Wenglor P1KY10 Series User manual

Operating Instructions
EN
Translation of the Original Operating Instruction
Subject to change without notice
Available as PDF version only
Version: 1.2.0
Status: 28.01.2019
www.wenglor.com
P1KY10x
High-Performance Distance Sensors

2Table of contents
Table of Contents
1. General ...................................................................................................................................3
1.1 Information Concerning these Instructions ............................................................................................. 3
1.2 Explanations of Symbols ......................................................................................................................... 3
1.3 Limitation of Liability................................................................................................................................. 4
1.4 Copyrights................................................................................................................................................ 4
2. For Your Safety.......................................................................................................................5
2.1 Use for Intended Purpose........................................................................................................................ 5
2.2 Use for Other than the Intended Purpose................................................................................................ 5
2.3 Personnel Qualifications .......................................................................................................................... 6
2.4 Modification of Products .......................................................................................................................... 6
2.5 General Safety Precautions ..................................................................................................................... 6
2.6 Laser/LED Warnings ................................................................................................................................ 6
2.7 Approvals and protection class ............................................................................................................... 6
3. Technical Data ........................................................................................................................7
3.1 Spot diameter........................................................................................................................................... 8
3.2 Switching Distance Deviation...................................................................................................................8
3.3 Accessory Products ................................................................................................................................. 8
3.4 Layout....................................................................................................................................................... 9
3.5 Control Panel.......................................................................................................................................... 10
3.6 Scope of Delivery ................................................................................................................................... 10
4. Transport and Storage .........................................................................................................10
4.1 Transport ................................................................................................................................................ 10
4.2 Storage................................................................................................................................................... 10
5. Installation and Electrical Connection................................................................................11
5.1 Installation .............................................................................................................................................. 11
5.2 Electrical Connection ............................................................................................................................. 11
5.3 Diagnostics............................................................................................................................................. 12
6. Settings.................................................................................................................................14
7. Settings via IO-Link..............................................................................................................15
7.1 Background Teach-In............................................................................................................................. 15
7.2 Window Teach-In ................................................................................................................................... 15
7.3 Locking................................................................................................................................................... 16
7.4 External Teach-In ................................................................................................................................... 16
7.5 Error Output ........................................................................................................................................... 16
8. IO-Link ..................................................................................................................................17
9. Maintenance Instructions ....................................................................................................17
10. Proper Disposal ...................................................................................................................17
11. Appendix...............................................................................................................................18
11.1 List of Abbreviations............................................................................................................................. 18
11.2 Change Index, Operating Instructions................................................................................................. 18
11.3 EU Declaration of Conformity .............................................................................................................. 18

3
High-Performance Distance Sensors
1. General
1.1 Information Concerning these Instructions
• These instructions apply to the product with ID code P1KY10x.
• They make it possible to use the product safely and efficiently.
• These instructions are an integral part of the product and must be kept on hand for the entire duration of
its service life.
• Local accident prevention regulations and national work safety regulations must be complied with as well.
• The product is subject to further technical development, and thus the information contained in
these operating instructions may also be subject to change. The current version can be found at
www.wenglor.com in the product’s separate download area.
NOTE!
The operating instructions must be read carefully before using the
product and must be kept on hand for later reference.
1.2 Explanations of Symbols
• Safety precautions and warnings are emphasized by means of symbols and attention-getting words
• Safe use of the product is only possible if these safety precautions and warnings are adhered to
The safety precautions and warnings are laid out in accordance with the following principle:
Attention-Getting Word!
Type and Source of Danger!
Possible consequences in the event that the hazard is disregarded.
• Measures for averting the hazard.
The meanings of the attention-getting words, as well as the scope of the associated hazards, are listed below.
DANGER!
This word indicates a hazard with a high degree of risk which, if not avoided, results in death
or severe injury.
WARNING!
This word indicates a hazard with a medium degree of risk which, if not avoided, may result
in death or severe injury.
CAUTION!
This word indicates a hazard with a low degree of risk which, if not avoided, may result in
minor or moderate injury.
ATTENTION!
This word draws attention to a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTE!
A note draws attention to useful tips and suggestions, as well as information regarding
efficient, error-free use.

