Whalen WMCXL-2 User manual

Whalen Furniture Mfg. Inc. Page 1 Factory No. 33-10944
44” 3-in-1 Console (WMCXL-2)
This item is designed to be 3-in-1 configuration. Please choose which of the 3 options suits your
needs. DO NOT discard any of the hardware or parts that you will not use on your set option, this
will give you the opportunity to use this TV Console for different configurations in case you decide
to upgrade your TV set in the future.
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if you are missing parts, do not return this item to
the Retailer Store. Please call our toll-free customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
1-866-942-5362 8:30 a.m. - 4:30 p.m. PST, Monday - Friday
ONLINE: www.whalenfurniture.com EMAIL: [email protected]
Video Instruction Guides
Go to http://whalen.showuhow.com to view step-by-step instructional
videos for assembling and installing your product. Enter the following
product number on the ShowUhow homepage.
LOT NUMBER:
DATE PURCHASED: / /
Option 1
With Swinging Floater
XL-2 or WMCXL-2

Model # WMCXL-2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc. Page 2 Factory No. 33-10944
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
MANUFACTURER: Whalen Furniture
CATALOG: 44” 3-in-1 Console (WMCXL-2)
DATE OF MANUFACTURE: December, 2010
MADE IN CHINA
FITS UP TO MOST 50” FLAT PANEL TV’S
MAXIMUM LOAD 135 lb. (61.2 kg)
FITS UP TO MOST 50” FLAT PANEL TV’S
WITHOUT SWIVELING BRACKET
MAXIMUM LOAD 135 lb. (61.2 kg)
MAXIMUM LOAD 50 lb. (22.7 kg)
1. Please read the Assembly Instructions prior to assembling this product.
2. Remove all hardware from box and sort by size.
3. Check to see that all hardware and parts are present BEFORE assembling.
4. Ask a friend to assist you with the assembly of this furniture.
5. To avoid damage, assemble the product on a sturdy, level and protective surface.
6. Please wait until all steps are completed before tightening bolts.
7. Make sure all bolts are tightly fastened before the unit is used.
THIS UNIT IS INTENDED FOR USE ONLY WITH THE PRODUCTS
AND MAXIMUM WEIGHTS INDICATED. USE WITH OTHER PRODUCTS OR PRODUCTS
HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY
CAUSING POSSIBLE INJURY. THE BASE OF THE TELEVISION MUST BE PLACED
SQUARELY IN THE CENTER OF THE STAND WITH NO OVERHANGING ON EITHER SIDE.
IMPORTANT INFORMATION
GENERAL INFORMATION, TIPS & TRICKS
This product is sold with Tip Restraint Hardware kit. You must install the Tipping Restraint
Hardware between the wall and the TV stand to prevent any accidents or damages. When
properly installed, this restraint can provide protection against the unexpected tipping of the
unit due to small tremors, bumps or climbing. The restraint is only a deterrent and is not a
substitute for proper adult supervision. Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.

Model # WMCXL-2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc. Page 3 Factory No. 33-10944
Parts and Hardware List
Please read completely through the instructions and verify that all parts listed are present
before beginning assembly.
A-Top Shelf Frame (1) B- Middle Shelf Frame (1) C- Bottom Shelf Frame (1)
D- Long Spine (1) D1- Short Spine (1) E- Left “L” Shape Leg (1)
F- Left Front Leg (1) G- Right “L” Shape Leg (1) H- Right Front Leg (1)
I- Top Glass Shelf (1) J- Middle Glass Shelf (1) K- Bottom Glass Shelf (1)
L- Swiveling Bracket (1) M- XYZ Mounting Frame (1) N- Monitor Bracket (2)
O- Safety Bar (1) P- Decorative Rail (2)

Model # WMCXL-2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc. Page 4 Factory No. 33-10944
Parts and Hardware List
(1) - Suction Cup (2) - 3/4” Bolt (3) - 1 1/4” Bolt (4) - Hex Nut
(20+1 extra) (18+1 extra) (16+1 extra) (4+1 extra)
(5) -Black Lock Washer (6) - Zinc Lock Washer (7) –Black Flat Washer (8) - Zinc Flat Washer
(14+1 extra) (14+1 extra) (18+1 extra) (14+1 extra)
(9)- Large Flat Washer (10) - 2 1/2” Lag Bolt (11) - Concrete Anchor (12) - Cable Control
(6) (6) (6) (2)
(13) - 1” Bolt Open Wrench Allen Wrench Tipping Restraint Hardware Kit (1)
(4+1 extra) (1) (1) (Inside Plastic Bag)
TV Mounting Kit
M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 X 12 Bolt (4) M5 x 30 Bolt (4)
M6 x12 Bolt (4) M6 x 35 Bolt (4) M8x16 Bolt (4) M8 x40 Bolt (4)
M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)
Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)
Tools required: Allen Wrench (provided) and Open Wrench (provided), Phillips Head
Screwdriver, Mallet, Power Drill, 3/8” & 3/16”Drill Bit, Socket Wrench Adapter with
Socket Set, 1/2” Masonry Bit for brick concrete, Stud Sensor.

