Winco 4300 User manual

Page 1 of 4
0006010 Rev R Date 06-26-13 JWC
1. READ AND FOLLOW ALL DIRECTIONS.
2. NEVER place stool on a cart, table, stand or other objects; Stool could fall and INJURY MAY OCCUR.
3. DO NOT allow children to play with stool; Stool has moving parts and INJURY MAY OCCUR.
4. Periodically, recheck tightness of all nuts, bolts and screws.
5. Stool must ALWAYS be positioned on level surface.
6. NEVER stand or ride on stool; Stool not to be used for user transport; INJURY MAY OCCUR.
7. DO NOT use stool in or with ANY type of vehicle or trailer. Winco stools have not been tested or approved for use
by an occupant in any type of vehicle or trailer.
8. Immediately remove from service; Any stool with broken or missing parts, torn vinyl, or other visible damage.
9. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
10. NEVER EXCEED the recommended weight capacity of 250 lbs. (113.4 kg).
11. SAVE THESE INSTRUCTIONS for future reference and training.
4300-4350-4400-4450
Gas Lift Stools
CUSTOMER INSTRUCTIONS
Base Assembly
1. Place the Upholstered Seat on a clean, flat surface, cushion side down.
2. Push the stem of the Gas Cylinder into the Stool Swivel Plate (pre-attached to the Upholstered Seat).
3. Slide the Foot Ring (optional) over the Gas Cylinder, so that the Foot Ring faces the bottom of the
Upholstered Seat.
4. Place the Stool Base over the end of the Gas Cylinder and gently tap it down.
5. Install all (5) Casters into the Stool Base. (The stem of the caster should snap into place)
6. Turn the entire assembly upright on the floor
7. If you have the optional Foot Ring, tighten the Foot Ring Adjusting Knob now.
Back Assembly (models 4350 & 4450 only)
8. Slide the steel Slotted Back Strap into the Stool Swivel Plate.
9. Insert the Back (depth) Adjusting Knob to lock the Slotted Back Strap into place.
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
If you have trouble understanding these instructions contact your dealer or Winco customer support, [phone]
before attempting to use this product; otherwise injury may occur.
4300-4350-4400-4450 Weight Capacity = 250 lbs. (113.4 kg.)
Winco assumes no responsibility for damage or injury caused by improper assembly,
installation, use, or maintenance of these products.

Page 2 of 4
0006010 Rev R Date 06-26-13 JWC
Operation of Gas Lift Stool
10. The stool is now ready for use. To raise the stool seating height; lift Release Handle without weight on
seat.
11. To lower stool seating height; Lift the Release Handle while sitting on the seat; Release the handle when
desired height is reached.
12. Position the Upholstered Back and Foot Ring into the desired positions using the Adjusting Knobs.
Important -To ensure proper operation of your Gas Lift Stool; periodically recheck tightness of all fasteners.
Wrinkles in Vinyl – Storage and shipping can cause wrinkles of the vinyl on your Winco stool. This is normal.
Please allow 1-2 weeks at room temperature (approx. 70 degrees) to allow for vinyl to expand back to original
appearance.
Visit our website www.wincomfg.com/product-documents/parts-lists for a complete parts list catalog of your chair or
call Customer Service @ 1-800-237-3377 to request it by mail.
Periodically recheck tightness of all fasteners, and never stand on the Upholstered Seat.

Page 3 of 4
0006010 Rev R Date 06-26-13 JWC
Other Quality Winco Medical Furnishings You May Be Interested In:
Visit us online at www.wincomfg.com

Page 4 of 4
0006010 Rev R Date 06-26-13 JWC
Design, appearance, parts, & construction are subject to change without notice