Winco Vero Care Cliner Operation manual

VERŌ CARE CLINER
OWNERS OPERATING AND MAINTENANCE MANUAL
IMPORTANT - DO NOT DISCARD THIS MANUAL.
KEEP THIS MANUAL FOR FUTURE REFERENCE AND TRAINING.
Copyright © 2020 Winco Mfg., LLC

Page 2 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
Do NOT install, maintain, or operate this equipment without reading and following
this manual, otherwise injury and/or damage may result.
IF YOU HAVE ANY QUESTIONS OR CONCERNS,
PLEASE CONTACT WINCO MFG., LLC.
Winco assumes no responsibility for damage or injury caused by improper assembly,
installation, use, or maintenance of these products.
No part of this manual may be duplicated in any form without the prior consent of
Winco Mfg., LLC. Unauthorized duplication and/or distribution of these materials
may result in civil prosecution to the maximum extent allowed by law.
The information contained in this manual is subject to change without notice.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
These instructions are available online.
Visit wincomfg.com to download.
PRODUCTS WITH THE FOLLOWING MARKINGS ARE INTENDED FOR COMMERCIAL USE ONLY:

SYMBOLS
TYPE B APPLIED PART
FOLLOW INSTRUCTIONS DC VOLTAGE
GENERAL WARNING
SYMBOL FOR MANUFACTURER
TRENDELENBURG
PINCH-POINT WARNING
Page 3 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC

Page 4 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
TABLE OF CONTENTS
INTENDED USE STATEMENT............................................................................................................................................................................................................ 5
TRANSPORTATION, STORAGE, HANDLING & DISPOSAL........................................................................................................................................................ 5
PREPARATION: BEFORE YOU BEGIN ............................................................................................................................................................................................ 5
IMPORTANT SAFETY INFORMATION............................................................................................................................................................................................. 6
FOR CHAIRS WITH POWERED OPTIONS (POWERED RECLINER WITH HEAT AND MASSAGE, ETC.)................................................................... 7
ISOLATION DIAGRAM FOR HEAT & MASSAGE OPTION.................................................................................................................................................... 8
SCHEMATIC DIAGRAM FOR POWER RECLINER OPTION................................................................................................................................................. 9
FOR ALL CONFIGURATIONS (HEAT AND MASSAGE, ETC.).............................................................................................................................................. 10
ASSEMBLY INSTRUCTIONS............................................................................................................................................................................................................. 11
BACK ASSEMBLY........................................................................................................................................................................................................................ 11
ARMREST COVER INSTALLATION (OPTIONAL ACCESSORY).......................................................................................................................................... 13
OPERATING INSTRUCTIONS: ATTENDANT.................................................................................................................................................................................. 15
CASTER OPERATION: LOCK / UNLOCK ................................................................................................................................................................................ 15
FOOT PLATE OPERATION (OPTIONAL FEATURE)................................................................................................................................................................ 16
RECLINE CHAIR (ATTENDANT POSITION)............................................................................................................................................................................ 17
RECLINING CHAIR (ATTENDANT POSITION, POWER RECLINER).................................................................................................................................. 18
RETURN CHAIR TO UPRIGHT POSITION (ATTENDANT POSITION)............................................................................................................................... 19
RETURN CHAIR TO UPRIGHT POSITION (ATTENDANT POSITION, POWER RECLINER).......................................................................................... 20
ACTIVATING TRENDELENBURG POSITION (ATTENDANT ONLY).................................................................................................................................... 21
TRENDELENBURG TO RECLINE (ATTENDANT ONLY)......................................................................................................................................................... 21
ACTIVATING TRENDELENBURG POSITION (ATTENDANT ONLY, POWER RECLINER)................................................................................................ 22
SWING-ARM OPERATION (ATTENDANT ONLY) .................................................................................................................................................................. 23
TRANSFERRING PATIENT TO CHAIR (SWING-ARM ONLY).............................................................................................................................................. 24
SIDE TABLE OPERATION (OPTIONAL FEATURE)................................................................................................................................................................. 25
PIVOT TABLE OPERATION (OPTIONAL FEATURE).............................................................................................................................................................. 26
OPERATING INSTRUCTIONS: OCCUPANT................................................................................................................................................................................... 27
RECLINE WHILE IN THE SEATED POSITION (POWER RECLINER MODELS ONLY)...................................................................................................... 28
RETURNING TO SEATED POSITION (NON-POWER RECLINER MODELS ONLY).......................................................................................................... 29
RETURNING TO SEATED POSITION (POWER RECLINER MODELS ONLY) ................................................................................................................... 30
HEAT / HEAT & MASSAGE OPERATION (OPTIONAL FEATURE)...................................................................................................................................... 31
GENERAL MAINTENANCE................................................................................................................................................................................................................. 33
GAS CYLINDER OPERATION.................................................................................................................................................................................................... 33
GENERAL CARE & CLEANING......................................................................................................................................................................................................... 34
OPTIONAL BATTERY.......................................................................................................................................................................................................................... 35
SPECIFICATIONS (NON-POWER MODELS).................................................................................................................................................................................. 36
SPECIFICATIONS (POWER RECLINER MODELS)........................................................................................................................................................................ 37
VERŌ CARE CLINER OPTIONS......................................................................................................................................................................................................... 38
WARRANTY INFORMATION............................................................................................................................................................................................................. 39