Model # WMCXL-2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc. Page 5 Factory No. 33-10944
Assembly Instructions
Note: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make it easier during assembly of unit.
1. Unpack the unit and confirm that you have all the hardware and parts required.
2. Align the bottom bracket holes of Left “L” Shape Leg (E) with the sockets on the Left Front
Leg (F). Make sure the upper tube of “L” Shape Leg fits into the cutout of Left Front Leg
properly. Attach in place by inserting two 3/4” Bolts (2) with Black Washers (5 & 7) into the
bracket holes. Tighten the bolts with the Allen Wrench provided. See detail #1.
3. Repeat last step to combine the Right “L” Shape Leg (G) with Right Front Leg (H) together.
4. Attach 2 Decorative Rails (P) to the bottom of Long Spine (D) using six 1 1/4” Bolts (3).
Tighten with the Allen Wrench provided. See detail #1A. (Note: If you choose table-top
configuration, please ignore this step.)
Required hardware in this step
Description: (2) –3/4” Bolt (3) –1 1/4” Bolt (5) –Black Lock Washer (7) –Black Flat Washer
Sketch
Qty. (4 pcs) (6 pcs) (4 pcs) (4 pcs)
Tools required: Allen Wrench

Model # WMCXL-2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc. Page 6 Factory No. 33-10944
Assembly Instructions
5. Choose the option suits your needs. Locate Long Spine (D) or Short Spine (D1) and set
back face down on a scratch free surface as shown in detail #2.
6. Align the holes on back rail of 3 Shelf Frames (A, B & C) with the sockets on the Spine.
Insert and screw 1 1/4”Bolts (3) with Zinc Lock Washers & Flat Washers (6 & 8) through the
pre-drilled holes on back rail into the Spine. Make sure the corner plates for Suction Cup on
each Shelf Frame will face up after assembly. See detail #2.
Required hardware in this step
Description: (3) –1 1/4” Bolt (6) –Zinc Lock Washer (8) –Zinc Flat Washer
Sketch
Qty. (6 pcs) (6 pcs) (6 pcs)
Tools required: Allen Wrench

Model # WMCXL-2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc. Page 7 Factory No. 33-10944
Assembly Instructions
7. Stand the unit upright.
8. Align and attach Left Leg Assembly to the Top Shelf Frame (A) using two 1” Bolts (13) with
Zinc Washers (6 & 8) through the pre-drilled holes on inner side rail into the top of both Legs.
See detail #3. DO NOT tighten the bolts.
9. Secure Left Leg Assembly to Middle & Bottom Shelf Frame (B & C) using the 1 1/4” Bolts (3)
with Zinc Washers (6 & 8) from inside the shelf frame into the sockets included on the side
of Legs. See detail #3A.
10.Repeat last 2 steps to attach Right Leg Assembly at the other end.
Required hardware in this step
Description: (13)- 1” Bolt (3) –1 1/4” Bolt (6) –Zinc Lock Washer (8) –Zinc Flat Washer
Sketch
Qty. (4 pcs) (4 pcs) (8 pcs) (8 pcs)
Tools required: Allen Wrench

Model # WMCXL-2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc. Page 8 Factory No. 33-10944
Assembly Instructions
11.Go back and tighten all bolts with Allen Wrench provided.
12.In case of uneven floor, Floor Levelers are provided at the bottom of both Front Legs (F & H).
Simply tilt the unit back and raise or lower floor leveler by hand to correct tilting as shown in
detail #4.
Hardware provided Tools required
Pre-attached Floor Leveler No tool required
If you choose Table-top configuration,
continue to STEP 13.
If mounting TV with the Swinging Floater,
skip ahead to PAGE 12.

Model # WMCXL-2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc. Page 9 Factory No. 33-10944
Assembly Instructions for Table-top
13.Attach 2 Cable Controls (12) onto the backside of Spine (D1) with the 3/4” Bolts (2). Tighten
the bolts with the Allen Wrench provided. See detail #5.
14.The Cable Controls (12) enable you to shorten, separate and route cables and cords. Using
the Cable Controls you can create a system for routing cables through channels, between
components and to power sources without usual tangled mess or annoying signal
interference. As shown in detail #5.
Required hardware in this step
Description: (2) - 3/4” Bolt (12) –Cable Control
Sketch
Qty. (4 pcs) (2 pcs)
Tools required: Allen Wrench

Model # WMCXL-2
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg. Inc. Page 10 Factory No. 33-10944
Assembly Instructions for Table-top
15.Put Suction Cups (1) firmly into the top holes and corner plates on 3 Shelf Frames (A, B & C)
as shown in detail #6.
16.Place Top Glass (I) and Glass Shelves (J & K) in place as shown in detail #6. Make sure the
glass is properly centered and the black side of glass is down. Push each glass all the way
back against the Spine. Also, be sure to press down evenly and firmly each glass onto the
Suction Cups to make sure they securely rest onto the Suction Cups.
Note: Make sure that the Suction Cups go all the way into the pre-drilled holes to prevent the
glass shelf from falling and getting damage. If glass is scratched you can minimize the
damage by using a BLACK marker and filling in scratched area from underneath.
Required hardware in this step
Description Sketch Qty.
(1) –Suction Cup (20 pcs)