WIN Enterprises PL-80720 User manual

Copyright © WIN Enterprises, Inc.
Dec
2014
Custom Embedded Solutions
Network Appliance
PL
PLPL
PL-
--
-80720
8072080720
80720
User Manual

Copyright © WIN Enterprises, Inc.
Dec
2014
© Copyright 2014. All Rights Reserved
Manual Edition 1.0, Aug., 2014
This document contains proprietary information protected by copyright. All rights are
reserved; no part of this manual may be reproduced, copied, translated or transmitted in
any form or by any means without prior written permission of the manufacturer.
The content of this document is intended to be accurate and reliable; the original
manufacturer assumes no responsibility for any inaccuracies that may be contained in
this manual. The original manufacturer reserves the right to make improvements to the
products described in this manual at any time without prior notice.
Trademarks
RTL is a trademark of Realtek
Microsoft, Windows, Windows NT are either trademarks or registered trademarks of
Microsoft Corporation
All other product names mentioned herein are used for identification purpose only and
may be trademarks and/or registered trademarks of their respective companies
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this document, the
manufacturer and distributor assume no liability resulting from errors or omissions in this
document, or from the use of the information contained herein.
For more information on PL-80720 or other WIN products, please visit our website
http://www.win-ent.com .
For technical support send your inquiries to
[e-mail].
Version 1.0

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 1. General Information.....................................4
1.1 Introduction.............................................................4
1.2 Specifications............................................................5
1.3 Ordering Information...............................................6
1.4 Packaging...............................................................6
1.5 Precautions ............................................................7
1.6 System Layout........................................................8
1.7 Board Dimensions ................................................10
Chapter 2. Connector/Jumper Configuration............. 11
2.1 Connector/Jumper Location and Definition........... 11
2.2 Connector and Jumper Setting .............................13
Chapter 3. System Setup.............................................21
Chapter 4. U-Boot Reference Manual .........................23
4.1 The boot process..................................................23
4.2 Built-in commands................................................24
4.3 Information commands .........................................27
4.4 MII commands......................................................27
4.5 Network commands..............................................28
4.6 USB commands ...................................................29
4.7 Memory commands ..............................................30
4.8 Serial port commands...........................................31
4.9 Environment variables commands........................31
4.10 I2C commands ...................................................32
4.11 Environment variables ........................................33
4.12 Boot commands .................................................37
4.13 Automatic booting...............................................38
4.14 Firmware update commands ..............................39
4.15 other important commands .................................41
Appendix A: Cable Development Kit ..........................42
Contents

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 1. General Infor ation
4
Chapter 1. General Information
1.1 Introduction
The PL-80720 is a desktop hardware platform designed for network
service applications. It is suitable for SOHO (Small Office, Home Office),
SMB (Small Medium Business), and ROBO (Remote Office, Branch Office)
segments. The PL-80720 supports the Cavium® OCTEON III CN7010
family of processors and supports onboard DDR3L memory up to 4GB.
In order to provide the best network performance and utilization, the
standard device comes equipped with onboard eMMC flash for boot
device and has a place reserved for an optional slim-type one 2.5" SATA
HDD. PL-80720 supports 5 Copper GbE ports on rear-panel. For easy
access, the front panel also has two USB 2.0 port, one RJ-45 console port
and LED indicators that monitor power and storage device activities for
local system management, maintenance and diagnostics. In addition, the
PL-80720 supports one mini-PCIe slot. It is RoHS, FCC and CE
compliant.