Page 5 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
INTENDED USE STATEMENT
The Verō Care Cliner is a recliner for use in medical settings. It is designed to provide comfort for patients seated
for extended periods of time while receiving clinical treatments such as Dialysis or Infusion or during recovery from
surgical procedures where positional adjustments are beneficial. The recliner is also suitable for general use in
many medical settings such as, but not limited to, hospital room chair, waiting room chair, convalescent home chair,
etc.
TRANSPORTATION, STORAGE, HANDLING AND DISPOSAL
• The product should be transported in factory packaging, inside an appropriate medium for the destination,
i.e. truck, air, or sea cargo containers.
• The product should be stored in a dry environment that will inhibit rust or mold formation.
• Winco Mfg., LLC recommends not leaving the product in the factory packaging in excess of three (3)
months.
• The product should always be handled in a manner consistent with the user instructions and in a manner to
prevent contamination after each use.
• The product has many recyclable components and to the extent practical, all eort should be used to
recycle responsibly. Otherwise, the product components shall be disposed of in accordance with local
statutes.
PREPARATION: BEFORE YOU BEGIN
1. You should thoroughly read and possess a full understanding of this manual before using this product. It is
imperative that all users know how to properly operate all functions and features of this product, including,
but not limited to, footplate, casters, swing arms and side table operation and any accessories including Heat,
Heat & Massage, and Power Recline.
2. Carefully examine your product for any damage. Be sure to inspect all components. IF DAMAGE IS EVIDENT,
CONTACT FREIGHT CARRIER OR WINCO IMMEDIATELY.
3. Remove all packaging material and any hardware that was secured for shipping. Save packaging (see #6
below)
4. Carefully remove all components and any included tools and/or parts from the carton.
5. You may need to cut packaging materials with a box cutter or scissors to access the product. Use CAUTION
to avoid personal injury or damage to the product.
6. Save all boxes and packaging material until AFTER you have assembled your product and have verified that
all components are functioning properly. These material are required if it becomes necessary to return the
product.
7. Read all hangtags and labels carefully. Hangtags and labels contain pertinent information regarding your
product specifically. They may be located on the back of the chair, attached to the handles or chair back.
8. DO NOT install, maintain, or operate this equipment without reading and following this manual otherwise injury
and/or damage may result. In the event that someone improperly operates this product and causes damage
to it, the warranty may be voided. IF YOU HAVE QUESTIONS OR CONCERNS PLEASE CONTACT WINCO
MFG., LLC.
WINCO ASSUMES NO RESPONSIBILITY FOR DAMAGE OR INJURY CAUSED BY IMPROPER ASSEMBLY,
INSTALLATION, USE, MODIFICATION, OR IMPROPER MAINTENANCE OF THESE PRODUCTS.

