Winmate EL Series User manual

Please read these instructions carefully before using this product, and save this manual for future use.
EL-Series HMI
Freescale® Cortex® A9 i.MX6 Dual Core, 1 GHz
Android 6.0
Model No. W04FA3S-ELT1
W05FA3S-ELT1
W07FA3S-ELT1
W10FA3S-ELH2
W15FA3S-ELA4
User Manual
Document Version 1.3
Document Part No.9152111I1134

2
EL-Series HMI User Manual
Contents
Preface.................................................................................................................................................3
About This User Manual......................................................................................................................7
Chapter 1: Introduction.......................................................................................................................8
1.1 Introduction..................................................................................................................... 9
1.2 Product Features............................................................................................................. 9
1.3 Package Contents........................................................................................................... 9
1.4 Description of Parts....................................................................................................... 10
Chapter 2: Getting Started................................................................................................................15
2.1 Powering On................................................................................................................. 16
2.2 Connector Description and Pin Assignments................................................................. 17
Chapter 3: Mounting..........................................................................................................................19
3.1 Cable Mounting Considerations .................................................................................... 20
3.2 Safety Precautions........................................................................................................ 20
3.3 Mounting Guide............................................................................................................. 20
Chapter 4: Operating the Device ......................................................................................................25
4.1 Operating System ......................................................................................................... 26
4.2 Multi-Touch................................................................................................................... 26
4.3 System Settings............................................................................................................ 27
4.4 Ethernet........................................................................................................................ 29
4.5 Winmate® Home Manager (WHM)................................................................................ 32
Chapter 5: Software Installation.......................................................................................................37
5.1 Android Debug Bridge (ADB) Driver Installation............................................................ 38
5.2 Installing Android Debug Bridge (ADB) ......................................................................... 46
5.3 Downloading Image Tool............................................................................................... 47
5.4 OTA Update Guide........................................................................................................ 47
5.5 OS Image Update Guide............................................................................................... 51
Chapter 6: Technical Support...........................................................................................................52
6.1 Introduction................................................................................................................... 53
6.2 Problem Report Form................................................................................................- 53 -
Appendix A: Product Specifications................................................................................................54

3
EL-Series HMI User Manual
Preface
Copyright Notice
No part of this document may be reproduced, copied, translated, or transmitted in any form or by any
means, electronic or mechanical, for any purpose, without the prior written permission of the original
manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer
We reserve the right to make changes, without notice, to any product, including circuits and/or software
described or contained in this manual in order to improve design and/or performance. We assume no
responsibility or liability for the use of the described product(s) conveys no license or title under any
patent, copyright, or masks work rights to these products, and make no representations or warranties
that these products are free from patent, copyright, or mask work right infringement, unless otherwise
specified. Applications that are described in this manual are for illustration purposes only. We make no
representation or guarantee that such application will be suitable for the specified use without further
testing or modification.
Warranty
Our warranty guarantees that each of its products will be free from material and workmanship defects
for a period of one year from the invoice date. If the customer discovers a defect, we will, at his/her
option, repair or replace the defective product at no charge to the customer, provide it is returned during
the warranty period of one year, with transportation charges prepaid. The returned product must be
properly packaged in its original packaging to obtain warranty service. If the serial number and the
product shipping data differ by over 30 days, the in-warranty service will be made according to the
shipping date. In the serial numbers the third and fourth two digits give the year of manufacture, and the
fifth digit means the month (e. g., with A for October, B for November and C for December).
For example, the serial number 1W18Axxxxxxxx means October of year 2018.
Customer Service
We provide a service guide for any problem by the following steps: First, visit the website of our
distributor to find the update information about the product. Second, contact with your distributor, sales
representative, or our customer service center for technical support if you need additional assistance.
You may need the following information ready before you call:
Product serial number
Software (OS, version, application software, etc.)
Description of complete problem
The exact wording of any error messages
In addition, free technical support is available from our engineers every business day. We are always
ready to give advice on application requirements or specific information on the installation and
operation of any of our products.

