Whalen ATD60H-13AX User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2018-07-24 Rev. 0001-A Factory: BESBEA
60" Audio Video Tower
Model # ATD60H-13AX
# ATD60H-13AXGR
CN Patent CN200920267469.6
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item
to the store where it was purchased. Please call our customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenfurniture.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: 60" Audio Video Tower
MODEL # ATD60H-13AX / ATD60H-13AXGR
MADE IN CHINA
1. Please read the Assembly Instructions prior to assembling this product.
2. Remove all hardware from the box and sort by size.
3. Check to see that all hardware and parts are present BEFORE assembling.
4. Ask a friend to assist you with the assembly of this furniture.
5. To avoid damage, assemble the product on a sturdy, level and protective surface.
6. Please wait until all steps are completed before fully tightening bolts.
7. Make sure all bolts are tightly fastened before the unit is used.
M AX I M U M R E C O M M E N D E D W E I G H T L O A D S
G E N E R AL I N F O R M A T I O N , T I P S
a n d
T R I C K S
This product is sold with one set of Tipping Restraint Hardware K
it. You must install the
Tipping Restraint Hardware between the wall and the tower
to prevent any accidents or
damages
. When properly installed, this restraint can provide protection against the unexpected
tipping of the unit due to small tremors, bumps or climbing. The restraint is only a deterrent
and is not a substitute for proper adult supervision. Use of tip-
over restraints may only reduce,
but not eliminate, the risk of tip
-
over.
THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 50 lb. (22.6 kg)
MAXIMUM LOAD 20 lb. (9.07 kg)

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware
are present before beginning assembly.
A- Left Leg and Spine Assembly (Qty. 1) B- Right Leg (Qty. 1)
C- Shelf Front Stretcher (Qty. 3) D- Top Panel (Qty. 1) E- Middle Fixed Shelf (Qty. 1)
F- Middle Upper/Lower Shelf (Qty. 2) G- Drawer Box (Qty. 1) H- Cable Wheel (Qty. 2)
(1) ¼-20 UNC-2A x 1/2 lg. Bolt (2) ¼-20 UNC-2A x 1 ¼ lg. Bolt (3) Shelf Pin
(Qty. 21+1 extra) (Qty. 14+1 extra) (Qty. 4+1 extra)
(4) Handle with Bolts (Qty. 1) (5) Metal Bracket (Qty. 2) 4 mm Hex Wrench (Qty. 2)
Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty. 1)
(Inside Plastic Bag)
Tools required: Hex wrench (provided) and Phillips screwdriver (not provided).

4
Assembly Instructions
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Hold the Left Leg and Spine Assembly (A) upright and simply swing the left leg outward. Align
and attach the side rails of Right Leg (B) to the back rails of Spine Assembly (A) with three
1/2” Bolts (1).
A
B
A
1
A
1/4” x 1/2” Bolt
(3 used in this step)
①

5
Assembly Instructions
3. Fit the U-shaped bracket on the three Front Stretchers (C) into the side rails of the leg
assemblies with six 1/2” Bolts (1).
1
C
C
C
B
A
C
A/B
C
A/B
1/4” x 1/2” Bolt
(6 used in this step)
①

6
Assembly Instructions
4. Locate the Drawer Box (G) on a scratch free surface as shown.
5. Pull the utility drawer all the way out, then simultaneously push the plastic release lever of the
ball bearing slide up on one side and down on the other side, and then pull the drawers
completely out.
6. Remove the bolts in the Handle (4), then use the bolts to attach the Handle to the outside of
the utility drawer.
G
4
4
Handle with Bolts
(1 used in this step)
④

7
Assembly Instructions
7. Turn the assembled tower frame at its back edge。
8. Fit the Drawer Box (G) between the legs and press firmly to the bottom metal frame. Fasten
the Drawer Box (G) in place with six 1-1/4” Bolts (2).
1/4” x 1-1/4” Bolt
(6 used in this step)
②
G
B
A
C
C
C
A/B
G
2
A/B
G
C
2
G
C
C
C
AB

8
Assembly Instructions
9. Fit the Top Panel (D) and Middle Fixed Shelf (E) onto the assembled shelf frames properly so
that the threaded inserts underneath shelf overlap the drilled holes on the Shelf Frames. Insert
four 1-1/4” Bolts (2) through the drilled holes and securely screw into each shelf.
D/E
A/C
2
D
C
E
A
B
C
1/4” x 1-1/4” Bolt
(8 used in this step)
②

9
Assembly Instructions
10. Fasten two Metal Brackets (5) to the Spine (A) at the desire height using four 1/2” Bolts (1).
Make sure that the right-angle side of Metal Bracket will face upward when the unit is turned
upright.
NOTE: The shelf holder location is adjustable. Choose the upper hole sets to increase the
lower shelf space.
1/4” x 1/2” Bolt
(4 used in this step)
①
Metal Bracket
(2 used in this step)
⑤
A
1
1
5
A
B
D
E
G

10
Assembly Instructions
11. Insert four Shelf Pins (3) into the proper hole sets on the inner side of legs. Be sure the Shelf
Pins and the installed Metal Brackets (5) are at the same level, so that they will hold the
Shelves (F) properly.
12. Rest the Shelves (F) onto the installed Shelf Pines (3) and Metal Brackets (5). Fasten the
Shelves (F) in place with two 1/2” Bolts (1) per bracket.
Shelf Pin
(4 used in this step)
③
1/4” x 1/2” Bolt
(4 used in this step)
①
F
F
F
A
1
1
5
A/B
3
B
D
E
G
A