Page 6 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
IMPORTANT SAFETY INFORMATION
FOR CHAIRS WITH POWERED OPTIONS (HEAT, MASSAGE, POWER RECLINER, ETC.)
When using an electrical appliance, basic precautions should always be followed, including the following:
To reduce the risk of electric shock always unplug this product from the electrical outlet and disconnect
the battery (if equipped) before reaching inside, cleaning, maintenance or servicing. Do not operate the
chair unless all four wheels or pedestal feet are resting on the floor.
1. Unplug this product from the electrical outlet when not in use.
2. Supervision should be provided when using this product.
3. Use this product only for its intended use as described in this manual.
4. DO NOT use attachments not recommended by the manufacturer.
5. Never operate this product and remove from service if it has a damaged cord or plug, if it is not working properly, if it has
been dropped or damaged, or dropped into water, contact an authorized Winco service center for instructions.
6. DO NOT carry or pull this product by power supply cord or use the cord as a handle.
7. Keep the cord away from heated surfaces.
8. DO NOT use outdoors.
9. To disconnect, position all controls to the "off" position, then remove the plug from the outlet. Pull the molded plug end
only to remove the cord; never pull on the cord only.
10. Clean the switch with a damp cloth only. Warranty will be VOID if liquid is introduced into the switch mechanism(s) or any
electrical components.
11. Extension cords are not recommended.
12. DO NOT roll recliner or other equipment over the cord and always keep the cord stored properly (see "Cord Storage" on
page 32). Proper cord storage is essential in order to prevent damage. Should any cord or any electrical components have
any signs of damage, they should be immediately replaced to avoid the possibility of liquid penetration or exposure to
current, which can cause further damage to other components, caregivers, or patients.
13. This product is shipped with a 3 pin cord set for North America on a nominal 120 VAC circuit. The product will operate on
circuits from 120-240 VAC with a local country power cord equipped with an IEC plug into the controller. If the plug does not
fit into the outlet, contact a certified electrician to install the proper outlet. DO NOT MODIFY THE PLUG IN ANY WAY. No
adapter should be used with this product.
14. For an added level of safety; Winco recommends the use of a 120 volt GFCI (ground fault circuit interrupter) outlet.
15. Never insert pins or attach other metallic fasteners into or onto any part of this chair.
16. DO NOT use this product if the covering shows signs of deterioration, such as checking, blistering, or cracking.
17. KEEP DRY. DO NOT operate in a wet or moist condition or environment.
Long term, continuous exposure to heat may cause burns. It is recommended that skin in contact
with heated area be checked for redness and blistering during long term usage.DO NOT use on
an infant or incapacitated person. DO NOT use on insensitive skin or on a person with poor blood
circulation. If you are uncertain if you should use this product, please consult your physician about
the use of heat and massage.
DO NOT crush or pinch heating elements or wiring.
*IMPORTANT SAFETY INFORMATION CONTINUED ON THE NEXT PAGE*