4
EL-Series HMI User Manual
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful information or to alert you
to the potential for hardware damage or personal injury. These are Notes, Important, Cautions, and
Warnings. The following is an example of each type of advisory.
Note:
A note is used to emphasize helpful information
Important:
An important note indicates information that is important for you to know.
Caution/ Attention
A Caution alert indicates potential damage to hardware and explains how to avoid the
potential problem.
Une alerte d’attention indique un dommage possible à l’équipement et explique comment
éviter le problème potentiel.
Warning!/ Avertissement!
An Electrical Shock Warning indicates the potential harm from electrical hazards and how
to avoid the potential problem.
Un Avertissement de Choc Électrique indique le potentiel de chocs sur des emplacements
électriques et comment éviter ces problèmes.
Safety Information
Warning!/ Avertissement!
Always completely disconnect the power cord from your chassis whenever you work with
the hardware. Do not make connections while the power is on. Sensitive electronic
components can be damaged by sudden power surges. Only experienced electronics
personnel should open the PC chassis.
Toujours débrancher le cordon d’alimentation du chassis lorsque vous travaillez sur celui-
ci. Ne pas brancher de connections lorsque l’alimentation est présente. Des
composantes électroniques sensibles peuvent être endommagées par des sauts
d’alimentation. Seulement du personnel expérimenté devrait ouvrir ces chassis.
Caution/ Attention
Always ground yourself to remove any static charge before touching the CPU card.
Modern electronic devices are very sensitive to static electric charges. As a safety
precaution, use a grounding wrist strap at all times. Place all electronic components in
a static-dissipative surface or static-shielded bag when they are not in the chassis.
Toujours verifier votre mise à la terre afin d’éliminer toute charge statique avant de
toucher la carte CPU. Les équipements électroniques moderns sont très sensibles
aux décharges d’électricité statique. Toujours utiliser un bracelet de mise à la terre
comme précaution. Placer toutes les composantes électroniques sur une surface
conçue pour dissiper les charge, ou dans un sac anti-statique lorsqu’elles ne sont pas
dans le chassis.
Alternating Current Mise à le terre !
The Protective Conductor Terminal (Earth Ground) symbol indicates the potential risk of
serious electrical shock due to improper grounding.
Le symbole de Mise à Terre indique le risqué potential de choc électrique grave à la
terre incorrecte.

5
Preface
For your safety carefully read all the safety instructions before using the device. Keep this user manual
for future reference.
Always disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray
detergents for cleaning. Use a damp cloth.
For pluggable equipment, the power outlet must be installed near the equipment and must be
easily accessible.
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause
damage.
The openings on the enclosure are for air convection and to protect the equipment from
overheating.
Do not cover the openings.
Before connecting the equipment to the power outlet make sure the voltage of the power source is
correct.
Position the power cord so that people cannot step on it. Do not place anything over the power
cord.
If the equipment is not used for a long time, disconnect it from the power source to avoid damage
by transient over-voltage.
Never pour any liquid into an opening. This could cause fire or electrical shock.
Never open the equipment. For safety reasons, only qualified service personnel should open the
equipment.
All cautions and warnings on the equipment should be noted.
*Let service personnel to check the equipment in case any of the following problems
appear:
oThe power cord or plug is damaged.
oLiquid has penetrated into the equipment.
oThe equipment has been exposed to moisture.
oThe equipment does not work well or you cannot get it to work according to the
user manual.
oThe equipment has been dropped and damaged.
oThe equipment has obvious signs of breakage.
Do not leave this equipment in an uncontrolled environment where the storage temperature is
below -20°C (-4°F) or above 60°C (140°F). It may damage the equipment.
Caution/Attention
Use the recommended mounting apparatus to avoid risk of injury.
Utiliser l’appareil de fixation recommandé pour éliminer le risque de blessure.
Warning!/ Avertissement!
Only use the connection cords that come with the product. When in doubt, please
contact the manufacturer.
Utiliser seulement les cordons d’alimentation fournis avec le produit. Si vous
doutez de leur provenance, contactez le manufacturier.
Warning!/ Avertissement!
Always ground yourself against electrostatic damage to the device.
Toujours vérifier votre mise à la terre afin que l’équipement ne se décharge pas sur
vous.
Cover workstations with approved anti-static material. Use a wrist strap connected to a
work surface and properly grounded tools and equipment.
Use anti-static mats, heel straps, or air ionizer for added protection.

6
EL-Series HMI User Manual
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before inserting and removing connectors or test
equipment.
Keep the work area free of non-conductive materials, such as ordinary plastic assembly
aids and Styrofoam.
Use filed service tools, such as cutters, screwdrivers, and vacuum cleaners that are
conductive.
Always put drivers and PCB’s component side on anti-static foam.
Important Information
Federal Communications Commission Radio Frequency Interface Statement
This device complies with part 15 FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class "B" digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at him own expense.
EC Declaration of Conformity
This equipment is in conformity with the requirement of the following EU
legislations and harmonized standards. Product also complies with the
Council directions.
Electromagnetic Compatibility Directive (2014/30/EU)
EN55024: 2010 EN 55022: 2010 Class B
oIEC61000-4-2: 2009
oIEC61000-4-3: 2006+A1: 2007+A2: 2010
oIEC61000-4-4: 2012
oIEC61000-4-5: 2014
oIEC61000-4-6: 2013
oIEC61000-4-8: 2010
oIEC61000-4-11: 2004
EN55022: 2010/AC:2011
EN61000-3-2:2014
EN61000-3-3:2013
Low Voltage Directive (2014/35/EU)
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013