4General
1.3 Limitation of Liability
• The product has been developed in consideration of the current state-of-the-art and applicable standards
and guidelines. Subject to change without notice.
• A valid declaration of conformity can be accessed at www.wenglor.com in the product’s separate down-
load area.
• wenglor sensoric elektronische Geräte GmbH (hereinafter referred to as “wenglor”) excludes all liability in
the event of:
• Non-compliance with the instructions
• Use of the product for purposes other than those intended
• Use by untrained personnel
• Use of unapproved replacement parts
• Unapproved modification of products
• These operating instructions do not include any guarantees from wenglor with regard to the described
procedures or specific product characteristics.
• wenglor assumes no liability for printing errors or other inaccuracies contained in these operating instruc-
tions, unless wenglor was verifiably aware of such errors at the point in time at which the operating instruc-
tions were prepared.
1.4 Copyrights
• The contents of these instructions are protected by copyright law.
• All rights are reserved by wenglor.
• Commercial reproduction or any other commercial use of the provided content and information, in particu-
lar graphics and images, is not permitted without previous written consent from wenglor.

5
High-Performance Distance Sensors
2. For Your Safety
2.1 Use for Intended Purpose
The product is based on the following functional principle:
High-Performance Distance Sensor
High-performance distance sensors which use the principle of transit time measurement determine the
distance between the sensor and the object according to the principle of transit time measurement. These
sensors have a large working range and are therefore able to detect objects over large distances.
This product can be used in the following industry sectors:
• Special machinery manufacturing
• Heavy machinery manufacturing
• Logistics
• Automotive industry
• Food industry
• Packaging industry
• Pharmaceuticals industry
• Plastics industry
• Woodworking industry
• Consumer goods industry
• Paper industry
• Electronics industry
• Glass industry
• Steel industry
• Aviation industry
• Chemicals industry
• Alternative energy
• Raw materials extraction
2.2 Use for Other than the Intended Purpose
• Not a safety component in accordance with 2006/42/EC (Machinery Directive)
• The product is not suitable for use in potentially explosive atmospheres.
• The product may only be used with accessories supplied or approved by wenglor, or combined with
approved products. A list of approved accessories and combination products can be accessed at
www.wenglor.com on the product detail page.
DANGER!
Risk of personal injury or property damage in case of use for other than the intended
purpose!
Use for other than the intended purpose may lead to hazardous situations.
• Observe instructions regarding use for intended purpose.

6For Your Safety
2.3 Personnel Qualifications
• Suitable technical training is a prerequisite.
• In-house electronics training is required.
• Trained personnel must have uninterrupted access to the operating instructions.
DANGER!
Risk of personal injury or property damage in case of incorrect
initial start-up and maintenance!
Personal injury and damage to equipment may occur.
• Adequate training and qualification of personnel.
2.4 Modification of Products
DANGER!
Risk of personal injury or property damage if the product is modified!
Personal injury and damage to equipment may occur. Non-observance may result
in loss of the CE marking and the guarantee may be rendered null and void.
• Modification of the product is impermissible.
2.5 General Safety Precautions
NOTE!
• These instructions are an integral part of the product and must be kept on hand
for the entire duration of its service life.
• In the event of possible changes, the respectively current version of the operating instruc-
tions can be accessed at www.wenglor.com in the product’s download area.
• Read the operating instructions carefully before using the product.
• Protect the sensor against contamination and mechanical influences.
2.6 Laser/LED Warnings
The respective laser class or LED group is listed in the product’s technical data.
LASER CLASS 1
EN 60825-1:2014
Laser Class 1 (EN 60825-1)
Invisible laser radiation.
Applicable standards and safety regulations must be observed.
2.7 Approvals and protection class
RoHS

7
High-Performance Distance Sensors
3. Technical Data
Optical Data
Working range 0…1500 mm
Setting range 50…1500 mm
Switching hysteresis < 30 mm
Light source Laser (infrared)
Wavelength 940 nm
Service life (ambient temp. = +25° C) 100000 h
Laser class (EN 60825-1) 1
Max. permissible ambient light 10000 Lux
Spot diameter see Table 1
Electrical Data
Supply power 10…30 V DC
IO-Link supply voltage 18…30 V DC
Current consumption (operating voltage = 24 V) < 15 mA
Switching frequency 10 Hz
Response time < 36 ms
Temperature drift < 2,5 %
Temperature range −30…50 °C
Number of switching outputs 2
Switching output voltage drop < 2,5 V
Switching output switching current 100 mA
Short-circuit protection yes
Reverse polarity protected yes
Overload-proof yes
Interface IO-Link
IO-Link version 1.1
Protection class III
Mechanical Data
Setting method Teach-in
Housing material Plastic
Lens cover PMMA
Degree of protection IP67/IP68
Technical Safety Data
MTTFd (EN ISO 13849-1) 2266,52 a
Order Number
Technical Data
P1KY1
01 03 02 04
Connection M8×1; 4-pin M12×1; 4-pin
Cable length — 200 mm
Suitable connection technology no. 7 2
Output Function PNP NO × ×
NPN NO ×* ×*
* The normally open NPN output function makes reference to switching output 1 (O1, pin 4). Switching output 2 (O2, pin 2) has a normally open
PNP output function.

