Weslo Momentum 2000 Elliptical User manual

USERʼS MANUAL
Serial Number
Decal
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Model No. WLEVEL72808.0
Serial No.
Write the serial number in the
space above for reference.
QUESTIONS?
As a manufacturer, we are commit-
ted to providing complete customer
satisfaction. If you have questions,
or if there are missing parts, please
contact us at the numbers or
addresses listed below:
Call: 08457 089 009
Outside UK: 0 (44) 113 3877133
Fax: [phone]
E-mail: [email protected]
Write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road, Beeston
Leeds, LS11 8 G
UK

TABLE OF CONTENTS
WARNINGDECALPLACEMENT ..............................................................2
IMPORTANTPRECAUTIONS ................................................................3
BEFOREYOUBEGIN ......................................................................4
ASSEMBLY ...............................................................................5
HOWTOUSETHEELLIPTICALEXERCISER ..................................................10
MAINTENANCEANDTROUBLESHOOTING ...................................................14
EXERCISEGUIDELINES ...................................................................15
PARTLIST ..............................................................................18
EXPLODEDDRAWING ....................................................................19
ORDERINGREPLACEMENTPARTS ..................................................BackCover
2
WESLO is a registered trademark of ICON IP, Inc.
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing
or illegible, call the telephone number
on the front cover of this manual and
request a free replacement decal.
Apply the decal in the location
shown. Note: The decal(s) may not be
shown at actual size.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
IMPORTANT PRECAUTIONS
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over the age of 35 or
persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. Your elliptical exerciser is intended for home
use only. Do not use your elliptical exerciser
in a commercial, rental, or institutional set-
ting.
4. Keep your elliptical exerciser indoors, away
from moisture and dust. Place your elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around your elliptical exerciser to mount,
dismount, and use it.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from your elliptical exerciser at all times.
7. Your elliptical exerciser should not be used
by persons weighing more than 250 lbs.
(113 kg).
8. Wear appropriate exercise clothes when
exercising; do not wear loose clothes that
could become caught on your elliptical exer-
ciser. Always wear athletic shoes for foot
protection.
9. Hold the handgrip pulse sensor or the handle-
bars when mounting, dismounting, or using
your elliptical exerciser.
10. Keep your back straight while using your
elliptical exerciser; do not arch your back.
11. The pulse sensor is not a medical device.
Various factors, including the userʼs move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
12. When you stop exercising, allow the pedals
to slowly come to a stop.
13. If you feel pain or dizziness while exercising,
stop immediately and cool down.
14. Use your elliptical exerciser only as
described in this manual.

4
BEFORE YOU BEGIN
Congratulations for selecting the new WESLO®
MOMENTUM 2000 elliptical exerciser. The MOMEN-
TUM 2000 elliptical exerciser provides a wide array of
features designed to make your workouts at home
more effective and enjoyable.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the
product model number and serial number before con-
tacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Handlebar
Pedal Disc
Pedal
Console Pulse Sensor

5
M10
Washer (35)–2
M10 Split
Washer (59)–2
M10 Locknut
(33)–6
Pedal Arm Bolt Set (40)–2
M6 Locknut
(27)–4
M10 x 25mm
Patch Screw (22)–2
M10 x 70mm Carriage Bolt (34)–4M10 x 68mm Button Bolt (48)–2
M6 x 36mm Button Bolt (50)–4
M6 x 48mm Flat Head
Screw (36)–4
Wave Washer
(58)–2
M6 x 12mm
Screw (43)–4
ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tools, assembly requires a Phillips screwdriver , an adjustable
wrench , a rubber mallet , and pliers .
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parenthe-
ses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The
number following the parentheses is the quantity needed for assembly. Note: Some small parts may have
been preassembled. If a part is not in the hardware kit, check to see if it has been preassembled.

6
1.
Identify the Front Stabilizer (10), which is nar-
rower than the Rear Stabilizer (not shown).
While another person lifts the front of the Frame
(1), attach the Front Stabilizer to the Frame with
two M10 x 70mm Carriage Bolts (34) and two
M10 Locknuts (33).
10
33
34
1
1
33
2. While another person lifts the back of the Frame
(1), attach the Rear Stabilizer (28) to the Frame
with two M10 x 70mm Carriage Bolts (34) and
two M10 Locknuts (33).
34
28
1
2
33
33
3. The Console (23) can use four “AA” batteries
(not included); alkaline batteries are recom-
mended. IMPORTANT: If the Console has
been exposed to cold temperatures, allow it
to warm to room temperature before insert-
ing batteries. Otherwise, you may damage
the console displays or other electronic
components. Remove the battery cover, insert
the batteries into the battery compartment, and
reattach the battery cover. Make sure to orient
the batteries as shown by the diagram
inside the battery compartment.
23
Batteries
Battery
Cover
3
To make assembly easier, read the
information on page 5 before you begin
assembling the elliptical exerciser.

