Winix HR900 User manual

WHERE TO USE
12~18 in
12~18 in
Allow 12 ~ 18 in. of space between TVs, radios, and other
electronics
Electromagnetic interference from certain electronics may cause
product malfunction.
Place indoors away from direct sunlight
Direct exposure may cause product malfunction or failure.
Only place on hard, flat surfaces
Flimsy or slanted surfaces may result in abnormal noise and
vibrations.
Allow at least 12 ~ 18 in. from walls for maximum air flow
True HEPA Filter
04
Washable AOC™
Carbon Filter
03
PlasmaWave
®
05
Pre-FilterPet Filter
01 02
5-STAGE AIR PURIFICATION
FRONT
PACKAGE CONTENTS
BACK
Air Outlet
Vent
Handle
Control Panel
Front Panel
Smart
sensor
Unit
Power Plug
(1) Pre-Filter
(1)
Washable AOC™
Carbon Filter
(1) True HEPA Filter
User Manual
12 Pet Filter
MODEL PART DIAGRAM
08 09 10 11 12 13
01 06 0702 050403
01. Smart Sensor
Detects the amount of odorous gas in the
environment. When in Auto mode, the fan speed
adjusts according to the detected amount of gas.
02. Filter Replacement Indicator
LED light indicates when it is time to change the
filter.
03. Filter Reset Button
After replacing the filters, turn the unit on and use a
thin object, such as a paper clip, to press the Filter
Reset Button for 5 seconds.
04. Fan Speed Indicator
Indicates the current fan speed.
05. PlasmaWave
®
Indicator
Indicates whether PlasmaWave
®
is enabled or
disabled.
06. Timer Indicator
If timer has been set, the LED light indicates the set
time of operation.
07. Child Lock Indicator
LED light indicates whether Child Lock Mode is
enabled or disabled.
08. Light Sensor
Detects the amount of ambient light in the
environment.
09. Power Button
Turns the unit on or off.
• During the first 4 minutes of powering up, the
Air Quality light will flash as the Smart Sensors
measure the air quality in the environment, after
which normal detect will begin.
10. Mode Button
Press to cycle through to set the mode of operation
(Auto, Sleep). The unit will default to Auto with
PlasmaWave
®
enabled when first powered on.
Auto Mode:
• Auto Mode automatically adjusts fan speeds
according to your indoor air quality. The fan speed
will adjust to low when air quality is good, medium
when fair, and to high when poor.
CONTROL PANEL
INSTALLING THE PET FILTER
INITIAL OPERATION
1. Remove the front panel by grasping its upper
edge and gently pulling forward.
2. Remove the Pre-Filter, then the plastic bag of
filters behind it.
3. Remove filters from protective plastic bag.
4. Install the filters until they fit securely in place.
04. True HEPA Filter (back)
03. Washable AOC™ Carbon Filter (middle)
02. Pre-Filter (front)
5. After filters are installed, close the front panel.
6. Insert the power cord into an electrical outlet.
Latch
02
03
04
Latch
When to Replace Filters
Filter Indicator Light When to Service When to Replace
Pre-Filter none Clean once every 14 days Permanent
Washable AOC™ Carbon Filter none * Clean once every 3 months
Lasts Approx.12 months
True HEPA Filter Can NOT be WASHED
• When the Check Filter Indicator LED is on, it is time to replace the True HEPA Filter and Washable AOC™
Carbon Filter.
• Intervals between filter replacement may vary depending on environment.
* Filter performance may decrease after each wash and depending on contamination level prior to washing.
MAINTENANCE
REPLACING FILTERS
Resetting Filter Life:
After replacing your True HEPA Filter, place the Pre-Filter back in and
close the Front Panel. While the unit is on, use a small, thin object (such
as a paperclip) to hold the Filter Reset Button for at least 5 seconds
until you hear the beep. After the beep, the Filter Replacement
Indicator will disappear. Your Winix True HEPA is now reset.
CLEANING CARE
Cleaning the Filters:
Use a vacuum cleaner or soft brush to clean the Pre-
Filter
• If it is excessively soiled, rinse in room
temperature water.
• Do not use detergent or soap.
• Allow the filter to dry for 24 hours or more before
using.
• Intervals between filter cleaning may vary
depending on the air quality in the environment.
To clean the Washable AOC
TM
Carbon Filter, remove
from unit and rinse under lightly running room
temperature water.
• Do not use detergent or soap.
• Allow the filter to dry for 24 hours or more before
using.
• Do not use hot water over 104
o
F.
Cleaning the Smart Sensor:
1. Use a damp cotton swab to wipe
the lens and intake area of the
Smart Sensor.
• To clean the sensor area, use
only water. Do not use volatile
substances such as alcohol or acetone.
2. Wipe away any remaining moisture with a dry
cotton swab.
Cleaning the Exterior & Interior:
1. Open the front panel and clean the interior with
a vacuum cleaner.
• A handheld vacuum or hose attachment will
work best.
2. Dampen a cloth with room temperature water and
wipe down the interior and exterior of the unit.
3. Wipe the unit down with a clean, dry cloth.
• Ensure no moisture remains before plugging
the unit back in.