Page 7 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
IMPORTANT SAFETY INFORMATION (CONTINUED)
FOR CHAIRS WITH POWERED OPTIONS (HEAT, MASSAGE, POWER RECLINER, ETC.)
ADDITIONAL INFORMATION FOR VERO CARE CLINER PRC (POWER RECLINER CHAIR) ONLY:
1. The Vero Care Cliner PRC (Power Recliner Chair) uses a linear actuator to drive the recline mechanism inside
the chair. The actuator is controlled with a switch panel on the outside of the right hand arm or optionally both
arms. A handset can be ordered for convenience of the attendant.
2. The Handset or switch panel should ONLY be used to position the chair recline angle; unless using the
Trendelenburg feature, which may be performed manually. Trendelenburg does not require use of the handset
switch panel. The Vero Care Cliner PRC may be positioned from full upright to full recline position using the
handset or switch panel.
3. NEVER attempt to close the leg rest manually on a Power Chair. The recline motion is controlled by the handset
or switch panel; therefore, forcing the chair into a dierent recline angle will damage the chair and void the
warranty.
4. The Vero Care Cliner PRC includes an "AC to DC" switching power supply, operating from a standard AC power
outlet (120 VAC/60 Hertz nominal) and a supplemental rechargeable battery (optional). This power supply
allows operation world wide on voltages from 100-240 VAC and frequencies from 50-60 HZ with the proper
power cord.
5. The (optional) rechargeable battery is a back up system to be used for power outages. Allowing the battery to
diminish lower than 30% (see page 35 "Battery Status Indicator") can cause permanent damage to the battery,
resulting in the battery no longer being able to hold a full charge. This will void the warranty on the battery.
6. To fully charge the (optional) rechargeable battery for the first time, the Vero Care Cliner PRC must be plugged
in for 10 hours. Uncoil the power cable from the back of the Power Reclining Chair and plug it into a properly
grounded outlet. Plugging in the Vero Care Cliner PRC initiates the battery to charge. Please refer to the
"Power Requirements" on page 9 for further information.
7. Removal of power cord does not stop power function if battery option is present and battery is charged.
8. Always completely deactivate the battery before servicing, transporting, or shipping. Refer to pg. 35 for
instructions.
9. Should the battery enclosure be damaged, deformed, or have any sign of leakage, the chair and battery should
be taken out of service immediately. Batteries should be disposed of appropriately. Contact your municipal
hazardous waste center for instructions. Always handle leaking batteries with gloves.

IMPORTANT: PLEASE READ
For Heat & Heat and Massage Option:
This equipment is marked with the industry recognized symbol indicating it is a “Class II
Double-Insulated” device as defined by IEC 60601-1. As such, it does NOT require a three
conductor power cord (i.e. one with a ground connection) for safety purposes. While the
equipment can be safely operated with no ground connection, a three conductor power
cord is provided to satisfy customer expectations for typical equipment configuration.
Devices qualifying as double insulated require dierent testing and examination procedures than “Class
I Grounded” devices. If your facility requires the product to be tested, be sure to follow testing and
examination procedures for “Class II Double-Insulated” devices.
ISOLATION DIAGRAM FOR HEAT & MASSAGE SYSTEM
A I T
A Basic Operational
B Double Insulated / Reinforced
C Double Insulated / Reinforced
D Double Insulated / Reinforced
E Double Insulated / Reinforced
F Double Insulated / Reinforced
G Inlet FE Pin only connects to inlet & pad
Page 8 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC

IMPORTANT: PLEASE READ
For Vero Care Cliner PRC (Power Recliner Chair) Option: Schematic Diagram
Page 9 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC

IMPORTANT: PLEASE READ
FOR ALL CONFIGURATIONS (WITH OR WITHOUT HEAT, MASSAGE, ETC.)
DO NOT LIFT OR CHANGE CHAIR RECLINE ANGLE BY USING THE LEG REST. THIS
COULD CAUSE INJURY TO THE USER OR DAMAGE TO THE RECLINE MECHANISM
AND WILL VOID THE WARRANTY.
1. READ AND FOLLOW ALL DIRECTIONS.
2. This is a clinical medical recliner. It is used to position an occupant comfortably while receiving various
treatment regimens. Care should always be taken to assess an occupants medical condition PRIOR to use of
recliner and PRIOR to positioning occupant to determine if this reclining chair is medically appropriate for the
occupant's use.
3. Keep all extremeties clear of the recliner mechanisms when operating the chair with an occupant. Exercise
caution while attending to the occupant of the chair. They have the ability to change the position of the chair
unexpectedly, which can cause injury.
4. Keep children away from the extended foot support mechanism, from behind the chair, or near any moving
parts.
5. DO NOT use the recliner if the Trendelenburg Damper and/or Gas Spring is removed or damaged.
6. DO NOT put hands, feet or clothing into any openings when changing positions on recliner. Attendant MUST
confirm that users arms, legs, hands and feet are safe while changing recliner angle or SERIOUS INJURY
MAY RESULT.
7. Remove or move chair accessories (i.e. side table, pivot table, etc.) out of the way of occupant's legs when
reclining the occupant.
8. LOCK casters at all times when the chair is stationary AND when an occupant is in the chair. UNLOCK casters
ONLY when moving the chair for any reason.
9. DO NOT use recliner for transporting occupant in a vehicle or trailer. Winco recliners have not been tested or
approved for use by an occupant in a vehicle or trailer.
10. DO NOT use chairs to transport patients unless properly configured with a footplate, push handle, gas back,
or power recline option.
11. NEVER sit on the chair arms, backrest, or legrest; SERIOUS INJURY to user may occur. The chair may be
damaged.
12. Periodically check the tightness of all nuts, bolts, and screws at least once every year.
13. Any recliner with broken recline mechanisms, torn upholstery, or other mechanical or visible damage should
be immediately removed from service until repaired.
14. NEVER EXCEED the recommended weight capacity. Overloading a chair may cause serious damage to user.
The chair may be damaged. Overloading the chair voids the warranty.
15. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS FOR
REPAIRS TO THE CHAIR.
16. Chairs are suitable for indoor use only. Keep this product in a dry
environment. Never operate the chair in wet conditions.
USE CAUTION WHEN CLEANING NEAR
MECHANISMS. KEEP FINGERS, HANDS,
AND ALL OTHER BODY PARTS AWAY
FROM MOVING PARTS THAT CAN CAUSE
SERIOUS INJURY.
Page 10 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC

Page 11 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
BACK ASSEMBLY
1. Lock ALL four (4) casters on chair base with your foot
(See "Lock / Unlock Casters").
Keep objects and persons clear of the
chair before performing step 2.
2. Recline mechanism should be in the upright position.
Remove any packaging on the mechanism.
3. Pull up the apron and rear cover on the lower rear
of the back, exposing the mounting brackets (A). Lift
the upholstered back by its sides while aligning the
mounting brackets with the recline mechanism (B).
Keep hands clear of connection
points or injury may occur.
• It is recommended that two (2) people
be used to complete Step 3-A and 3-B.
• Be careful not to tear or puncture vinyl.
ASSEMBLY INSTRUCTIONS
1
23
"BACK ASSEMBLY" CONTINUED ON THE NEXT PAGE.

Page 12 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
BACK ASSEMBLY - CONTINUED
4. Slide the back onto the recline mechanism
until the middle hole of the mounting bracket
A is aligned with the middle hole of the recline
mechanism arm B (4).
It is recommended that two people
be used for this step.
5. Install knob A (tethered to back) and tighten
securely (5).
Test the back installation by pulling up
on the back. The back should remain
securely in place. If the back is loose,
check that bracket A has captured
arm B and that knob is securely
tightened in place (5).
4
5

1. Raise the side table by grasping the center of the table and gently lift into place.
2. Locate large square opening in cover and position over the side table. Gently stretch the opening
over the side table and slide over side table.
3. Fit the front portion of the armrest cover over the front of the arm. Pull down tight for best fit.
4. Fit the rear portion of the armrest cover over the rear of the arm.
5. For the premium table, you will need to release the table slightly to allow space to tuck the apron
into the gap. The standard table will have enough room in the upright position.
6. Pull the apron through the gap at the back of the side table completely (premium side table
pictured). Smooth out wrinkles.
Page 13 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
ARMREST COVER INSTALLATION (OPTIONAL ACCESSORY)
CHAIRS WITH SIDE TABLES
12
3
456
NOTE: Cover designs vary based on chair options (i.e. tables, heat/massage, etc).
NOTE: Install right hand cover over right arm and left hand cover over left arm.

