Whalen BBXL54NV User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Manufacturing Page 1 Factory No. 16434
Date 2014-09-17 Rev. 1 Factory: DOSHFU
3-IN-1TM TV Console
Model # BBXL54NV
U.S. Patent 8,561,551
This item is designed to be a 3-in-1 configuration. Please choose the option that best suits your
needs. DO NOT discard any of the hardware or parts that you will not use on your chosen option.
This will allow you to use this TV Console in different configurations at a later date, if desired.
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to
the store where it was purchased. Please call our toll-free customer service number and have
your instructions and parts list ready to provide the model name, part name or factory number:
8:30 a.m. - 4:30 p.m., PST, Monday - Friday
ONLINE: www.whalenfurniture.com EMAIL: [email protected]
On-line Video Instruction Guides
Go to http://vig.sellpoints.com to view step-by-step instructional
videos for assembling and installing your product. Enter the
following product number on the website under Whalen brand.
LOT NUMBER:
DATE PURCHASED: / /
BBXL54NV

Model # BBXL54NV
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 2 Factory No. 16434
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: 3-IN-1TM TV Console (BBXL54NV)
DATE OF MANUFACTURE: September 2014
MADE IN CHINA
1. Please read the Assembly Instructions prior to assembling this product.
2. Remove all hardware from the box and sort by size.
3. Check to see that all hardware and parts are present BEFORE assembling.
4. Ask a friend to assist you with the assembly of this furniture.
5. To avoid damage, assemble the product on a sturdy, level and protective surface.
6. Please wait until all steps are completed before fully tightening Bolts.
7. Make sure all Bolts are tightly fastened before the unit is used.
MAXIMUM RECOMMENDED WEIGHT LOADS
FITS UP TO MOST 65” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.2 kg)
FITS UP TO MOST 65” FLAT PANEL TVs
WITHOUT SWIVELING BRACKET
MAXIMUM LOAD 135 lb. (61.2 kg)
MAXIMUM LOAD 50 lb. (22.6 kg)
GENERAL INFORMATION
,
TIPS and TRICKS
This product is sold with one set of Tipping Restraint Hardware Kit. You must install the
Tipping Restraint Hardware between the wall and the TV console to prevent any accidents or
damages. When properly installed, this restraint can provide protection against the
unexpected tipping of the unit due to small tremors, bumps or climbing. The restraint is only a
deterrent and is not a substitute for proper adult supervision. Use of tip-over restraints may
only reduce, but not eliminate, the risk of tip-over.
PLACE TV BEHIND THE STOPPER
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY
WITH FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE
AND WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT
PANEL TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE
CENTRE OF THE UNIT; THE BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE
SUPPORTING SURFACE OF THE UNIT WITHOUT OVER-HANGING THE EDGES.
IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS OR OTHER
EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS COULD FALL OFF
OR BREAK THE UNIT
,
CAUSING POSSIBLE SERIOUS INJURY.

Model # BBXL54NV
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 3 Factory No. 16434
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware
are present before beginning assembly.
A-Top Shelf Frame (1) B- Middle Shelf Frame (1) C- Bottom Shelf Frame (1)
D- Spine Assembly (1) E- Left Leg (1) F- Right Leg (1)
G- Top Glass (1) H- Glass Shelf (2) I- Swiveling Bracket (1)
J- Mounting Frame (1) K- Monitor Bracket (2) L- Cable Wheel (2)
(1) Suction Cup (2) 1/2” Bolt (3) 5/8” Bolt (4) 1” Bolt
(24+1 extra) (4+1 extra) (16+1 extra) (8+1 extra)
(5) 2-1/2” Bolt (6) Lock Washer (7) Flat Washer (8) Flange Nut
(1+1 extra) (17+1 extra) (17+1 extra) (1+1 extra)

Model # BBXL54NV
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 4 Factory No. 16434
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware
are present before beginning assembly.
(9) 1-3/4” Wood Screw (4+1 extra) (10) Concrete Anchor (4) (11) 2-1/2” Lag Bolt (4)
(12) Large Flat Washer (4+1 extra) (13) Spine End Cap (1) (14) Acrylic Stopper (1)
M4 Allen Wrench (2) Touch-up Pen (1) Tipping Restraint Hardware Kit (1)
(Inside Plastic Bag)
TV Mounting Kit
M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 x 12 Bolt (4) M5 x 30 Bolt (4)
M6 x 12 Bolt (4) M6 x 35 Bolt (4) M8 x 16 Bolt (4) M8 x 40 Bolt (4)
M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)
Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)
Tools required: Allen wrench (provided) and Phillips screwdriver (not provided).

