Westin PRO TRAXX 5 User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-215408-RevB ECO #: W18-0090 DATE: 07/26/18
INSTALLATION INSTRUCTIONS
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
1,2 2 STEP BAR ASSEMBLY (1 DRIVER, 1 PASSENGER) 10MM SOCKET
3 2 MOUNTING BRACKET A 10MM WRENCH
4 1 MOUNTING BRACKET B 13MM SOCKET
5 6 MOUNTING BRACKET C RATCHET
6 3 MOUNTING BRACKET D TORQUE WRENCH
7 6 PLASTIC COVER BRACKET
8 12 M10 BUTTON HEAD SCREW
9 12 M10 INTERNAL TOOTHED LOCK WASHER
10 12 M10 FLAT WASHER
11 24 M8 HEX NUT
12 24 M8 FLAT WASHER
13 24 M8 SPLIT LOCK WASHER
14 6 M8 ROUND HEAD SQUARE NECK BOLT
15 12 M6 HEX HEAD CAP SCREW
16 24 M6 FLAT WASHER
17 12 M6 NYLON NUT
18 18 PLASTIC RETAINER SQUARE
19 1 HEX KEY TOOL
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
CONTENT
PRO TRAXX 5 OVAL STEP BAR
APPLICATION:
2019 Ram 1500 Crew Cab
PART NUMBER:
21-54080, 21-54085, 21-54090, 21-54095
ITEM 1
ITEM 3 ITEM 4 ITEM 5 ITEM 6

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-215408-RevB ECO #: W18-0090 DATE: 07/26/18
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
2. Preassemble the Mounting Brackets (3-6). Do not tighten hardware at this time. See Figure 1.
Fig. 1
Mounting Bracket D Shown
Other Brackets Assemble Similarly
6
5
13
11
12
14

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-215408-RevB ECO #: W18-0090 DATE: 07/26/18
3. Starting on the passenger side of the vehicle, locate the 3
mounting locations on the rocker panel.
Note A: The rear mounting location is shown in Figure 2. Other
mounting locations are similar.
Note B: The lower two studs on the rocker panel have a thick
coat of paint on them. When installing the M8 hex nuts, apply
extra pressure to start. If necessary, back M8 hex nuts off the
studs to clear build up.
See Figure 2.
Fig. 2
Rear Mounting Location Shown
Other Mounting Locations are Similar
4. At the rear mounting location, loosely install Mounting Bracket D (6) with preassembled Mounting Bracket C (5) using the
supplied M8 hardware. See Figures 3 & 4.
Rocker Panel
Fig. 3 Fig. 4
Front Passenger Shown Rocker Panel
5
13
13
5
11
12
11
11
12
14

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-215408-RevB ECO #: W18-0090 DATE: 07/26/18
5. At the center passenger mounting location, loosely install Mounting Bracket A (3) with preassembled Mounting Bracket C
(5) using the supplied M8 hardware. See Figures 5 & 6.
6. At the front passenger mounting location, loosely install Mounting Bracket B (4) with preassembled Mounting Bracket C
(5). Note: Installation is similar to Mounting Bracket D.
7. Repeat Steps 4-7 on the driver side of the vehicle.
Fig 5 Fig 6 Pinch Weld
Pinch Weld
7
5
13
5
13
14
11
11
12
11
12

5
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-215408-RevB ECO #: W18-0090 DATE: 07/26/18
8. Secure the Plastic Cover Brackets (7) to the Mounting Brackets using the supplied M6 Hardware. See Figure 7
9. Fasten oval tube step bars respectively to either side using the M10 hardware provided with the step bars. See Figure 8.
10. Align and adjust the step bars as needed and fully tighten all hardware. Torque all M6 fasteners to 5-7 ft-lbs, all M8
fasteners to 15-18 ft-lbs, and all M10 fasteners to 30 ft-lbs.
Fig 7 Fig 8
INSTALLATION COMPLETE

6
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-215408-RevB ECO #: W18-0090 DATE: 07/26/18
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
WARNING
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY:
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight rating regardless
of the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL
AS VEHICLE DAMAGE.