1. Remove the adjustment knob and the pivot table completely. You MUST remove the knob.
2. Pull the arm rest cover down over the chair arm. Ensure the pivot table bracket is inserted through
the hole in the arm rest cover.
3. Reinstall the pivot table and adjustment knob.
Page 14 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
CHAIRS WITH PIVOT TABLES
ARMREST COVER INSTALLATION - CONTINUED
1
NOTE: Install right hand cover over right arm and left hand cover over left arm.
2
1
3

There are multiple caster and foot types available for this recliner, including, 5" casters with foot plate (rigid, total-
lock), 3" casters without foot plate (wheel-lock), and pedestal feet. Total-lock casters lock the wheel and swivel
mechanism when pressing down on the tab.
The front two (2) casters are rigid casters. They are NOT designed to swivel in order
to facilitate stable straight steering. In addition, the front locking tabs are always
accessible. When the locking tabs are locked down, caster wheels will NOT roll.
The rear two (2) casters are total-lock casters. They are designed to swivel 360°.
When locking tab is locked down, caster wheels will NOT roll and caster will NOT
swivel.
1. TO LOCK CASTER: Press down on the wheel tab (A) with the sole of your shoe.
Tab will lock wheel into position shown.
2. TO UNLOCK CASTER: Press down on the TOP of the wheel tab (B) with the
sole of your shoe. Tab will return to position shown, unlocking the wheel.
L    ,    
  .    
       .
1. TO LOCK CASTER: Press down on the wheel tab (1) with the sole of your shoe.
The tab will lock into position shown.
2. TO UNLOCK CASTER: Press down on the TOP of the wheel tab (2) with the
sole of your shoe. The tab will return to the position shown, unlocking the
wheel.
A      
    . U  
  . C  3"  
NOT    .
NOTE: Caster appearance may vary from those pictured
here, but operation is the same.
Page 15 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
OPERATING INSTRUCTIONS: ATTENDANT
CASTER OPERATION: LOCK / UNLOCK
1
5" CASTERS: RIGID, TOTAL-LOCK
3" CASTERS
2
NOTE: All four (4) 3" casters are wheel-locking only. 3"
casters DO NOT have TOTAL and DIRECTIONAL locking.
1
2

Pedestal feet are designed for chairs that are
intended to remain in a stationary position.
Use slide-out foot plate with qualified staff assistance only. ONLY GAS-BACK and PRC
models equipped with a FOOT PLATE are suitable for occupant transport (5X08, 5X18,
5X48, 5X58, 6X08, 6X18, 6X48, 6X58, 5P, and 6P). No other models are suitable for
occupant transport.
Prior to transporting an occupant, ensure that the footplate is fully extended and the chair
is in a fully upright, locked position. NEVER transport an occupant with their feet hanging
down, without the footplate in place, as this may cause
serious injury.
Chairs with 3" casters OR without a footplate are NEVER
suitable for patient transport.
The foot plate for the Standard Verō is rated for a
MAXIMUM weight capacity of 350 lbs (158.8 kg).
The foot plate for the XL Verō is rated for a MAXIMUM
weight capacity of 500 lbs (226.8 kg).
1. TO EXTEND: Using your foot, pull out the foot plate as far as it will travel.
The foot plate can now be used by the occupant.
2. TO STORE: Using your foot, push in on the foot plate until it is returned to
the fully stored position.
• The foot plate can be a tripping hazard if not returned to its stored
position after use.
• ALWAYS store the foot plate when not in use.
Page 16 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
FOOT PLATE OPERATION (OPTIONAL FEATURE)
CASTER OPERATION - CONTINUED
PEDESTAL FEET
1
2
NOTE: The foot plate option is ONLY available for models with 5" casters.

