Winix C545 User manual

FRONT
PACKAGE CONTENTS
BACK
Control Panel
* For a Certified Refurbished Air Purifier, there will be 4 New Carbon Filters and 1 True HEPA Filter included;
equivalent to a 1-year supply.
Front Panel
Air Outlet
Vent
Handle
Power Plug
Unit (1) Pre-Filter
(8) Activated Carbon Filters
(2) True HEPA Filters
Alexa Setup Guide /
Wi-Fi Setup Guide
User
Manual
WHERE TO USE
MODEL PART DIAGRAM
12~18 in
12~18 in
Allow 12 ~ 18 in. of space between TVs, radios, and other
electronics.
Electromagnetic interference from certain
electronics may cause product malfunction.
Place indoors away from direct sunlight. Direct exposure
may cause product malfunction or failure.
Only place on hard, flat surfaces. Flimsy or slanted
surfaces may result in abnormal noise and vibrations.
Allow at least 12 ~ 18 in. from walls for maximum air flow
01. Auto Mode Indicator - The LED "Auto" light
will indicate when Auto Mode is activated.
02. Air Quality Indicator - Color coded LED
light indicates one of three levels of Air Quality:
Red (poor), Amber (fair), and Blue (good).
03. Fan Speed Indicator - Indicates the current
fan speed.
04. Sleep Mode Indicator - The LED "Sleep"
light will indicate when Sleep Mode is on.
05. Filter Replacement Indicator - LED light
indicates when it is time to change the filter.
06. Filter Reset Button - After replacing the
True HEPA Filter, use a small object such as a
paper clip, to press and hold the Filter Reset
Button for at least 5 seconds until the Filter
Replacement Indicator turns off.
07. Smart Sensor - Detects the amount of
odorous gas in the environment. When in Auto
mode, the fan speed adjusts according to the
detected amount of gas.
08. Power Button - Turns the unit on or off.
During the first 30 seconds of powering up, the
Air Quality Indicator will cycle through Blue,
Amber and Red colors.
• Smart sensor takes approximately 4 minutes
to detect the air quality in the environment
before normal operation begins.
09-1. Fan Speed/Auto/Sleep Buttons - Use the
Fan Speed arrow buttons to set the desired
fan speed. Fan Speeds cycle over in this
sequence: Auto, Low, Medium, High, Turbo,
Sleep, Auto.
Auto Mode: Automatically adjusts fan speeds
according to your indoor air quality. The fan
speed will adjust to low when air quality is good,
medium when fair, and to high when poor.
Sleep Mode: When Sleep Mode is activated,
the Air Quality Indicator LED light is disabled.
• Fan speed will automatically set to minimum
speed (lower than 'Low') which will be
nearly silent. When Sleep Mode is active,
PlasmaWave®will be disabled, but it can be
turned back on.
09-2. PlasmaWave
®
Button - Press and hold
the buttons + for 3 seconds
Press the Plasmawave
®
button when the unit
is on to enable or disable this feature. By
default, PlasmaWave
®
is enabled whenever the
unit is powered on. When the unit is running,
you may hear a chirping or buzzing sound.
The sound is from large particles passing
through PlasmaWave
®
, it is normal and does
not signify product failure.
10. PlasmaWave
®
Indicator - Indicates
whether PlasmaWave
®
is enabled or disabled.
11. Wi-Fi Button -
Press for 3 seconds to
activate pairing mode. When Wi-Fi is paired,
press the button to turn Wi-Fi off or back on.
12. Wi-Fi Indicator - Enables or disables the Wi-
Fi feature. When in the pairing state, the Wi-Fi
LED flashes. When paired successfully, the Wi-Fi
LED will be a solid white light.
13. Light Sensor - Detects the amount of
ambient light in the environment. When in Auto
Mode, the light sensor detects when to put the
unit into Sleep Mode.
Winix Smart Wi-Fi Setup - Refer to the Wi-Fi
Guide Guide provided inside the box.
CONTROL PANEL
07 08 09 11 13
02 03 04 05 0601
1210
When to Replace Filters
Filter Indicator Light When to Service When to Replace
Pre-Filter none Every 14 days Permanent
Activated Carbon Filter none
CAN'T BE WASHED
Every 3 months
True HEPA Filter
Lasts Approx.
12 months
• When the Check Filter Indicator LED is on, it is time to replace the Filter.
• Intervals between filter replacement may vary depending on environment.
