Weller WAD 101 User manual

WELLER
Hot Air
Hot Air.........
.....the Solution for selective Reflow - Processes

For small Components
up to about15 X 15 mm
HAP 1
Connectable to an....
WAD 101
WMD 1A
WR 3M

WAD 101
Hot Air Station
WAD 101 Hot Air Station
The cost effective solution for
external compressed Air -, or Inert
Gas supply

WAD 101
Hot Air Unit
Consists of:
•Power supply
•Hot air pencil HAP1
•Support KH27
•Socket wrench 8mm
•2 m air hose 6mmØ

WAD 101
- Soft Ware Features
•Digital control electronic with micro controller
•Automatic tool recognition
•Digital display for PRE-SET and READ value (auto return)
•Temperature control from 50 to 450°C for soldering and
550°C for hot air
•Standard setback of 20 min. without WCB
•Calibration box can be connected for programming, time
setback and lock-out
•User Window – access to change temperature in lock-out
mode within a predefined range
•ESD confirm, protection class 1
•Accuracy ± 30°C for Hot Air Tools
± 2% of final value for Soldering Irons

WMD 1A
Hot Air Station
with integrated Pump
Consists of:
•Power Unit WMD 1S
with integrated
Rotation pump
•HAP 1 Hot Air Pencil 100
Watt
•AK10 Safety Rest

WMD 1A
Independent and Versatile
•Temperature setting infinitely
variable from 50 to 550°C
•Automatic Tool recognition
for tools up to 150 Watt
•Antistatic Metal box
•Potential balance (delivery
condition – direct grounded)
•Temp.Accuracy t ± 2% of final
value
•Maintain less free quick
starting Rotation Pump

WMD 1A
Soft Ware Function
•Automatic Tool recognition
corrects automatically physically based temperature variation of
different tools
•Automatic over load Protection
In case the electronic has to heat any tool uncontrolled for more
than 30 Min continuously, the power will be reduced to 80% to
avoid any damage.
•Setback
Temperature reduction to 150°C adjustable from 0 to 99 min.
•Offset
•To compensate temperature variations up to ±40°C

For large Packages
up to about 43 X 43 mm
HAP3000 hand - operated
Permanent connected
to....
WHA 900
without Nozzle
Vacuum
WHA 3000V
with Nozzle
Vacuum
WHA 3000P with
Nozzle Vacuum

HAP3000
Hot Air Nozzles
WHA 900 – no integrated
Vacuum possible
Mounted to....
WHA 3000V & WHA 3000P
• „Man“- Modus Press “VAC”
Button to activate the Nozzle
Vacuum
•„Auto “- Modus Nozzle
Vacuum will be activated
automatically in the end of the
Temperature Profile
Nozzle Vacuum

WHA 900
WHA 900
The portable Hot Air Station
for price conscious User

WHA 900
•Infinitely variable
Temperature setting from 50
to 550°C
•Continuously adjustable
airflow from 5 to 50 l / min.
•Stand -by parameter
unrestricted adjustable
•Offset setting at any
temperature possible
•Maintenance - free and
brushless turbine

WHA 900
Setting & Calibration
•Standby for constant nozzle
temperature and
elementary temperature
profile
•The only appliance within
that price level offering the
hot air calibration feature
•Offset scope ± 50°C

WHA 900
Stand By
•Activation
- set the desired parameter while the
appliance is in power off, keep
pushing the green button and power
on until the turbine reaches the final
speed.
- At active stand-by function the unit
will start with the predefined
parameter when powering on the
appliance
•Deactivation
- Push the green button and power
on the appliance, keep pushing the
button till the turbine stops.

WHA 900
einfaches Temperatur Profil
•Set stand-by Parameter and
activate
•Switch off the Appliance
•Position the hot air pencil,
( where applicable use
WHBS )
•Adjust desired soldering
Parameter
•Power on and wait until all
solder joints are properly
preheated
•Push start button and wait
until all solder joints are
reflowed
•Push stop button for the
final end
240°C
260°C
Power on start stop
Stand By setting Actual setting

WHA 900
Offset
•The adjustable offset scope is ± 50°C
•Calibration might be carried out at any desired
temperature.
Calibration Procedure
•Install temp. measurement nozzle, insert thermo
couple, and power on the appliance
•Set airflow to position 4 and air temperature to the
desired value
•Start operation (push green button) and wait until the
displayed temperature has been stabilized
•Push start button for about 15 sec. till the LED is
permanently illuminated
•Turn the setting potentiometer immediately to the
middle position. To correct any offset, by turning the
setting potentiometer slowly clock,- or counter
clockwise to meet the presetting.
•Push the green button to confirm and leave the offset
procedure.

For BGA Components
WHA 3000P Set
WHA 3000V Set
WHA 3000V
WHA 3000P

WHA 3000P
Self-Contained Hot Air Station
Consists of:
•Power Unit with HAP 3000
Hot Air Pencil 700 Watt
•Stop + Go Support AKT30
•Nozzle NQ30
•Nozzle Changer

WHA 3000P
complies to ESD Requirements
•Automatic and Manual Operating
Mode
•3-Step Temperature/Time Profile
•PC Connectivity & Remote
Control via RS232
•Socket for External Sensor
•Remote Control of WHP
•Digital Temperature Adjustment
from 50 to 550°C
•Green LED shows Heating
Pulses
•Air Flow adjustable
from 5 to 50 l/min
•Stand-by Function for Pre-
heating of Nozzles and
Components

WHA 3000V
Hot Air Station for Use of
Compressed Air or Inert Gas
Consists of:
•Power Unit with HAP 3000
Hot Air Pencil 700 Watt
Stop + Go Support AKT30
•Nozzle NQ30
•Nozzle Changer