Whalen NOLAHBST User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-05-23 Rev. 0001-A Factory: GRWOVI
LOT NUMBER:
DATE PURCHASED: / /
Nolan Adjustable Height Swivel Barstool
Stock # NOLAHBST
Or
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]

2
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Seat with Backrest (Qty. 1) B- Base (Qty. 1)
C- Long Lower Leg (Qty. 4) D- Short Lower Leg (Qty. 4)
(Pre-attached)
(1) Ø1/4" x 1-3/8" Bolt (2) Lock Washer (3) Flat Washer
(Qty. 4+1 extra) (Qty. 4+1 extra) (Qty. 4+1 extra)
T-handle Allen Wrench Touch-up Pen
(Qty. 1) (Qty. 1)
Tools required: Allen wrench (provided).

3
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Position the Seat with Backrest (A) upside down on the carton or other protective support surface.
NOTE: Place a protective cover (like the bubble wrap packing material) over the carton or other support
surface to prevent from scratching.
3. Pick up the Base (B) and turn the upper plate of Swivel Plate 45 degree across the bottom plate.
4. Flip the Base (B) upside down and align the upper plate holes of the Swivel Plate with the threaded
inserts on the Seat Frame (A). Make sure that the top frame of the Base (B) aligned with Seat Frame (A)
properly.
5. Insert four 1-3/8” Bolts (1) with Lock Washers (2) and Flat Washers (3) through the swivel plate holes
and screw into the Seat Frame (A). Fasten all bolts with the Allen wrench.
6. Stand the stool upright.
Flat Washer
(4 used in this step)
③
Lock Washer
(4 used in this step)
②
Ø1/4" x 1-3/8" Bolt
(4 used in this step)
①

4
Assembly Instructions
7. The lower legs of this barstool are interchangeable for both bar height and counter height. The Long
Lower Legs (C) are pre-installed for shipping.
8. To adjust the seat height, you will need to unscrew the bottom bolts and washers on the square tubes on
the footrest to remove the Long Lower Legs (C). Then replace with the Short Lower Legs (D) and
tighten with the same bolts and washers.

5
INFORMATION FOR USE
1. This barstool is for indoor use only. Please use it only on smooth, even flooring.
2. The height of the seat is adjustable.
3. Please check that all bolts, screws and knobs are tight at least every 3 months or as needed.
4. If parts are missing, broken, damaged or wrong, please stop using this product until repairs are done by a
trained person.
 Do not stand or step on this stool.
 Do not sit on the front edge of the stool.
 Use for seating only, one person at a time.
 Use over smooth, level, seamless surfaces only.
 Do not use this stool unless all bolts, screws and knobs are firmly secured.
 Do not use stool as a stepladder.
 Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation.
 Use this stool for its intended purpose only.
 Use mild detergent only for cleaning.
 Failure to follow these warnings could result in serious injury.
Maximum load weight 136 kg (300 pounds).
A touch-up pen has been provided to repair any small nicks or scratches that may occur during assembly or
shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet
your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to
State.
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com
THIS UNIT IS INTENDED FOR USE ONLY WITHIN THE
MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE
MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING
POSSIBLE INJURY.

ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
Fecha 2016-05-23 Rev. 0001-A Fábrica: GRWOVI
LOTE NÚMERO:
FECHA DE COMPRA: / /
Taburete de altura ajustable Nolan
Serie # NOLAHBST
O
ENSAMBLE REQUERIDO POR ADULTO
Si tiene alguna pregunta relacionada con el ensamble o si faltan piezas, NO devuelva este producto al
establecimiento donde lo adquirió. Por favor llame a nuestro número de servicio al cliente y teniendo sus
instrucciones y lista de piezas lista para proporcionar el nombre del modelo, el nombre o el número de parte de
la fábrica:
866-942-5362
Hora estándar del Pacífico: 8:30 am - 4:30 pm, de Lunes - Viernes
O visite nuestro sitio web las 24 horas del día, 7 días a la semana para recibir asistencia del producto en
www.whalenstyle.com
O por correo electrónico su petición a [e-mail]

2
Lista de piezas y material de ferretería
Por favor, lea completamente todas las instrucciones y verifique que todas las piezas mencionadas y el
material están presentes antes de comenzar el ensamble.
A- Asiento con respaldo (Cant. 1) B- Base (Cant. 1)
C- Pata inferiore larga (Cant. 4) D- Pata inferiore corta (Cant. 4)
(Pre-ensanblada)
(1) Tornillo de Ø1/4" x 1-3/8" (2) Arandela de presión (3) Arandela plana
(Cant. 4+1 extra) (Cant. 4+1 extra) (Cant. 4+1 extra)
Llave Allen “T” Plumón de retoque
(Cant. 1) (Cant. 1)
Herramienta requerida: Llave Allen (proveida).

3
Instrucciones de ensamble
1. Desempacar la unidad y confirmar que se tiene todo el herraje y partes requeridas.
2. Ponga el asiento con respaldo (A) boca abajo sobre una superficie de apoyo.
NOTA: Coloque una tapa de protección (como el material de empaque de plástico de burbujas) en la
caja de cartón u otra superficie de soporte para evitar que se dañe.
3. Recoger la base (B) y girar el plato giratorio superior a 45 grados a través de la placa inferior.
4. Voltear la base (B) boca abajo y alinee los orificios de la placa superior de la placa giratoria con los
insertos roscados en el marco del asiento (A). Asegúrese de que el marco superior de la base (B)
alineado con el marco del asiento (A) adecuadamente.
5. Inserte cuatro tornillos de 1-3/8" (1) con las arandelas de presión (2) y arandelas planas (3) a través de
los orificios de la placa y fije en el marco del asiento (A). Fijar todos los tornillos con la llave Allen.
6. Colocar el taburete en posición vertical.
Arandela plana
(4 usados en este paso)
③
Arandela de presión
(4 usados en este paso)
②
Tornillo Ø1/4" x 1-3/8"
(4 usados en este paso)
①

4
Instrucciones de ensamble
7. Las patas inferiores de este taburete son intercambiables tanto para altura de la barra y la altura del
mostrador. Las patas inferiores largas (C) son pre-instaladas para el envío.
8. Para ajustar la altura del asiento, tendrá que desenroscar los tornillos inferiores y arandelas en los tubos
cuadrados en el descanso para eliminar las patas inferiores largas (C). A continuación, reemplace con la
patas cortas inferiores (D) y apriete con los mismos tornillos y arandelas.