Winco Vero Care Cliner Operation manual

VERŌ CARE CLINER
OWNERS OPERATING AND MAINTENANCE MANUAL
IMPORTANT! DO NOT DISCARD THIS MANUAL!
KEEP THIS MANUAL FOR FUTURE REFERENCE AND TRAINING!

SYMBOLS
TYPE B APPLIED PART
FOLLOW INSTRUCTIONS DC VOLTAGE
GENERAL WARNING
SYMBOL FOR MANUFACTURER
TRENDELENBURG
PINCH-POINT WARNING
Page 3 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT!
Do NOT install, maintain or operate this equipment without reading and following
this manual, otherwise injury and/or damage may result.
IF YOU HAVE ANY QUESTIONS OR CONCERNS,
PLEASE CONTACT WINCO MFG., LLC.
Winco assumes no responsibility for damage or injury caused by improper assembly,
installation, use, or maintenance of these products.
No part of this manual may be duplicated in any form without the prior consent of
Winco Mfg., LLC. Unauthorized duplication / distribution of these materials may
result in civil prosecution to the maximum extent allowed by law.
The information contained in this manual is subject to change without notice.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE!
These instructions are available online at no charge.
Visit wincomfg.com to download.
Copyright © 2019 Winco Mfg., LLC
PRODUCTS WITH THE FOLLOWING MARKINGS ARE INTENDED FOR COMMERCIAL USE ONLY:

Page 4 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
TABLE OF CONTENTS
INTENDED USE STATEMENT................................................................................................................................................................ 5
TRANSPORTATION, STORAGE, HANDLING & DISPOSAL............................................................................................................. 5
PREPARATION: BEFORE YOU BEGIN ................................................................................................................................................ 5
IMPORTANT SAFETY INFORMATION................................................................................................................................................. 6
FOR PRODUCTS WITH POWERED OPTIONS (HEAT, MASSAGE, ETC.)......................................................................................................................... 6
FOR ALL CONFIGURATIONS (WITH OR WITHOUT HEAT, MASSAGE, ETC.)................................................................................................................. 8
ASSEMBLY INSTRUCTIONS................................................................................................................................................................. 9
BACK ASSEMBLY ...................................................................................................................................................................................................................... 9
ARMREST COVER INSTALLATION (OPTIONAL ACCESSORY) ......................................................................................................................................... 11
OPERATING INSTRUCTIONS: ATTENDANT....................................................................................................................................... 13
CASTER OPERATION: LOCK / UNLOCK................................................................................................................................................................................ 13
FOOT PLATE OPERATION (OPTIONAL FEATURE)............................................................................................................................................................... 14
RECLINE CHAIR (ATTENDANT POSITION) ........................................................................................................................................................................... 15
RETURN CHAIR TO UPRIGHT POSITION (ATTENDANT POSITION) ............................................................................................................................... 16
PLACING CHAIR IN TRENDELENBURG (ATTENDANT ONLY) .......................................................................................................................................... 17
TRENDELENBURG TO RECLINE (ATTENDANT ONLY)........................................................................................................................................................ 17
SWING-ARM OPERATION (ATTENDANT ONLY).................................................................................................................................................................. 18
TRANSFERRING PATIENT TO CHAIR (SWING-ARM ONLY)............................................................................................................................................. 19
SIDE TABLE OPERATION (OPTIONAL FEATURE) ................................................................................................................................................................ 20
PIVOT TABLE OPERATION (OPTIONAL FEATURE).............................................................................................................................................................. 21
OPERATING INSTRUCTIONS: OCCUPANT ....................................................................................................................................... 22
RECLINE WHILE IN THE SEATED POSITION ........................................................................................................................................................................ 22
RETURNING TO SEATED POSITION....................................................................................................................................................................................... 23
HEAT / HEAT & MASSAGE OPERATION (OPTIONAL FEATURE) ..................................................................................................................................... 24
GENERAL MAINTENANCE..................................................................................................................................................................... 26
GAS CYLINDER OPERATION................................................................................................................................................................................................... 26
GENERAL CARE & CLEANING ............................................................................................................................................................. 26
SPECIFICATIONS.................................................................................................................................................................................... 28
VERŌCARE CLINER OPTIONS............................................................................................................................................................ 29
WARRANTY INFORMATION................................................................................................................................................................. 30