Model # BBXL54NV
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 5 Factory No. 16434
Assembly Instructions
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Locate the Spine Assembly (D) and set the back face down on a scratch-free surface, as shown.
3. Align and attach the Shelf Frames (A, B and C) to the Spine (D) respectively, as shown above.
Make sure the inside corner plates and the metal tabs on the shelf frames (A, B and C) will
face up when the unit is turned upright.
37
4
4
1” Bolt
(4 used in this step)
④
Lock Washer
(2 used in this step)
⑥
Flat Washer
(2 used in this step)
⑦
5/8” Bolt
(2 used in this step)
③

Model # BBXL54NV
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 6 Factory No. 16434
Assembly Instructions
4. Stand the last assembly upright.
5. Align and attach the Left Leg (E) to the lower shelf frames (B and C) by inserting two 1” Bolts
(4) from inside of the shelf frames. Secure the Left Leg (E) to the Bottom Shelf Frame (C) by
using one 5/8” Bolt (3) with the Washers (6 and 7) through the metal bracket and screw into
place. DO NOT tighten the bolts in this step.
6. Securely fasten the Top Shelf Frame (A) to the Left Leg (E) with two 1-3/4” Wood Screws (9).
7. Repeat the same procedure to attach the Right Leg (F) at the opposite end.
1” Bolt
(4 used in this step)
④
1-3/4” Wood Screw
(4 used in this step)
⑨
5/8” Bolt
(2 used in this step)
③
Lock Washer
(2 used in this step)
⑥
Flat Washer
(2 used in this step)
⑦
C
D
E
4

Model # BBXL54NV
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 7 Factory No. 16434
Assembly Instructions
8. Secure the Top Shelf Frame (A) to the inner metal legs (E and F), using two 5/8” Bolts (3) with
the Washers (6 and 7) through the top metal plate of each leg and securely screw into the Top
Shelf Frame (A). As shown above.
5/8” Bolt
(4 used in this step)
③
Lock Washer
(4 used in this step)
⑥
Flat Washer
(4 used in this step)
⑦

Model # BBXL54NV
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 8 Factory No. 16434
Assembly Instructions
9. Go back and tighten all bolts with the enclosed Allen Wrench.
10.If necessary, adjust the pre-attached Floor Levelers at the bottom of both Legs (E and F) to
level the unit.
If you choose the Table-top configuration,
continue to the next step.
If mounting the TV to the Floating Swivel
Mount, skip ahead to PAGE 15.
B
A
D

Model # BBXL54NV
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 9 Factory No. 16434
Assembly Instructions for Table-top Console
11.Unscrew the four bolts and the washers to remove the Upper Spine from the Spine Assembly
(D), as shown above. So that you can use the table top console configuration,
NOTE: Keep the Upper Spine and the fasteners at a proper place in case you will use the
floating swivel mount.

Model # BBXL54NV
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 10 Factory No. 16434
Assembly Instructions for Table-top Console
12.Fasten the Top Shelf Frame (A) to the Lower Spine (D) by inserting one 2-1/2” Bolt (5) with
the Washers (6 and 7) through the drilled holes on the lower spine and securely screw into the
Flange Nut (8).
13.Plug the Spine End Cap (13) all the way onto the top of the Lower Spine (D).
2-1/2” Bolt
(1 used in this step) ⑤
Spine End Cap
(1 used in this step)
⑬
Lock Washer
(1 used in this step)
⑥
Flat Washer
(1 used in this step)
⑦
D
6
75
8
A
Flange Nut
(1 used in this step)
⑧