Winco 8550 Reference guide

Page 1 of 4
006070 Revision P Date 03-08-11 JWC
1. READ AND FOLLOW ALL DIRECTIONS.
2. NEVER stand on table or INJURY MAY OCCUR.
3. NEVER allow user to sleep unattended on table or INJURY MAY OCCUR.
4. NEVER leave an unconscious user unattended on table or INJURY MAY OCCUR.
5. DO NOT use table for transporting user in or with ANY type of vehicle or trailer. Winco tables have not been tested
or approved for use by an occupant in any type of vehicle or trailer.
6. NEVER leave an infant or child unattended on table or INJURY MAY OCCUR.
7. DO NOT put hands, feet or clothing into any openings when changing positions on table. Attendant MUST confirm
that users hands and feet are safe while changing table positions or SERIOUS INJURY MAY RESULT.
8. Periodically, recheck tightness of all nuts, bolts and screws.
9. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
10. NEVER EXCEED the recommended weight capacity of 400 lbs. (181.4 kg).
11. SAVE THESE INSTRUCTIONS for future reference and training.
8550
Recovery Couch
CUSTOMER INSTRUCTIONS
Tools needed:
•Phillips-head screwdriver
•7/16” wrench (multiple size wrench included)
•Scissors or box cutter
•Cardboard shipping container (stays under table during assembly to protect upholstery)
•- If using powered tools always start hardware together by hand first & wear safety goggles
1. After checking your product for any shipping damage, table needs to be positioned upside-down on cardboard or
protective surface. Remove all packing material and hardware that was secured for shipping. Cut tape on corners of
box so that cardboard will lay flat while you assemble table.
2. You will find two Welded Leg Assemblies, in-between and attached to the Table Frame Rails. Pivot up the (2)
Welded Leg Assemblies, (see sketch).
NOTE: The leg assemblies have braces that need to align with two threaded holes in the wood
of the Upholstered Top.
3. Install (4) ¼-20 x 1-½” screws through (2) holes in each cross brace of the Welded Leg Assemblies, and into (2)
threaded holes (each end) in the wood of the Upholstered Top, as shown in sketch.
NOTE: Do not fully tighten at this time.
4. Place (4) ¼-20 x 1-½” carriage bolts into the (4) holes through the Lower Leg Brace of the Welded Leg Assemblies,
as shown. Heads of screws should face the ends of table, for better appearance.
5. Align the Welded Brace Assembly (smoothest side up) with the (4) screws that you just installed on step 4,and
fasten with (4) ¼-20 nuts.
PLEASE READ AND FAMILIARIZE YOURSELF WITH
A
LL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
If you have trouble understanding these instructions contact your dealer or Winco customer support, [phone]
before attempting to use this product; otherwise injury may occur.
8550 Weight Capacity = 400 lbs. (181.4 kg.)
Winco assumes no responsibility for damage or injury caused by improper assembly,
installation, use, or maintenance of these products.

Page 2 of 4
006070 Revision P Date 03-08-11 JWC
6. TIGHTEN ALL FASTENERS AT THIS TIME (including the nuts & screws holding the Welded Leg Assemblies to the
Table Frame Rails – see sketch).
7. Install the four (4) Threaded Inserts with Glide Feet into the ends of the table legs.
8. Using at least two people, turn table upright.
9. Remove (1) of the white plastic caps on the Paper Holder Rod and install into the (2) Paper Rod Clamps, replace
cap. Adjust (4) 5/16” Adjustable Glides to level table.
Optional Shelf installation:
10. Double-sided tape has been installed on the Welded Brace Assembly.
11. Before removing paper on tape, “test fit” the shelf. Shelf should be approximately ¼” from edge of Lower Leg Brace.
12. Once you are certain of where you will position the shelf, peel off the paper to expose adhesive.
13. Carefully position shelf in place on adhesive.
Vinyl Strap Adjustment – Should the vinyl strap on your Winco table need to be adjusted, unscrew the screw that
currently holds either side of it in place. Pierce another hole in the strap to give desired tension and re-insert screw.
Wrinkles in Vinyl – Storage and shipping can cause wrinkles of the vinyl on your Winco table. This is normal. Please
allow 1-2 weeks at room temperature (approx. 70 degrees) to allow for vinyl to expand back to original appearance.
If the Optional Shelf and Reinforced Welded Brace Assembly have been ordered; make sure that the smooth surface
(side with tape) of the Reinforced Welded Brace Assembly will face upward (when the table is in the upright position)
prior to fastening to Welded Leg Assemblies.
After peeling paper from adhesive tape:
Use damp sponge to moisten tape to allow shelf to be adjusted during install.
Once ta
p
e is dr
y
shelf will sta
y
in
p
lace.
Do not over tighten nuts and bolts.
Periodically check all fasteners for
tightness.

Page 3 of 4
006070 Revision P Date 03-08-11 JWC
Items factory installed on table: Qty. Sizing chart – part number
Table Frame 2 222700
¼-20 x 2½ screw 4 566519
¼-20 lock nut 4 566204
Paper Holder Rod 1 222705
Paper Rod Strap (bracket) 2 501810
Upholstered Top 1 CALL FOR P/N
1” x 2” rectangular insert caps, (gray) 4 701010
VinylStrap 1 271500
Items included with table (NOT factory installed):
Welded Leg Assembly (19 inch) 2 222708
Adjustable Glide Foot (threaded) 4 500350
Threaded Leg Insert (for Glide Foot) 4 500105
Welded Brace Assembly (no shelf) 1 222720
Welded Brace Assembly (with shelf) 1 222730
Shelf, plain 1 263960
¼ - 20 x 1½ carriage bolt 4
leg assy. to cross brace 566401
¼-20 X 1½” screw 4
leg assy. to table bottom 566506
¼-20 lock nut 4
welded brace assy. to both leg assys. 566204

Page 4 of 4
006070 Revision P Date 03-08-11 JWC