Page 5 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
INTENDED USE STATEMENT
The Verō Care Cliner is a recliner for use in medical settings. It is designed to provide comfort for
patients seated up to eight (8) hours at a time while receiving treatments such as Dialysis or Infusion or
during recovery from surgical procedures where positional adjustments are beneficial. The recliner is
also suitable for general use in many medical settings such as, but not limited to, hospital room chair,
waiting room chair, convalescent home chair, etc.
TRANSPORTATION, STORAGE, HANDLING & DISPOSAL
• The product should be transported in factory packaging, inside an appropriate medium for the
destination, i.e., air/sea cargo containers.
• The product should be stored in an environment that will inhibit rust/mold formation.
• Winco Mfg., LLC recommends not leaving the product in the factory packing in excess of three (3)
months.
• The product should always be handled in a manner consistent with the user instructions and in a
manner to prevent contamination after each use.
• The product has many recyclable components and to the extent practical, all eort should
be used to recycle responsibly. Otherwise the product components shall be disposed of in
accordance with local statues.
PREPARATION: BEFORE YOU BEGIN
1. Carefully examine your product for any damage. Be sure to inspect all components.
IF DAMAGE IS EVIDENT, CONTACT FREIGHT CARRIER OR WINCO IMMEDIATELY.
2. Remove all packaging material and any hardware that was secured for shipping.
3. Carefully remove all components and any included tools and/or parts from the carton.
4. You may need to cut packaging materials with a box cutter or scissors to access the product. Use
CAUTION to avoid personal injury or damage to the product.
5. Save all boxes and packaging material until AFTER you have assembled your product and have
verified that all components are functioning properly. These material are required if it becomes
necessary to return the product.
6. DO NOT install, maintain or operate this equipment without reading and following this manual
otherwise injury and/or damage may result. IF YOU HAVE QUESTIONS OR CONCERNS PLEASE
CONTACT WINCO MFG., LLC.
WINCO ASSUMES NO RESPONSIBILITY FOR DAMAGE OR INJURY CAUSED BY IMPROPER ASSEMBLY,
INSTALLATION, USE, OR MAINTENANCE OF THESE PRODUCTS.

Page 6 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
IMPORTANT SAFETY INFORMATION
FOR PRODUCTS WITH POWERED OPTIONS (HEAT, MASSAGE, ETC.)
When using an electrical appliance, basic precautions should always be followed, including the
following:
To reduce the risk of electric shock always unplug this product from the electrical
outlet before cleaning, maintenance or servicing.
1. Unplug this product from the electrical outlet when not in use.
2. Supervision should be provided when using this product.
3. Use this product only for its intended use as described in this manual.
4. DO NOT use attachments not recommended by the manufacturer.
5. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has
been dropped or damaged, or dropped into water, contact an authorized Winco service center for
instructions.
6. DO NOT carry or pull this product by power supply cord or use the cord as a handle.
7. Keep the cord away from heated surfaces.
8. DO NOT use outdoors.
9. To disconnect, turn all controls to the "off" position, then remove plug from outlet. Pull plug only to
remove cord.
10. Clean switch with a damp cloth only – Warranty will be VOID if liquid is introduced into switch
mechanism.
11. Extension cords are not recommended.
12. DO NOT roll recliner or other equipment over cord.
13. This product is for use on a nominal 120 volt circuit and has a three-pin plug. If the plug does not
fit into the outlet, contact a certified electrician to install the proper outlet. DO NOT MODIFY THE
PLUG IN ANY WAY. No adapter should be used with this product.
14. For an added level of safety; Winco recommends the use of a 120 volt GFCI (ground fault circuit
interrupter) outlet.
1. Never insert pins or attach other metallic fasteners into/onto any part of
this chair.
2. DO NOT use this product if the covering shows signs of deterioration,
such as checking, blistering, or cracking.
3. KEEP DRY - DO NOT operate in a wet or moist condition or environment.
1. Long term, continuous exposure to heat may cause burns. It is recom-
mended that skin in contact with heated area be checked for redness and
blistering during long term usage. DO NOT use on an infant, invalid or in-
capacitated person. DO NOT use on insensitive skin or on a person with
poor blood circulation. If you are uncertain if you should use this product,
please consult your physician about the use of heat and massage.
2. DO NOT crush/pinch heating elements or wiring.