MAINTENANCE
3True HEPA Filter
2Activated Carbon Filter 4PlasmaWave®
Pre-Filter
1
4-STAGE AIR PURIFICATION
INITIAL OPERATION
REPLACING FILTERS
CLEANING CARE
Cleaning the Filters:
Use a vacuum cleaner or soft brush to clean
the Pre-Filter.
• If it is excessively soiled, rinse in room
temperature water. Do not use detergent or
soap.
Allow the filter to dry for 24 hours or
more before using.
Intervals between filter
cleaning may vary depending on the air
quality. Do not use hot water over 104oF or
volatile fluids such as paint thinner.
Cleaning the Exterior & Interior:
Wipe with a soft damp cloth using room
temperature water.
• Afterwards, wipe it down with a dry cloth.
Open the front panel and clean the interior
with a vacuum cleaner.
•For optimal performance, clean every 1-2
months.
1712-0096-00
Resetting Filter Life:
After replacing your True HEPA Filter, place the Pre-Filter back in and close the Front Panel.
While the unit is on, hold the Filter Reset Button for at least 5 seconds until you hear the beep.
After the beep, the Filter Replacement Indicator will disappear. The True HEPA Filter is now reset.
1. Remove the front panel by grasping its upper edge
and gently pulling forward.
2. Remove the Pre-Filter, then the bag of filters behind it.
3. Remove filters from protective plastic bag.
4. Install the filters until they fit securely in place.
03. True HEPA Filter (back)
02. Activated Carbon Filter (middle)
01. Pre-Filter (front)
5. After filters are installed, close the front panel.
6. Insert the power cord into an electrical outlet.
Latch
01
02
03
Latch
NOTICE
• When cleaning the unit, always unplug the power cord
first and then wait until the unit has cooled down.
• Never disassemble, repair, or modify this unit yourself.
• Do not use flammable sprays or liquid detergents.
• Do not allow children to clean or maintain the unit.
• Before cleaning or maintaining, ensure unit is unplugged.
• Do not use benzene, alcohol, or other volatile fluids,
which may cause damage or discoloration
.
SPECIFICATIONS
Model C545
Voltage AC 120 V / 60 Hz
Power Rate 65W
Dimensions 13.7"W × 8.4"D × 20.5"H
Weight 11 lbs
Filter SKU Filter S: 1712-0096-00
Exterior design, and product specifications may be changed
without prior notice to improve product performance.
Contact Winix for product related inquiries and customer service
•Dedicated Call Center: [phone]
•Website: www.winixamerica.com
To expedite service, please specify the model name and number, the nature of the problem, your
contact information, and your address.
For Troubleshooting or Frequently Asked Questions, please visit: https://winixamerica.com/faq/
Air Purification means it
removes inanimate particles

SAFETY INSTRUCTIONS
Thank you for purchasing a Winix air purifier. This product is for household use only.
• Do not repair or modify the unit. All repairs
should be completed by a qualified technician.
• The plug for this unit is polarized with one blade
wider than the other. Do not force the plug into
an electrical outlet. Do not alter the plug in
any way. If the plug does not fit into the outlet,
reverse the plug. If it still does not fit, contact a
qualified technician to install a proper outlet.
• Do not use if the power cord or plug is damaged
or the connection to the wall outlet is loose.
• Use AC 120V only.
•Do not damage, break, forcefully bend, pull,
twist, bundle, coat, pinch, or place heavy
objects on the power cord.
•Periodically remove dust from the power plug.
This will reduce the risk of shock due to humidity
build up.
• Remove the power plug from the outlet before
cleaning the unit. When removing the power
plug, grasp by holding the plug itself, never hold
by the cord.
• If the power plug is damaged, it must be
replaced by the manufacturer or a qualified
technician.
• Remove the power plug from the outlet when
not in use.
• Do not handle the power plug with wet hands.
• Do not operate the unit when using indoor
smoke-generating insecticides.
• Do not clean unit with benzene or paint thinner.
Do not spray insecticides on the unit.
• Do not use the unit where it is humid or
where the unit may become wet, such as the
bathroom.
• Do not insert fingers or foreign objects into air
intake or outlet.
• Do not use the unit near flammable gases. Do
not use near cigarettes, incense, or other spark-
creating items.
• Unit will not remove carbon monoxide emitted
from heating appliances or other sources.
• Unplugging the product disconnects the remote
functions.
IMPORTANT PRECAUTIONS FOR USING YOUR
AIR PURIFIER:
• Do not block the intake or outlet vents.