8Technical Data
3.1 Spot diameter
Working distance 350 mm 700 mm 1500 mm
Spot diameter 14 mm 25 mm 42 mm
Table 1
3.2 Switching Distance Deviation
300 600 900 1200
1500
10
12
8
0
6
4
2
0
Sr/mm
dSr/mm
P1KY1
Typical characteristic curve based on Kodak white (90% remission)
Sr = switching distance
dSr = change in switching distance
Black, 6 % remission
Gray, 18 % remission
3.3 Accessory Products
wenglor can provide you with suitable connection technology for your product.
Suitable mounting technology no.
400
Suitable connection technology no.
7
2
S02
PNP-NPN converter BG7V1P-N-2M
IO-Link master
wTeach2 software DNNF005

9
High-Performance Distance Sensors
3.4 Layout
P1KY101, P1KY103
P1KY102, P1KY104
1 = receiver diode
2 = emitter diode
M3 screw = 0,5 Nm
Dimensions specified in mm (1 mm = 0.03937”)

10 Transport and Storage
3.5 Control Panel
A 23
06
5a 68 6a
06 = teach-in key
5a = switching status display, A1
6a = switching status display, A2
68 = supply power indicator
3.6 Scope of Delivery
• Sensor
• Safety precautions
• Mounting-Set 01
4. Transport and Storage
4.1 Transport
Upon receipt of shipment, the goods must be inspected for damage in transit. In the case of damage, con-
ditionally accept the package and notify the manufacturer of the damage. Then return the device, making
reference to damage in transit.
4.2 Storage
The following points must be taken into condition with regard to storage:
• Do not store the product outdoors.
• Store the product in a dry, dust-free place.
• Protect the product against mechanical impacts.
• Protect the product against exposure to direct sunlight.
ATTENTION!
Risk of property damage in case of improper storage!
The product may be damaged.
• Storage instructions must be complied with.

11
High-Performance Distance Sensors
5. Installation and Electrical Connection
5.1 Installation
• Protect the product from contamination during installation.
• Observe all applicable electrical and mechanical regulations, standards, and safety rules.
• Protect the product against mechanical influences.
• Make sure that the sensor is mounted in a mechanically secure fashion.
• Specified torque values must be complied with see section “3. Technical Data”, page 7.
ATTENTION!
Risk of property damage in case of improper installation!
The product may be damaged.
• Installation instructions must be complied with.
CAUTION!
Risk of personal injury or property damage during installation!
Personal injury and damage to the product may occur.
• A safe installation environment must be assured.
5.2 Electrical Connection
Connect the sensor to supply voltage see section “3. Technical Data”, page 7.
P1KY101, P1KY102 P1KY104
223
E A2
NPN
NO NC
239
1
4
2
3
E A1
PNP
NO NC

12 Installation and Electrical Connection
DANGER!
Risk of personal injury or property damage due to electric current!
Voltage conducting parts may cause personal injury or damage to equipment.
• The electric device may only be connected by appropriately qualified personnel.
5.3 Diagnostics
Causes for Triggering the Contamination Warning (blinking LED):
Display LED Diagnosis/Cause Elimination
Continuous blinking
at approx. 2.5 Hz
Contamination Carefully clean the optic cover with a cloth.
Aged emitter diode Replace the sensor.
Unreliable working range • Increase the sensor’s switching distance.
• Reduce distance between sensor and object.
Continuous blinking
at approx. 5 Hz
Short-circuit Check electrical wiring and eliminate the short-circuit.
Over-temperature Disconnect the sensor from supply power
and allow it to cool down.
Hardware error Replace the sensor.