IMPORTANT: PLEASE READ
For Heat & Heat and Massage Chairs:
This equipment is marked with the industry recognized symbol indicating it is a “Class II
Double-Insulated” device as defined by IEC 60601-1. As such, it does NOT require a three
conductor power cord (i.e. one with a ground connection) for safety purposes. While the
equipment can be safely operated with no ground connection, a three conductor power
cord is provided to satisfy customer expectations for typical equipment configuration.
Devices qualifying as double insulated require dierent testing & examination procedures than “Class
I Grounded” devices. If your facility requires the product to be tested, be sure to follow testing &
examination procedures for “Class II Double-Insulated” devices
ISOLATION DIAGRAM FOR HEAT & MASSAGE SYSTEM
A I T
A Basic Operational
B Double Insulated / Reinforced
C Double Insulated / Reinforced
D Double Insulated / Reinforced
E Double Insulated / Reinforced
F Double Insulated / Reinforced
G Inlet FE Pin only connects to inlet & pad
Page 7 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER

IMPORTANT: PLEASE READ
FOR ALL CONFIGURATIONS (WITH OR WITHOUT HEAT, MASSAGE, ETC.)
DO NOT LIFT OR CHANGE CHAIR POSITION BY USING THE LEG REST.
THIS COULD CAUSE INJURY TO THE USER OR DAMAGE TO THE RECLINE MECHANISM AND WILL
VOID WARRANTY.
1. READ AND FOLLOW ALL DIRECTIONS.
2. This is a clinical medical recliner, it is used to position a patient comfortably while receiving various
treatment regimens. Care should always be taken to assess an occupants medical condition PRIOR
to use of recliner and PRIOR to positioning patient in order to determine if this reclining chair is
medically appropriate for a specific occupant's use
3. CAUTION: Use slide-out foot support with staff assistance only.
4. STAY CLEAR of the recliner mechanisms when operating chair.
5. Keep children away from extended foot support (or other similar parts).
6. DO NOT use the recliner if the Trendelenburg Damper / Gas Spring is removed or damaged.
7. DO NOT put hands, feet or clothing into any openings when changing positions on recliner.
Attendant MUST confirm that users arms, legs, hands and feet are safe while changing recliner
positions or SERIOUS INJURY MAY RESULT.
8. Remove or move chair accessories (i.e. side table, pivot table, etc.) out of the way of patients legs
when reclining/changing position of patient.
9. Ensure swing-arms are securely latched after cleaning.
10. ONLY GAS-BACK models equipped with a FOOT PLATE are suitable for patient transport (5X08,
5X18, 5X48, 5X58, 6X08, 6X18, 6X48 & 6X58). No other models are recommended for patient
transport.
11. An occupant should NOT be transported with the swing-arms open except in the event of an
emergency.
12. LOCK casters at all times when chair is stationary AND when a patient is in the chair. UNLOCK
casters ONLY when moving the chair.
13. DO NOT use recliner for transporting in or with ANY type of vehicle or trailer. Winco recliners have
not been tested or approved for use by an occupant in any type of vehicle or trailer.
14. NEVER sit on the chair arms or backrest; SERIOUS INJURY or damage may occur.
15. Periodically check the tightness of all nuts, bolts and screws.
16. Immediately REMOVE FROM SERVICE; Any recliner with broken recline mechanisms, torn
upholstery, or other mechanical or visible damage.
17. NEVER EXCEED the recommended weight capacity.
18. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
19. Chairs are suitable for indoor use only.
USE CAUTION WHEN CLEANING NEAR
MECHANISMS. KEEP FINGERS AWAY FROM PINCH
POINTS.
Page 8 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER