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 1. General Infor ation
5
1.2 Specifications
Processor System
Caviu OCTEON III CN7010 fa ily
CPU
processor, up to 1.0GHz.
Chipset Caviu OCTEON III CN7010 SOC
BIOS U-Boot
Memory
Onboard 36bit DDR3L 1066MHz Me ory.
Technology
ECC Support
Capacity Up to 4 GB onboard
Expansion
Expansion Slots One ini-PCIe socket.
Ethernet
Five RJ45 GbE ports, RTL8211E and
GbE Ethernet
RTL8214B via RGMII and QSGMII
SATA HDD One internal 2.5” SATA HDD bay (Option)
Storage
eMMC On-board 4GB eMMC Flash, up to 8GB
I/O
Two external USB2.0
USB
one internal 5x2 pin header
one RJ45 Console port (COM1)
Serial
one internal 5x2 pin header (COM2)
GPIO 4 x GPO pin header
Power Supply
Watt 40W AT power adaptor supply
Mechanical and
Environmental
For Factor Desktop
1 x Power LED, (Green)
1 x Syste LED, (Green, Yellow)
LED
1 x HDD LED, (Green)
1 x USB LED, (Green)
Di ensions （ W x D x H ）
232 (W) x 152 (D) x 44 (H)
Operating Te perature Operating: 0 ~ 40°C ( 32 ~ 104°F )
Storage Te perature -20 ~ 75°C (-4 ~ 167°F)
10 ~ 85% relative hu idity, non-operating,
Hu idity
non-condensing
Certifications CE/FCC

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 1. General Infor ation
6
1.3 Ordering Information
We provide some accessories for PL-80720 appliance.
PL-8072A
Desktop Caviu OCTEON III CN7010 Network Syste ,
5 Copper GbE, eMMC, SATA, Mini-PCIe
DK001
Cable develop ent kit
CB-CO5204-00 Cross over cable
CB-EC5200-00 Ethernet cable
CB-RJDB91-00 RJ45 Console cable
1.4 Packaging
Make sure that the following items have been included in the package
before installation:
1. PL-80720 Appliance
2. Quick Installation Guide (Optional)
3. Cables (Optional)
If any item of above is missing or damaged, please contact your dealer or
retailer from whom you purchased the PL-80720. Keep the box and
carton for possible near-term shipment or storage of the PL-80720.
After you unpack the goods, inspect and make sure the packaging is intact.
Do not connect the power adapter to the PL-80720 if it appears damaged.
Note: Keep the PL-80720 in the original packaging until you start installation.

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 1. General Infor ation
7
1.5 Precautions
Please make sure you properly ground yourself before handling the PL-
80720 appliance or other system components. Electrostatic discharge
can be easily damage the PL-80720 appliance.
Do not remove the anti-static packing until you are ready to install the
PL-80720 appliance.
Ground yourself before removing any system component from its
protective anti-static packaging. To ground yourself grasp the expansion
slot covers or other unpainted parts of the computer chassis.
Handle the PL-80720 appliance by its edges and avoid touching the
components on it.
There is a risk of explosion if battery is replaced by incorrect type.
Dispose of used batteries according to the instructions.
CAUTION

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 1. General Infor ation
8
1.6 System Layout
PL
-
0720
Rear
Side
Layout
PL
-
0720
Front
Side
Layout

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 1. General Infor ation
9
PL
-
0720
Internal
Layout

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 1. General Infor ation
10
1.7 Board Dimensions

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 2. Connector/Ju per Configuration
11
Chapter 2. Connector/Jumper Configuration
2.1 Connector/Jumper Locations and Definitions

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 2. Connector/Ju per Configuration
12
Connector List
Connector Description Connector Description
CN1
System
FAN Connector CN18 POWER ACK (+12V Only)
CN2
System
FAN Connector CN19 POWER SWITCH
CN3
T
AG Pin Header ( Debug only) P1 WATCH DOG Select
CN4
COM2
BOX Header P2
PCIE
GEN1/GEN2 Select
CN5
GPIO
Pin Header
P3
B
YPASS Select
CN6
MCU
Programming Pin Header
D1
USB
LED
(
Debug only)
CN7
S
ATA Power Connector
D2
SYSTEM
LED
CN8
MINIPCIE
Connector
D3
B
YPASS LED
CN9
MINIPCIE
Connector
D4
POWER
LED
CN10
S
ATA Connector
D5
HDD
LED
CN11
WLAN
LED 1x2 Wafer (from CN9) D6~D14
LAN
LED
CN12
WLAN
LED 1x2 Wafer (from CN8)
LED8
Front
panel LED : (From top to
CN13
3.96mm
1x2 POWER (+12V Only) bottom)
CN14
Console
& USB Connector (POWER LED , HDD LED ,
CN15
R 45
LAN SYSTEM LED , USB LED ,
CN16
R 45
LAN PORT (1X4) BYPASS LED)
CN17
R 45
LAN PORT (1X4)
MB-80720 Connectors & Jumpers

