read user's manua| and fol|ow al| warnings
and operating instructions prior to use.
-Do not allow children on or around machine.
• Rep|aee label if damaged, illegib|e, or removed.
3

iMPORTANT PRECAUTIONS
AWARNING: Toreducethedekofeedouenjury,read fo,owingimportantprecautione
before using the resistance system.
1. Read all instructions in this manual before on the High cables only while sitting on the
using the resistance system. Use the resist- bench, with the seat in one of the three poei-
ance system only as described in this manual, tions closest to the upright base, or while
standing on the base plate.
2. mtis the responsibility of the owner to ensure
that aH users of the resistance system are 11. The crossbar on the top frame is not
adequately informed of all precautions, designed to be used for pull-up exercises. Do
not hang on the crossbar.
3. The resistance system is intended for home
use only. Do not use the resistance system in 12. The resistance system is designed to be
any commercial, rentaJ, or institutional setting, used with the included resistance. Do not
use the resistance system with any other
Use the resistance system only on a level
surface. Cover the floor beneath the resist-
ance system to protect the floor.
5. Make sure that all parts are properly tight-
ened each time the resistance system is
us ed. Replace any worn parts immediately.
6. Keep children under 12 and pets away from
the resistance system at aH times.
type of resistance.
13. Always disconnect the lat bar from the High
cables when performing an exercise that
doee not require it.
14. Make sure the storage knob is in place and
fully tightened each time the resistance sys-
tem is used.
8. AJwaye wear atHetic shoes for foot protec-
tion while exercising.
15. Make sure that the cables remain on the puJo
Keep hands and feet away from moving parts, leye at aH times, ff the cabJes bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys.
g. The resistance system is designed to sup-
port a maximum user weight of 300 pounds.
16. Do not pull on the cables while the resist-
ance level is being adjueted.
17. if you feeJ pain or dizziness while exercising,
f0. Pull on the lower cable only while sitting on stop immediately and begin cooling down.
the bench or standing on the base plate. Pull
AWAF NING: Beforebeginningthisoranyexerc eeprogram,consultyourpbye cian.THis
is especially important for persons over the age of 35 or persons with pre-existing heaJth problems.
Read aH instructions before using. Seats assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
4

BEFORE YOU Bm=GmN
Thank you for selecting the innovative WELDER®PLAT-
iNUM XP800 resistance system, The resistance system
offers a selection of stations designed to develop every
major muscle group of the body, Whether your goal is to
tone your body, build dramatic muscle size and
strength, or improve your cardiovascular system, the
resistance system will help you to achieve the specific
results you want,
For your benefit, read this manuaJ carefully before
using the resistance system, if you have questions
after reading this manual, call 1-800-4-MYoHOME ®
(1°800-469-4668), To help us assist you, please note
the product model number and serial number before
calling, The model number is 831,153972, The serial
number can be found on a decal attached to the resist°
ance system (see the front cover of this manual),
Before reading further, please review the drawing below
and familiarize yourself with the parts that are labeled,
Crossbar
Lat Bar
Console
Top Frame
High Pulley
Backrest
Storage Knob
Seat
Leg Lever
Resistance Bar
Squat Pin
Low Pulley
Row Hate
Seat Knob
Base Hate
ASSEMBLED
DiMENSiONS:
Height: 86 in,
Width: 50 in,
Depth: 85 in,
5

ASSEMBLY
Make Things Easier for Yourself
This manual is designed to ensure that the resist-
ance system can be assembled successfully by
most people. However. it is important to realize
that th6 versatile resistance system has many
parts and that the assembly process will take
time, Most people find that by setting aside plenty
of time. assembly wiii go smoothly.
Before beginning assembly, carefully read the
following information and instructions:
Assembly requires two persons,
Place all parts in a cleared area and remove the
packing materials, Do not dispose of the packing
materials until assembly is completed,
For he@ identifying small parts, use the PART
IDENTIFICATION CHART. Note: Some small
parts may have been pre-attached for shipping, if
a part is not in the parts bag, check to see if it
has been pre-attached,
• Tighten all parts as you assemble them, unless
instructed to do otherwise,
As you assemble the resistance system, make
sure all parts are oriented as shown in the draw-
ings,
H
The included Alien wrenches W _ and the foF
lowing toots (not included) are required for
assembly:
• Two adjustable wrenches
One rubber maitet
* One standard screwdriver _L_
* One Philtips screwdriver __-_D
• Lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly wiii be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches,
t, Before beginning assembJy, make sure that
you have read and understand the informa_
tion in the box above. Refe[ to the PART
iDENTiFiCATiON CHART for help !dent!fy!ng
small parts.
Pull the lower end of the Upper Wire Harness
(71) out of the hob in the back of the Upright (2),
Attach the Upright (2) to the Base Hate (1) with
an MIO x 25mm Button Screw (88), an MIO
Washer (106), an MIO x 92mm Button Bolt (83),
and an MIO Nylon Locknut (103),
71
88
6