Page 9 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
BACK ASSEMBLY
1. Lock ALL (4) casters on chair base (See "Lock / Unlock Casters")
Keep objects and persons clear of the chair
before performing step 2.
2. Recline mechanism should be in the upright position. Remove
any packaging that may be on the mechanism that might prevent
installation of back.
3. Hold the rear cover, on the lower rear of the back, up exposing
the mounting brackets (A). Lift the upholstered back by its
sides while aligning the mounting brackets with the recline
mechanism (B).
Keep hands clear of connection
points or injury may occur.
• Winco recommends two (2) people be used
to complete Step 3 A and B.
• Be careful not to tear or puncture vinyl.
ASSEMBLY INSTRUCTIONS
1
2
3REAR VIEW OF CHAIR

Page 10 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
BACK ASSEMBLY - CONTINUED
4. Slide the back onto the recline mechanism until the middle
hole of the mounting bracket (A) is aligned with the middle
hole of the recline mechanism (B).
It is recommended that two people be
used for this step.
5. Install knobs (A) (tethered to back) and tighten to a secure fit.
Test to ensure the back has been properly
installed by pulling up on the back. The
back should remain securely in place.
4
5

1. Raise the side table by grasping the center of the table and gently lift into place.
2. Locate large square opening in cover and position over the side table. Stretch the opening over the
side table and slide over side table.
3. Fit the front portion of the Armrest cover over the front of the arm. Pull down tight for best fit.
4. Fit the rear portion of the Armrest cover over the rear of the arm.
5. For Premium Table, you will need to release the table slightly to allow space to tuck the apron into
the gap. Standard Table will have enough room in the upright position.
6. Pull the apron through the gap at the back of the side table completely. (Premium side table
pictured) Smooth wrinkles.
Page 11 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
ARMREST COVER INSTALLATION (OPTIONAL ACCESSORY)
CHAIRS WITH SIDE TABLES
123
456
NOTE:
Cover designs vary based on chair options (i.e. tables, heat/massage, etc.)
NOTE:
Covers are left-hand and right-hand specific.
Make sure you are installing each cover on the correct side.

1. Remove the adjustment knob and the pivot table completely. You MUST remove the knob.
2. Pull the arm rest cover down over the chair arm. Ensure the pivot table bracket is inserted through
the hole in the arm rest cover.
3. Reinstall the pivot table and adjustment knob.
Page 12 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
CHAIRS WITH PIVOT TABLES
ARMREST COVER INSTALLATION - CONTINUED
1 2
3
NOTE:
Covers are left-hand and right-hand specific.
Make sure you are installing each cover on the correct side.

Multiple caster / foot types are available for this recliner: 5" Casters (rigid, total-lock), 3" Casters (wheel-
lock) and Pedestal Feet.
The front two casters are rigid casters. They are NOT designed to swivel in
order to facilitate stable straight steering. In addition, the front locking tabs
are always accessible. When the locking tabs are engaged, caster wheels
will NOT roll.
The rear two casters are total-lock casters. They are designed to swivel
360°. When locking tab is engaged, caster wheels will NOT roll and caster
will NOT swivel.
1. TO LOCK CASTER: Press down on the wheel tab (A). Tab will lock into
position shown.
2. TO UNLOCK CASTER: Press down on the TOP of the wheel tab (B). Tab
will return to position shown.
Total-Lock casters lock the wheel and swivel mechanism when pressing
down on the tab.
L    , 
  /  
.
1. TO LOCK CASTER: Press down on the wheel tab (A). Tab will lock into
position shown.
2. TO UNLOCK CASTER: Press down on the TOP of the wheel tab (B).
Tab will return to position shown.
A    
     