Attendant should stand on the RIGHT or LEFT side of chair. Lock ALL four (4) Casters.
1. While occupant is seated in the chair, place one
hand on the arm for support and push back on
the back to recline (1).
*Models with a recline lever (2A)
2. To operate the infinite back recline, use one
hand to operate the recline lever (2A) and the
other hand to push on the upholstered back (2B)
until desired recline angle or maximum recline
has been reached.
3. Release recline lever (2A) to maintain back
position.
Do NOT force the chair back up
or down without fully extending
the recline lever or damage to
the chair may occur.
Page 17 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
RECLINE CHAIR (ATTENDANT POSITION, NON POWER RECLINER MODELS ONLY)
MANUAL ADJUSTMENT CHAIRS (X MODELS)
INFINITE GAS SPRING ADJUSTMENT (Y MODELS)
1
2

Attendant should stand on the RIGHT or LEFT side of chair. Lock ALL four (4) Casters.
1. Pull up on the back to return to upright
position.
2. Attendant can use one hand to push down
on the leg rest (C) until it returns to its stored
position.
Keep hands clear of mechanism
to avoid injury. Use hands on
face of leg rest ONLY.
1. While occupant is reclined in the chair,
attendant should use one hand to operate the
recline lever (A), while using the other hand to
pull up on the back (B).
2. Attendant can use one hand to push down
on the leg rest (C) until it locks into its stored
position.
Keep hands clear of mechanism
to avoid injury.
Release the recline lever (A) once the back
has fully returned to the upright position.
Attendant should NOT use
their foot to return leg rest to its
stored position. Damage to the
mechanism and upholstery may
occur.
NOTE: The recline lever is NOT required to
return leg rest to its stored position.
Page 18 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
RETURN CHAIR TO UPRIGHT POSITION (ATTENDANT POSITION, NON POWER RECLINER MODELS ONLY)
1
2
MANUAL ADJUSTMENT CHAIRS (X MODELS)
INFINITE GAS SPRING ADJUSTMENT (Y MODELS)

Attendant should stand on the RIGHT or LEFT side of chair.
Lock ALL four (4) Casters. Before using Trendelenburg
recline on the occupant, it is highly recommended that the
attendant be thoroughly trained with its proper use.
1. While occupant is in the chair, place the chair into
the fully reclined position (SEE "Recline Chair From
Attendant Position").
2. Once chair is fully reclined, attendant can push down
on the rear of the Trendelenburg lever (A) with their
foot, allowing it to pivot down.
3. Hold the Trendelenburg lever down with your foot and
push down on the chair's back (B). This will shift the
occupant into the Trendelenburg position. Release
Trendelenburg lever.
Chair must be in the fully reclined position
BEFORE occupant can be placed into
Trendelenburg.
DO NOT leave occupant in Trendelenburg angle unattended.
Attendant should be positioned on the RIGHT or LEFT side
of chair.
1. To return chair to the recline position, push down on
seat (recommended) or lift up on chair back.
NOTE: Pushing down on the seat (B) is recommended
for maximum leverage.
NOTE: The chair does NOT lock in the Trendelenburg
position.
NOTE: It is not necessary to press the Trendelberg
lever.
Page 19 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
ACTIVATE TRENDELENBURG POSITION (ATTENDANT ONLY, NON POWER MODELS ONLY)
2
RETURN CHAIR TO RECLINE POSITION (ATTENDANT ONLY) 1
Trendelenburg is a medical patient positioning treatment. It should ONLY be used by trained
personnel AND where indicated by occupant condition.
IMPORTANT
1

Page 20 of 44
Document No.: 006344
Revision: J
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
Copyright © 2020 Winco Mfg., LLC
RECLINE CHAIR (ATTENDANT POSITION, VERO CARE CLINER PRC MODELS ONLY)
1. Attendant should stand on the side of the chair
where the switch panel is located. Lock ALL four
(4) Casters. Some chairs have one or two switch
panels depending on model. An optional pendant is
available.
2. Attendant should check for obstructions and that
occupant's hands and feet are clear of the chair
mechanism before operating the power recline.
3. Press the down button on the switch or pendant to
lower occupant recline angle (2 or 3).
4. Do not try to push the chair back manually to adjust
the recline angle.
←
1
←
2
←
3