3,
4,
insert the connector of the Upper Wire Harness
(71) into the socket of the Lower Wire Harness
(117), The connector shouJd slide easily into the
socket and snap into place, if the connector does
not slide easily and snap into place, turn the con-
nector over and then insert it,
Make sure that the connector and wires appear
as shown in the inset drawing, mFTHE CONNEC-
TOR (S NOT (NSERTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE POWER
mSTURNED ON.
insert the Mech Frame (6) into the Base Hate (1),
Attach the Mech Frame to the Upright (2) with a
1/2" x 25mm Screw (85) and a 1/2" Lock Washer
(12), Do not tighten the Screw yet.
Attach the Mech Frame (6) to the Base Hate (1)
with four M10 Nylon Locknuts (103),
Tighten the 1/2" x 25ram Screw (85}.
Press the Rail Cap (49) onto the Leg (5), Attach
the Leg to the Rail (4) with two M10 x 64mm
Button Bolts (80), four M10 Washers (106), and
two M10 Nylon Locknuts (103),
Lubricate an M10 x 125mm Button Bolt (89) with
grease, Attach the Rail (4) to the Row Hate (28)
with the Bolt, two M10 Washers (106), two 31mm
Spacers (30), and an M10 Nylon Locknut (103),
Do not overtighten the Locknut; the Rail must
be able to pivot easily.
Tighten the Storage Knob (29) into the Row Hate
(28) and the Rail (4),
\4
103 106
49
103
12
106
3O
85
80
Lubricate
Red
Wire
89
7

5. 5
6,
7,
insert the Squat Pin (66) into the Upright (2).
SHde the Squat Carriage (19) onto the Upright (2).
Attach the Top Frame (37) to the Upright (2) with
two MIO x 25mm Button Screws (88), an MIO x
75mm Button Screw (84), three MIO Lock
Washers (75), and an MIO Washer (106).
Pull the excess Upper Wire Harness (71) out of
the Upright (2). insert the connector on the
Consob (67) into the socket on the Upper Wire
Harness. The connector shoutd slide easily into
the socket and snap into place, if the connector
does not slide easily and snap into pUace,turn the
connector over and then insert it.
Make sure that the connector and wires appear
as shown in the inset drawing. IF THE CONNEC-
TOR IS NOT INSERTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE POWER
mSTURNED ON.
Push the excess Upper Wire Harness (71) into
the Upright (2).
Attach the Consob (67) to the Upright (2) with
four M4 x 70mm Screws (53).
19
66
88
75
106
53
84
Red
Wire
8

8, 8
Attach a Large Pulley (14) and the Pulley Hate
(68) to the Upright (2) with an M12 x 62mm
Button BoUt(81) and an M12 NyUonLocknut (13),
Do not tighten the Locknut yet.
9, Pull the Upper CaMe (121), which is attached
inside of the Mech Frame (not shown), up
between the Upright (2) and the Pulley Hate (68),
Attach another Large Pulley (14) to the Upright (2)
and Pulley Hate (68) with an M12 x 62mm Button
BoUt(81) and an M12 NyUonLocknut (13), Make
sure that the Upper Cable (!21} is between the
two Pulleys.
HoUdthe 38mm Spacer (90) inside the Uoopof the
Upper CaMe (121), and between the Upright (2)
and the Pulley Hate (68), Attach the Spacer with
an MIO x 58mm Button Screw (11), Make sure
the ends of the Cable do not wrap around
each other below the Spacer and the Large
Pulleys (14} used in steps 8 and 9 (refer to the
CABLE DIAGRAM on page 18}.
Tighten the M!2 Nylon Locknuts (13} used in
steps 8 and 9.
10, Attach a Small Guide Spacer (18), a Large Guide
Spacer (17), and two Crossbar Guides (15) to the
Upright (2) with an MIO x 152mm Bolt (86),
Pull the Upper Cable (121) up between the
Crossbar Guides (15), Press the metal cover on
the Cable into the groove in the Crossbar Block
(16), Attach a Small Guide Spacer (18), the
Crossbar Block, the two Crossbar Guides (15), an
MIO Thick Washer (54), and the two Tethers (70)
to the Upright (2) with another MIO x 152mm Bolt
(86), Do not tighten the Bott yet.
10
81
81
18
17
16
68
14
Metal
Cover
Groove
13
54
70
121
/-
86
9

11, insert the Resistance Bar (9) between the
Crossbar Guides (15), and center it on the
Crossbar Block (not shown),
Press a Pulley Bracket (10) onto the Resistance
Bar (9), Screw a 3/8" x 38mm Tension Screw
(114) into the Pulley Bracket a couple of turns,
Make sure the hexagonal hoJe in the Screw is
on the outside of the Bracket.
Attach a Tether (70) to the Pulley Bracket (10) at
the upper hole, with an MI0 x 64mm Button Bolt
(80), an M10 Thick Washer (54), and an MI0 Nylon
Locknut (103).
Repeat on the other side of the Resistance
Bar (9}. Then, tighten the lower M1Ox 152mm
Bolt (86} used in step 10.
12, Hold a Large Pulley (14) inside the Upper Cable
(121), Attach the Pulley to a Pulley Bracket (10)
with an M12 x 58mm Button Bolt (87) and an M12
Nylon Locknut (13), Make sure that the CabJe is
routed as shown in the CABLE DIAGRAM on
page 18.
13, Hold a Large Pulley (14) inside the Upper Cable
(121), Attach the Pulley to the other Pulley
Bracket (10) with an M12 x 58mm Button Bolt
(87) and an M12 Nylon Locknut (13), Make sure
that the Cable is routed as shown in the
CABLE DIAGRAM on page 18.
Tighten the two 3/8" x 38ram Tension Screws
(114} an equal number of turns.
14, Attach the Leg Lever (56) to the Leg (5) with a
Leg Station Pin (60), Slide a Cotter Pin (113) onto
the Leg Station Pin,
11
12
14
10
87_
7O
13
121
87
13
114
10
/
114
6O
10