! U   /
  .
Page 13 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
OPERATING INSTRUCTIONS: ATTENDANT
CASTER OPERATION: LOCK / UNLOCK
1
5" CASTERS: RIGID, TOTAL-LOCK
3" CASTERS: TOTAL-LOCK 2
NOTE:
All four 3: casters are wheel-locking only. 3" casters
DO NOT have TOTAL and DIRECTIONAL locking.
1
1

Pedestal feet are designed for chairs that are
intended to remain in a stationary position.
• Foot plate MUST be used with sta assistance.
• The foot plate for the Standard Verō is rated for a MAXIMUM weight
capacity of 350 lbs. (158.8 kg.)
• The foot plate for the XL Verō is rated for a MAXIMUM weight capacity of
500 lbs. (226.8 kg.)
1. TO EXTEND: Using your foot, pull out foot plate as far as it will
travel. Foot plate can now be used by the occupant.
2. TO STORE: Using your foot, push in on the foot plate until it is
returned to the fully stored position
• Foot plate should ONLY be used with the assistance of a qualified
attendant.
• Foot plate can be a tripping hazard if not returned to its stored
position after use.
• ALWAYS store foot plate when not in use.
Page 14 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
FOOT PLATE OPERATION (OPTIONAL FEATURE)
CASTER OPERATION - CONTINUED
PEDESTAL FEET
1
2
NOTE:
The foot plate option is ONLY available for models with 5" Casters.

Attendant should be positioned on the RIGHT or LEFT side of chair.
1. While occupant is seated in the chair, place one hand on the arm for support and push back on the
back to recline.
*Models with a recline lever (A)
1. To operate the infinite back positioning, use one hand
to operate the recline lever (A) and the other hand to
push on the upholstered back (B) until desired position
or maximum recline has been reached.
Release recline lever (A) to maintain position.
Do NOT force the back of chair up
or down without fully extending the
recline lever or damage to the chair
may occur.
Page 15 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
RECLINE CHAIR (ATTENDANT POSITION)
1
MANUAL ADJUSTMENT CHAIRS
INFINITE GAS SPRING ADJUSTMENT
1

Attendant should be positioned on the RIGHT or LEFT side of chair.
1. Pull up on the back to return to upright position.
2. Attendant can use one hand to push down on the leg rest (C)
until it returns to its stored position.
Keep hands clear of mechanism to avoid
injury. Use hands on face of leg rest
ONLY.
1. While occupant is reclined in the chair, attendant should use
one hand to operate the recline lever (A), while using the
other hand to pull up on the back (B).
2. Attendant can use one hand to push down on the leg rest (C)
until it locks into its stored position.
Keep hands clear of mechanism to avoid
injury.
Release the recline lever (A) once the back has fully returned
to the upright position.
Attendant should NOT use their foot to return leg rest to its stored position.
Damage to the mechanism and upholstery may occur.
NOTE:
The recline lever is NOT required to return leg rest to its
stored position.
Page 16 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
RETURN CHAIR TO UPRIGHT POSITION (ATTENDANT POSITION)
1
2
MANUAL ADJUSTMENT CHAIRS
INFINITE GAS SPRING ADJUSTMENT