* For optimal performance, clean every 1 - 2 months.
NOTICE
• When cleaning the unit, always unplug the
power cord first and then wait until the unit has
cooled down.
• Never disassemble, repair, or modify the unit
yourself.
• Do not use flammable sprays or liquid
detergents.
• Do not allow children to clean or maintain the
unit.
• Before cleaning or maintaining, ensure unit is
unplugged.
• Do not use benzene, alcohol, or other
volatile fluids, which may cause damage or
discoloration.
Sleep Mode:
• When Sleep Mode is activated, the Air Quality
Indicator LED light is disabled.
• Fan speed will automatically set to minimum speed
(lower than 'Low') which will be nearly silent.
• When Sleep Mode is active, PlasmaWave
®
will be
disabled, but it can be turned back on.
Manual Mode (Setting fan speed):
Users can opt to manually set the fan speed to Low,
Medium, High, or Turbo.
• Press the Mode Button to select the desired fan
speed.
• The Mode LED light will indicate the selected fan
speed and operation will begin.
11. PlasmaWave
®
Button
Enables or disables PlasmaWave
®
.
• Press the PlasmaWave
®
button when the unit is
on to enable or disable this feature.
• PlasmaWave
®
works to remove harmful airborne
contaminants.
"When the unit is running, you may hear a chirping
or buzzing sound. The sound is from large particles
passing through PlasmaWave
®
, it is normal and does
not signify product failure."
Air Quality
Indicator
12. Timer Button & Air Quality
LED Light
• Press to cycle through and set
desired length of operation.
(1hr, 4hr, 8hr, [NO TIMER])
• To turn the Air Quality LED light
on or off, press and hold the
Timer Button for 3 seconds.
• When on, the LED light will
indicate the current indoor
air quality according to three
levels. BLUE(good), AMBER
(fair), RED (poor).
13. Child Lock
Press and hold the Child Lock Button for 3 seconds
to enable or disable the feature.
• When the Child Lock indicator is lit, the feature is
enabled.
• When Child Lock is enabled, the control panel is
locked and the settings cannot be changed.
• To disable, press and hold the Child Lock Button
again for 3 seconds.
For optimal performance, only genuine Winix filters
should be used with your Winix Air Purifier
1. Remove the front panel by grasping the upper
edges and gently pulling the front panel toward
yourself. The latch at the lower edge of the
panel must be released from its position.
2. Press the tabs on the top edge of the Pre-Filter
to remove it.
3. Remove the liner around the outside of the
Pre-Filter to reveal the adhesive tape.
4. Attach the Pet Filter to the front of the Pre-Filter.
Press the adhesive tape around the edge of the
Pet Filter to adhere it to the Pet Filter.
5. Insert the Pre-Filter. Insert the bottom tabs into the
slots on both sides of the lower part of the unit.
Rotate the top of the filter upward and snap the upper
tabs into the slots securing the Pre-Filter in place.
6. Replace the front panel by first inserting the latch
at the bottom edge into the base of the unit, then
rotate the panel upward toward the top of the
unit until it magnetically snaps closed.
Latch
1 2 3 4 5 6
Latch
Tabs Tabs
Filter Replacement Period
Filter Type Replacement Period Quantity
Pet Filter 1 Month 12 Per Pack
• The Replacement Period may be different
depending on the surrounding environment.
Customer Service and Purchase Inquiry
www.winixamerica.com l [email protected]
LensLens
Cotton
swab
Air Purification means it
removes inanimate particles

The energy efficiency of this ENERGY STAR
certified model is measured based on a ratio
between the model’s CADR for smoke and the
electrical energy it consumes, or CADR/Watt.
Do not pull on the power cord when
unplugging the unit.
Do not tie or knot the power cord when unit
is in operation.
If the unit becomes submerged in water,
unplug it and contact customer service.
Do not unplug or move the unit while in
operation.
Do not plug additional appliances into the
same outlet or power supply.
Do not touch the plug with wet hands.
Unplug the unit when not in operation for
extended periods of time.
Do not place around heating elements.
Do not use around mist or fumes from
industrial oil or around large quantities of
metallic dust.
The cord can become damaged by forcefully
bending, pulling, twisting, bundling, pinching
or placing heavy objects on it.
Do not install in any sort of motor or
transport vehicle (trucks, boats, ships, etc.).
Do not place in an area with excessive
amounts of noxious gases.
Do not place near any flammable materials
(aerosols, fuel, gases, etc.).
Do not have the unit facing into wind or
drafts.
Do not place below any electrical outlet.
Do not place in excessively humid areas
where the unit may become wet.
Do not place unit closer than 12 inches
from the wall during operation. It may
cause condensation on the wall and the
surrounding area.
SAFETY AND CAUTIONS
Before operating this equipment, carefully read and
follow these safety cautions.
Ensure filters are inserted before running unit.
Running the unit without filters can shorten the
lifespan of the unit and cause electric shock or injury.
Be sure foreign objects are NOT inserted into the
vents on the unit.
Objects can include pins, rods, and coins.
Do not touch any part of the interior of the unit with
wet hands.
The high voltage may cause electric shock.