13
High-Performance Distance Sensors
Contamination Warning Flowcharts
not detected not detecteddetected
beginning contamination
Object Object Object
not detected not detecteddetected
Transmit Time Sensor no contamination
Object Object Object
Object
Switching Status
Indicator
Object
Switching Status
Indicator
Object
Switching Status
Indicator
not detected not detectednot detected
advanced contamination
Object Object Object
off offon
off off
off off
blinking
off
Required action in case of fault:
NOTE!
• Shut down the machine.
• Analyze and eliminate the cause of error with the help of the diagnostics information.
• If the error cannot be eliminated, please contact wenglor’s support department.
• Do not operate in case of indeterminate malfunctioning.
• The machine must be shut down if the error cannot be unequivocally clarified or reliably
eliminated.
DANGER!
Risk of personal injury or property damage in case of non-compliance!
The system’s safety function is disabled. Personal injury and damage to equipment.
• Required action as specified in case of fault.

14 Settings
6. Settings
The switching distance to the object can be taught in for both outputs by pressing the teach-in key on the
sensor (foreground teach-in).
Object
Sensor
Teach-in distance
Switching point
Foreground Teach-In for Switching Output 1
1. Mount the sensor in accordance with the mounting instructions.
2. Position the object in front of the sensor.
3. Press and hold the teach-in key until switching status indicator LED A1 starts blinking.
4. Release the teach-in key after 2 seconds.
5. The distance is taught in and the LED at output 1 lights up in order to confirm successful teach-in.
Foreground Teach-In for Switching Output 2
1. Mount the sensor in accordance with the mounting instructions.
2. Position the object in front of the sensor.
3. Press and hold the teach-in key until switching status indicator LED A2 starts blinking.
4. Release the teach-in key after 5 seconds.
5. The distance is taught in and the LED for output 2 lights up in order to confirm successful teach-in.
NOTE!
If teach-in is conducted without an object or if the object is too far from the sensor, switching
distance is set to the end of the setting range.

15
High-Performance Distance Sensors
7. Settings via IO-Link
Further settings can be entered to the sensor via the IO-Link interface.
7.1 Background Teach-In
In addition to foreground teach-in (default setting), there’s also a background teach-in option for both outputs.
1. Align the sensor to the background.
2. Enter or teach in the switching point.
3. The sensor is switched as soon as an object is located between the background and the sensor.
Object
Switching Point
Sensor
Teach Distance
7.2 Window Teach-In
Additionally, there’s also a window teach-in option for both outputs:
1. Enter or teach in the far switching point.
2. If necessary, adjust the window with the near and far switching points.
3. The sensor is switched when an object is located between the two switching points.
Object
Sensor
Teach-in distance
Switching point
Window
Size
Window’s near
switching point
Window’s far
switching point
If the teach-in mode is selected, the switching point can be taught in by pressing the teach-in key.

16 Settings via IO-Link
7.3 Locking
If 18 to 30 V DC is continuously applied to the teach-in input, the teach-in key is locked and protected against
inadvertent changes.
1. Change the A2 pin function to external teach-in.
2. Permanently connect pin A2 to voltage within a range of 18 to 30 V DC.
3. The sensor is protected against inadvertent changes caused by the teach-in key.
7.4 External Teach-In
Teach in output A1 via the teach-in input.
1. Set the A2 pin function to external teach-in.
2. Apply 24 V to pin A2 for at least 1 second, but for no more than 4 seconds.
3. As soon as voltage drops at the input, A1 is taught in.
7.5 Error Output
The error output is switched in the following cases:
• Signal from object too weak
• Incorrect installation
• The object is located outside of the working range.
• Short-circuit
• Over-temperature

17
High-Performance Distance Sensors
8. IO-Link
Process and parameters data, as well as the IODD, can be found at www.wenglor.com in the product’s sepa-
rate download area.
9. Maintenance Instructions
NOTE!
• This wenglor sensor is maintenance-free.
• Cleaning and inspection of the plug connections at regular intervals are advisable.
• Do not clean the sensor with solvents or cleansers which could damage the product.
• The product must be protected against contamination during initial start-up.
10.Proper Disposal
wenglor sensoric GmbH does not accept the return of unusable or irreparable products. Respectively valid
national waste disposal regulations apply to product disposal.

18 Appendix
11.Appendix
11.1 List of Abbreviations
Abbreviation Meaning
Tu Ambient temperature
Ub Supply voltage
IODD IO Device Description
MTTFd Mean Time to Dangerous Failure
11.2 Change Index, Operating Instructions
Version Date Description/Change
1.0.0 29.06.17 Initial version of the operating instructions
1.1.0 18.12.17 see section “7. Settings via IO-Link”, page 15
1.2.0 15.01.19 New versions added, see section “3. Technical Data”, page 7
11.3 EU Declaration of Conformity
The EU declaration of conformity can be found on our website at www.wenglor.com in the product’s down-
load area.