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 2. Connector/Ju per Configuration
13
2.2 Connector and Jumper Settings
CN1: System FAN connector
Pin Define
1Ground
2+12V
3N/A
CN2: System FAN connector
Pin Define
1Ground
2+12V
3N/A
CN4: COM2 BOX Header
Pin Define Pin Define
1N/A 2SIN
3SOUT 4N/A
5GND 6N/A
7RTS 8CTS
9N/A 10 N/A

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 2. Connector/Ju per Configuration
14
CN5: GPIO Pin Header
Pin Define Pin Define
1GPIO16 2GP16+
3GPIO17 4GP17+
5GPIO18 6GP18+
7GPIO19 8GP19+
9GND 10 +3.3V
CN7: SATA PWR
Pin Define
1+12V
2GND
3GND
4+5V

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 2. Connector/Ju per Configuration
15
CN8/9: MINI-PCIE
Pin Define Pin Define
1WAKE# 23.3V
3Reserved 4GND
5Reserved 6
1.5V
7
CLKREQ# 8 Reserved
9
GND 10 Reserved
11
REFCLK- 12 Reserved
13
REFCLK+ 14 Reserved
15
GND 16 Reserved
17
Reserved 18 GND
19
Reserved 20 Reserved
21
GND 22 PERST#
23
PERN0 24 +3.3VAUX
25
PERP0 26 GND
27
GND 28 +1.5V
29
GND 30 SMB_CLK
31
PETN0 32 SMB_DATA
33
PETP0 34 GND
35
GND 36 USB_D-
37
Reserved 38 USB_D+
39
Reserved 40 GND
41
Reserved 42 LED_WWAN#
43
Reserved 44 LED_WLAN#
45
Reserved 46 LED_WPAN#
47
Reserved 48 +1.5V
49
Reserved 50 GND
51
Reserved 52 +3.3V

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 2. Connector/Ju per Configuration
16
CN10: SATA Connector
Pin Signal
1Ground
2TXP
3TXN
4Ground
5RXN
6RXP
7Ground
CN11: WLAN LED 1x2 Wafer
Pin Signal
1VDD3P3V
2LED1 WLAN
CN12: WLAN LED 1x2 Wafer
Pin Signal
1VDD3P3V
2LED2 WLAN

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 2. Connector/Ju per Configuration
17
CN13: 3.96mm 1x2 POWER (+12V Only)
Pin
Define
Pin
Define
1GND 2+12V
CN14 ：
：：
： Console & USB Connector
USB
Pin Define
1+5V
2DATA0-
3DATA0+
4GND
5+5V
6DATA1-
7DATA1+
8GND
RJ45
Pin Define
9RTS#
10 N/A
11 SOUT
12 GND
13 GND
14 SIN
15 N/A
16 CTS#

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 2. Connector/Ju per Configuration
18
CN15: LAN RJ-45 Connector
Pin Define
1TX+
2TX-
3RX+
4Chassis Ground
5Chassis Ground
6RX-
7Chassis Ground
8Chassis Ground
D1: Speed indicated LED
1 Gbps GREEN
100 Mbps YELLOW
D2 :Link/Activity LED
Link GREEN
Activity BLINKING

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 2. Connector/Ju per Configuration
19
CN18: DC +12V Power Jack (2Pin)
Pin Define Pin Define
1+12V 2GND
CN19: POWER SWITCH
Pin Signal
1GND
2+12V

Copyright © 2015 WIN Enterprises, Inc.
Dec.,
2014
Chapter 2. Connector/Ju per Configuration
20
JP1: WATCH DOG Select
Pin
Setting
Open
Close
NON WDT
WDT
JP2: PCIE GEN1/GEN2 Select
Pin
Setting
1-2 GEN2
2-3 GEN1
JP3: BYPASS Select
Pin
Setting
1-2
BYPASS
Enabled
2-3
BYPASS
Disabled
Jumper Setting