Winco 3170B User manual

Page 1 of 4
006250 Rev. T 04/23/20 NCG
1. READ AND FOLLOW ALL DIRECTIONS.
2. NEVER place screen on a cart, table, stand or other objects; Screen could fall and INJURY MAY OCCUR.
3. NEVER place screen near open flame or over a radiator or heat register.
4. NEVER place screen in front of a door or exit sign; or during emergency screen could hinder evacuation.
5. SUFFOCATION DANGER to children if vinyl is not attached to screen; Screen could block nose and mouth
and prevent breathing. VINYL SCREEN IS NOT A TOY.
6. DO NOT allow children to play with screen. Screen could fall and INJURY MAY OCCUR.
7. Screen should ALWAYS be positioned on level surface.
8. NEVER stand or ride on screen legs; INJURY MAY OCCUR.
9. DO NOT use screen in or with ANY type of vehicle or trailer.
10. DO NOT attach objects to screen frame. Screen can tip over and INJURY MAY OCCUR.
11. Any screen with broken or missing parts, torn vinyl, or other visible damage should be removed from service
immediately.
12. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
13. SAVE THESE INSTRUCTIONS for future reference and training.
14. Both small and large magnets can pose dangers to kids and adults. Mishandling of magnets may
cause injury or property damages. Make sure to keep magnets away from people who are wearing
pacemakers or other medical devices. Also keep magnets away from CRT monitors, CRT TVs, and
other electronic devices.
Screen Model: 3170B
Designer Three Panel Screen
Tools needed:
•Scissors or Box Cutter
•5/32 Allen Wrench (provided)
•Phillips Screwdriver
1. After checking your product for any shipping damage, remove all packing material and hardware that was secured for
shipping. Cut tape and/or plastic with scissors using caution to prevent damage to the screen.
LEG INSTALLATION (SEE PHOTOS ON NEXT PAGE)
2. Using a Phillips Screwdriver, Install (2) Screen Leg Reinforcement Tubes (#5) between Leg Frame Assemblies (#3)
using 4-Phillips Head Screws (5A), one on each end, through (#3) into (#5).Leave screws on one Leg Frame
Assemblies (#3) loose to allow assembly to be inserted into Wing/Mid Frame Assembly (#1A).
3. Insert both Leg Frame Assemblies (#3) into the bottom of the Wing/Mid Frame Assembly (#1A).
Line up the holes in (#3) w/ the holes in (#1A).
4. Using the Allen Wrench provided screw in 1-Button Socket Screw (3D), per leg, through (#1A) and into (#3). Tighten 2-
Phillips Head Screws (5A) that were left loose in step 2.
PANEL REPLACEMENT (SEE PHOTOS ON NEXT PAGE)
5. To replace Vinyl Panels (#4), hold the screen by the top Screen Rod (#2A).
6. Next, using the Allen Wrench provided, push in on the small hole just below the Snap Button (#2B).
Re-install (#2A) by repeating the above procedure, then release (#2B) when (#2A) is in place.
CARE AND MAINTENANCE OF YOUR SCREEN
7. Periodically check all fasteners for tightness.
8. To clean Vinyl Panels use only mild liquid soap and water.
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY.
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
If you have trouble understanding these instructions, contact Winco Customer Service at [phone] or
e-mail: [e-mail], before attempting to use this product; otherwise injury may occur.
Winco assumes no responsibility for damage or injury caused by the
improper assembly, installation, or use of these products.

Page 2 of 4
006250 Rev. T 04/23/20 NCG
Wrinkles in Vinyl – Storage and/or shipping causes wrinkles in the vinyl screen. This is normal. Please allow 1-2 weeks at
room temperature (approx. 70+ degrees) to allow for vinyl to return to original appearance.
Items Included with Screen: Qty.
(1A) Wing/Mid Frame Assembly Kit 1
(1B) Domed Plastic Insert 10
(2B) Snap Buttons 4
(2A) Screen Rod 6
(2B) Snap Buttons 12
(3) Leg Frame Assembly 2
(3B) 2” Caster 4
(3C) Caster Insert 4
(3D) ¾” Button Socket Screw 2
(4) 3170 Vinyl Panel 3
(5) Screen Leg Reinforcement Tube 2
(5A) 2” Phillips Head Screw 4
(6) MAGNET,1/2" X 1/8" 2
Visit our website at Wincomfg.com for a complete parts list catalog of your chair or
call Customer Service at 1-800-237-3377 to request it by mail.

Page 3 of 4
006250 Rev. T 04/23/20 NCG
GENERAL CARE AND CLEANING:
Periodically inspect tightness of all screws, bolts, and nuts. Winco furnishings are built to provide durable, reliable
service when properly cared for. In general, all of our products should be cleaned, rinsed, and allowed to air dry. It
is important to note that disinfecting a product is not the same as cleaning the product. Disinfectants alone will not
provide adequate cleaning. They do not have grease or oil cutting properties to remove grime or hair and skin oils.
Over time, the appearance, feel, and performance of your upholstery may diminish if not cleaned properly.
CLEANING:
To remove grime or hair and body oils, your furnishings should be cleaned with a mild soap and water solution and
a damp cloth on a regular basis. Avoid harsh detergents that could damage the finish of your product. If the
furnishing is disinfected with bleach, it MUST be wiped off using only clean water on a damp cloth and then be
allowed to air dry. Failure to rinse with clean water can result in a build-up of residues over time that can damage
your product.
Magnet Disclaimer
Disclaimer – It is required that the buyer read and understand these instructions
before using the magnet.
Both small and large magnets can pose dangers to kids and adults. Mishandling of
magnets may cause injury or property damages. Make sure to keep magnets away
from people who are wearing pacemakers or other medical devices. Also keep
magnets away from CRT monitors, CRT TVs, and other electronic devices.

Page 4 of 4
006250 Rev. T 04/23/20 NCG
Design, appearance, parts, and construction are subject to change without notice.