Attendant should be positioned on the RIGHT or LEFT side of chair.
1. To return chair to the recline position, push down on seat
(recommended) or lift up on chair back.
Attendant should be positioned on the RIGHT or LEFT side of chair.
1. While occupant is in the chair, place the chair into the
fully reclined position. (SEE "Recline Chair From Attendant
Position").
2. Once chair is fully reclined, attendant can push down on the
rear of Trendelenburg lever (A) with their foot, allowing it to
move down.
3. Hold Trendelenburg lever in position & push down on
the chair's back (B). This will shift the occupant into the
Trendelenburg position.
Release Trendelenburg lever.
Chair must be in the fully reclined position
BEFORE occupant can be placed into
Trendelenburg.
NOTE:
Pushing down on the seat (B) is recommended for
maximum leverage.
NOTE:
The chair does NOT lock in the Trendelenburg position.
Page 17 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
PLACING CHAIR IN TRENDELENBURG (ATTENDANT ONLY)
1
2-3
TRENDELENBURG TO RECLINE (ATTENDANT ONLY)
1
Trendelenburg is a medical patient positioning treatment. It should ONLY be used by
trained personnel AND where indicated by patient condition.
IMPORTANT

Attendant should be positioned on the RIGHT or LEFT side of chair.
1. TO OPEN: Press down on red latch handle to unlock Swing-Arm.
• DO NOT leave occupant unattended with either or both swing-
arms unlatched.
• DO NOT transport chair with swing-arms unlatched.
2. TO CLOSE: Push Swing-Arm firmly against frame.
Latch will automatically engage with an audible "click".
Make sure swing-arm latches are properly engaged when swing-arms
are in the closed (latched) position. Test by pulling on arms. The arms
should not swing open if properly engaged.
Swing-arms pivot up to 180°. When both arms are pivoted fully back,
chair width is reduced to 34.5" in order to transport chair through
narrow doorways. In addition, swing-arm can be pivoted back in order
to get a wheel chair or gurney alongside the chair.
3. Unlock both swing-arms and rotate them towards the back of the
chair.
4. Stand behind the chair and use the push handle to maneuver the
chair through the doorway
Transport occupant with chair arms in the open
position in emergency situations only. This should
only be performed by an attendant.
• DO NOT recline chair with either/both swing-arms in the 180°
position.
• DO NOT leave occupant unattended with either or both swing-
arms in any open position.
Page 18 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
SWING-ARM OPERATION (ATTENDANT ONLY)
1
2
3
4

Attendant should be positioned on the RIGHT or LEFT side of chair.
Always lock the casters when the patient enters or exits the chair!
1. Lock all four casters.
2. Place chair into seated or reclined position relative to the
position from which occupant is being transferred.
3. Unlatch one swing-arm and place it into the 180° position.
4. Position gurney or wheel chair next to the chair on the
side with the open swing-arm.
5. Transfer patient to chair following facility safe patient
handling policies.
6. Close the swing-arm.
• DO NOT leave swing-arm open after occupant is
transferred to chair.
• When closing swing-arm, make sure occupants
extremities are clear of swing-arm.
• When closing swing-arm, make sure any foreign
objects are clear of swing-arm travel and latch.
Page 19 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
TRANSFERRING PATIENT TO CHAIR (SWING-ARM ONLY)
2
3

1. TO RAISE TABLE: Grasp center of table and gently raise into place. Table will automatically lock into
place when released.
2. TO LOWER TABLE: Grasp table at the center or on both sides, raise and pivot down in a single
movement.
1. TO RAISE TABLE: Grasp center of table and gently lift into place. Side-table will lock into place with
an audible "click" once fully extended.
2. TO STORE: Lift up on the lever located under the side-table and lower to its stored position.
• DO NOT lean or sit on side tables.
• DO NOT use table for support or assistance when exiting or entering the
chair.
• Keep hands and objects clear of the moving parts of the table mechanism.
Side-tables have been rated for a MAXIMUM weight capacity of 20 lbs. (9.0 kg.)
Page 20 of 32
Document No.: 006344
Revision: I
OWNERS OPERATING & MAINTENANCE MANUAL
VERŌ CARE CLINER
SIDE TABLE OPERATION (OPTIONAL FEATURE)
12
PREMIUM SIDE TABLES
STANDARD SIDE TABLES
12