• Do not use near hot objects, such as a stove.
•Do not use where the unit may come into contact
with steam.
• Do not use the unit on its side.
• Keep away from products that generate oily
residue, such as a deep fryer.
• Do not use detergent to clean the unit.
• Do not operate without a filter.
• Do not wash and reuse the True HEPA Filter.
• Hold the handle on the back of the unit to
transport.
• Do not hold by the front panel.
• Do not stick any small objects into the air outlet
vents or fan.
IMPORTANT CAUTIONS FOR USING YOUR AIR PURIFIER:
WARNING:
Follow the instructions in this manual to reduce the risk of electric shock, short circuit, and/or fire.
Do not place below any electrical outlet.
Do not have the unit facing into wind or
drafts.
Do not pull on the power cord when
unplugging the unit.
Do not tie or knot the power cord when
unit is in operation.
If the unit becomes submerged in water,
unplug it and contact customer service.
Do not unplug or move the unit while in
operation.
Do not plug additional appliances into the
same outlet or power supply.
Do not touch the plug with wet hands.
Unplug the unit when not in operation for
extended periods of time.
Do not place around heating elements.
The cord can become damaged by
forcefully bending, pulling, twisting,
bundling, pinching or placing heavy
objects on it.
Do not install in any sort of motor or
transport vehicle (trucks, boats, ships,
etc.).
Do not place in an area with excessive
amounts of noxious gases.
Do not place near any flammable
materials (aerosols, fuel, gases, etc.).
Do not place in excessively humid areas
where the unit may become wet.
Do not place unit closer than 12 inches
from the wall during operation. It may
cause condensation on the wall and the
surrounding area.
Do not use around mist or fumes from
industrial oil or around large quantities of
metallic dust.
SAFETY AND CAUTIONS
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to
the following two conditions:
• This device may not cause interference.
• This device must accept any interference, including interference that may cause undesired
operation of the device.
"In French: Cet appareil contient des émetteurs/récepteurs exemptés de licence et conformes
aux normes Innovation, Science et Economic. RSS(s) sans licence de Développement Canada. Le
fonctionnement est soumis aux deux conditions suivantes:
• cet appareil ne doit pas causer d’interférences nuisibles, et
•cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant provoquer
un fonctionnement non souhaité."
TWO YEAR WARRANTY
The terms of the warranty are as follows:
1. This product is manufactured under stringent quality control and inspections.
2. The warranty will be voided if product failure is a result of negligence or misuse by the consumer.
3. A proof of purchase must be presented upon claiming a Product Warranty.
4. Store the proof of purchase in a safe place or register your product on winixamerica.com to
upload your proof of purchase.
5. This warranty is valid only in the USA and Canada.
• The product warranty is printed on the back of this guide This product is manufactured
for use only in USA / CA. This product is suitable for 120 V only.
C545 USER MANUAL
AIR PURIFIER
The energy efficiency of this ENERGY STAR
certified model is measured based on a ratio
between the model’s CADR for smoke and the
electrical energy it consumes, or CADR/Watt.
Before operating this equipment, carefully read and
follow these safety cautions.
Ensure filters are inserted before running unit.
Running the unit without filters can shorten the
lifespan of the unit and cause electric shock or injury.
Be sure foreign objects are NOT inserted into the
vents on the unit.
Objects can include pins, rods, and
coins.
Do not touch any part of the interior of the unit with
wet hands.
The high voltage may cause electric shock.
Ensure unit intake and outlet vents do not
become blocked.
Blockage may lead to increased
internal termperatures,
causing product failure and
deformation.
Do not use the unit as a step stool or place heavy
objects on the unit.
Personal injury may occur or
product failure and deformation.
WARNING
Follow these instructions to reduce the
risk of serious injury or death and to
reduce risk of damaging the unit.
• If the power cord is damaged, it must be
replaced by a special cord. Reassembly
is available from the manufacturer or its
service agent.
• This appliance is not intended for use
by a person (including children) with
reduced physical sensory or mental
capabilities, or lack of experience and
knowledge of the unit, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
• This unit is not intended to be used to
preserve documents or art conservation.
For more warranty information visit:
https://winixamerica.com/terms-and-conditions/
* Certified Refurbished Air Purifiers come with a 1-year warranty. All Winix Certified Refurbished Air Purifiers go
through a detailed inspection and refurbishment process to ensure all quality and performance standards are met.