Ensure unit intake and outlet vents do not become
blocked.
Blockage may lead to increased internal
termperatures, causing product failure and
deformation.
Do not use the unit as a step stool or place heavy
objects on the unit.
Personal injury may occur or product failure and
deformation.
WARNING
Follow these instructions to reduce the risk of
serious injury or death and to reduce risk of
damaging the unit.
• If the power cord is damaged, it must be replaced
by a special cord. Reassembly is available from
the manufacturer or its service agent.
• This appliance is not intended for use by
a person (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge of the unit, unless
they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that they
do not play with the appliance.
• This unit is not intended to be used to preserve
documents or art conservation.
SAFETY INSTRUCTIONS
Thank you for purchasing a Winix air purifier. This product is for household use only.
• Do not repair or modify the unit yourself.
• All repairs should be completed by a
qualified Winix technician.
• The plug for this unit is polarized with one
blade wider than the other. Do not force the
plug into an electrical outlet. Do not alter the
plug in any way. If the plug does not fit into
the outlet, reverse the plug. If it still does not
fit, contact a qualified technician to install a
proper outlet.
• Do not use if the power cord or plug is
damaged or the connection to the wall outlet
is loose.
• Use AC 120 V only.
• Do not damage, break, forcefully bend, pull,
twist, bundle, coat, pinch, or place heavy
objects on the power cord.
• Periodically remove dust from the power
plug. This will reduce the risk of shock due
to humidity build up.
• Remove the power plug from the outlet
before cleaning the unit. When removing the
power plug, grasp by holding the plug itself,
never hold by the cord.
• If the power plug is damaged, it must be
replaced by the manufacturer or a qualified
technician.
• Remove the power plug from the outlet when
not in use.
• Do not handle the power plug with wet
hands.
• Do not operate the unit when using indoor
smoke-generating insecticides.
• Do not clean unit with benzene or paint
thinner. Do not spray insecticides on the
unit.
• Do not use the unit where it is humid or
where the unit may become wet, such as the
bathroom.
• Do not insert fingers or foreign objects into
air intake or outlet.
• Do not use the unit near flammable gases.
Do not use near cigarettes, incense, or other
spark-creating items.
• Unit will not remove carbon monoxide
emitted from heating appliances or other
sources.
IMPORTANT CAUTIONS FOR USING YOUR AIR PURIFIER:
WARNING: Follow the instructions in this manual to reduce the risk of electric shock, short circuit,
and/or fire.
TWO YEARS WARRANTY
The terms of the warranty are as follows:
1. This product is manufactured under stringent
quality control and inspections.
2. The warranty will be voided if product failure
is a result of negligence or misuse by the
consumer.
3. A proof of purchase must be presented upon
claiming a Product Warranty.
4. Store the proof of purchase in a safe place or
register your product on winixamerica.com to
upload your proof of purchase.
5. This warranty is valid only in the USA and
Canada.
* for more information visit
https://winixamerica.com/terms-and-conditions/
Product Name Air Purifier
Model Name HR900
Purchase Date
Warranty Period Two (2) Years
Place of Purchase
Place of Purchase
tel.
Customer
Address
Name
Tel.
After purchase, be sure to complete all of the above
information.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two
conditions:
• This device may not cause interference.
• This device must accept any interference, including interference that may cause undesired operation of
the device.
"In French: Cet appareil contient des émetteurs/récepteurs exemptés de licence et conformes aux normes
Innovation, Science et Economic. RSS(s) sans licence de Développement Canada. Le fonctionnement est
soumis aux deux conditions suivantes:
• cet appareil ne doit pas causer d’interférences nuisibles, et
• cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant provoquer un
fonctionnement non souhaité."
HR900 USER MANUAL
AIR PURIFIER
SPECIFICATIONS
Model HR900 Dimensions 16.3in(W) × 9.6in(D) × 23.6in(H)
Voltage AC 120 V / 60 Hz Weight 18.7lbs
Power Rate 90W Filter SKU Filter T / SKU: 1712-0093-00 &
Filter U / SKU: 1712-0094-00
Verified Room Size 300sq.ft.
The exterior, design, and product specifications may be changed without prior notice to improve product performance.
•Dedicated Call Center: ☎[phone]
•Website: www.winixamerica.com
Contact Winix for product
related inquiries and
customer service
To expedite service, please specify the model
name and number, the nature of the problem,
your contact information, and your address.
IMPORTANT PRECAUTIONS FOR USING YOUR AIR PURIFIER:
• Do not block the intake or outlet vents.
• Do not use near hot objects, such as a stove.
• Do not use where the unit may come into contact with steam.
• Do not use the unit on its side.
• Keep away from products that generate oily residue, such as a deep fryer.
• Do not use detergent to clean the unit.
• Do not operate without a filter.
• Do not wash and reuse the True HEPA Filter or the Carbon Filter.
• Hold the handle on the back of the unit to transport.
• Do not hold by the front panel.
• Do not stick any small objects into the air outlet vents or fan.
• The product warranty is printed on the back of this guide.
• This product is manufactured for use only in USA / CA.
• This product is suitable for 120 V only.
2610-0322-00 Rev.00