7
4. While another person holds the Console (23)
near the Upright (2), connect the console wire
to the Upper Wire (44). Then, insert the wires
into the Upright.
Tip: Avoid pinching the wires. Attach the
Console (23) to the Upright (2) with four M6 x
12mm Screws (43).
4
23
2
44Console Wire
43
5
1
2
33
Avoid pinching
the wires
Avoid pinching
the wires
44
63
48
59
5. While another person holds the Upright (2) near
the Frame (1), connect the Upper Wire (44) to
the Lower Wire (63). Then, push the excess
wire downward into the Frame.
Tip: Avoid pinching the wires. Slide the
Upright (2) onto the Frame (1). Attach the
Upright with two M10 x 68mm Button Bolts (48),
two M10 Split Washers (59), and two M10
Locknuts (33). Do not tighten the Button
Bolts yet.

8
50
8
27
6. Identify the Left Handlebar (6), which is marked
with a sticker. Insert the Left Handlebar into one
of the Handlebar Arms (5); make sure that the
Handlebar Arm is turned so the hexagonal
holes are on the indicated side.
Attach the Left Handlebar (6) to the Handlebar
Arm (5) with two M6 x 36mm Button Bolts (50)
and two M6 Locknuts (27). Make sure that the
Locknuts are inside the hexagonal holes. Do
not fully tighten the Button Bolts yet.
Apply a small amount of the included grease to
the left axle on the Upright (2).
Make sure that there are two Small Handlebar
Bushings (49) in the Left Handlebar (6). Slide a
Handlebar Spacer (47) and the Left Handlebar
onto the left axle on the Upright (2) as shown.
Make sure that the Handlebar Spacer is
turned so the curved side is facing the
Upright. Tap an Axle Cap (14) onto the axle.
Repeat this step to assemble the Right
Handlebar (8) and the other Handlebar Arm
(5).
Grease
6
47
14
49
5
2
5
6
7
36
11
13
7. Identify the Left Pedal Arm (11), which is
marked with a “Left” sticker. Attach a Pedal (13)
to the Left Pedal Arm with two M6 x 48mm Flat
Head Screws (36).
Attach the other Pedal to the Right Pedal
Arm (not shown) in the same way.
Hexagonal
Holes

9
9. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical exerciser.
8. Apply a small amount of grease to the axle on
the left Disc Crossbar (16). Slide the Left Pedal
Arm (11) onto the axle, and place a Wave
Washer (58) on the end of the axle. Next, slide
an M10 Washer (35) onto an M10 x 25mm
Patch Screw (22), and tighten the Patch Screw
into the axle.
Apply grease to a Pedal Arm Bolt Set (40).
Next, hold the lower end of the left Handlebar
Arm (5) inside the bracket on the Left Pedal
Arm (11). Attach the Left Pedal Arm to the left
Handlebar Arm with the Bolt Set. Do not over-
tighten the Bolt Set; the Handlebar Arm
must pivot freely.
Attach the Right Pedal Arm (not shown) to
the right side of the elliptical exerciser in the
same way.
See step 5. Tighten the M10 x 68mm Button
Bolts (48).
See step 6. Tighten the M6 x 36mm Button
Bolts (50) in the Handlebar Arms (5).
Grease
Grease
22 35
11
5
8
40
40
58
16

10
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
To mount the elliptical exerciser, hold the handlebars
and step onto the pedal that is in the lowest position.
Then, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion. Note:
The pedal discs can turn in either direction. It is
recommended that you move the pedal discs in
the direction shown by the arrow; however, for
variety, you may turn the pedal discs in the oppo-
site direction.
To dismount the elliptical exerciser, wait until the ped-
als come to a complete stop. Note: The elliptical
exerciser does not have a free wheel; the pedals
will continue to move until the flywheel stops.
When the pedals are stationary, step off the highest
pedal first. Then, step off the lower pedal.
Pedal Disc
Pedal
Handlebars