7
About This User Manual
About This User Manual
This User Manual provides information about using the Winmate® EL-Series HMI. This User Manual
applies to the EL-Series HMI –W04FA3S-ELT1, W07FA3S-ELT1, W10FA3S-ELH2, and W15FA3S-
ELA2.
The documentation set for the EL-Series HMI with Freescale® Cortex® A9 i.MX6 Dual Core provides
information for specific user needs, and includes:
EL-Series HMI User Manual –contains detailed description on how to use the HMI device, its
components and features.
EL-Series HMI Quick Start Guide - describes how to get the HMI up and running.
Note:
Some pictures in this guide are samples and can differ from actual
product.
Document Revision History
Version
Date
Note
1.0
25-Jul-2018
Initial document release
1.1
20-Feb-2019
Add 5.6” HMI device.
1.2
20-Mar-2019
Revise specifications
1.3
10-Sep-2019
Revise cutout dimensions

8
EL-Series HMI User Manual
Chapter 1: Introduction
This chapter gives you product overview, describes features and
hardware specification. You will find all accessories that come
with the HMI in the packing list. Mechanical dimensions and
drawings included in this chapter.

9
Chapter 1: Introduction
1.1 Introduction
Congratulations on purchasing Winmate® EL-Series HMI. Winmate continues developing new generation
of Human Machine Interfaces for Industry 4.0 and Internet of Things (IoT). Our EL-Series HMI runs on
Android 6.0 operating system that allows installing the latest applications (APPs). There is one USB 2.0
onboard to connect mouse or keyboard, Micro USB OTG for system updates. System memory LPDDR3 of
1 GB ensures stable operation of applications.
With mounting clips for panel mounting there is no need to drill holes in a fixture. This saves you the time
for mounting and guarantee aesthetic look of the wall after the unit gets removed.
1.2 Product Features
Winmate® EL-Series HMI features:
4.3/ 5.6/ 7/ 10.1/ 15.6-inch widescreen panel
Freescale® Cortex® A9 i.MX6 Dual Core, 1 GHz
Android 6.0 operating system
Projected Capacitive (P-CAP) Multi-Touch
Fanless cooling system and ultra-low power consumption
Front IP65 water and dust proof, rear IP22
Mounting clips for quick Installation
Light design for machine automation, smart factory and IoT applications
1.3 Package Contents
Carefully remove the box and unpack your device. Package content may vary based on your order. Please
check if all the items listed below are inside your package. If any of these items are missing or damaged
contact us immediately.
Standard factory shipment list:
HMI Device
Varies by product
specifications
Quick Start Guide
(Hardcopy)
Part No.9152111I1135
Driver CD & User
Manual (Digital Copy)
Varies by product
specifications
Mounting Clip & Screw
4.3” HMI - 4 pcs, 5.6” HMI - 6 pcs,
7” –7 pcs, 10.1” HMI – 8 pcs, 15.6”
HMI –10 pcs
Part No. 82111E240400
AC Adapter
(12V/ 50W)
Part No. 922D050W12VA
Power Cord
Varies by country
3 pin Terminal Block
Part No.
94J602G020K0

10
EL-Series HMI User Manual
1.4 Description of Parts
This section describes appearance, connectors’ layout and mechanical dimensions of EL-Series HMI.
Notice that this is a simplified drawing and some components are not marked in detail. Please contact our
sales representative if you need further product information.
EL-Series HMI 4.3” Unit: mm
Dimensions : 121.5 x 82.05 x 42.2
№
Description
№
Description
❶
USB 2.0
❺
USB OTG
❷
RS485
❻
Power Terminal Block
❸
Reset Button
❼
LED Indicator
❹
RJ45/ LAN

11
Chapter 1: Introduction
EL-Series HMI 5.6”Unit: mm
Dimensions : 158.7 x 116.3 x 51
№
Description
№
Description
❶
USB 2.0
❺
USB OTG
❷
RS485
❻
Power Terminal Block
❸
Reset Button
❼
LED Indicator
❹
RJ45/ LAN

12
EL-Series HMI User Manual
EL-Series HMI 7” Unit: mm
Dimensions : 184.94 x 127.7 x 44.9
№
Description
№
Description
❶
USB 2.0
❺
Power Terminal Block
❷
RS485
❻
LED Indicator
❸
RJ45/ LAN
❼
Reset Button
❹
USB OTG

13
Chapter 1: Introduction
EL-Series HMI 10.1” Unit: mm
Dimensions : 267.42 x 182.14 x 57.6
№
Description
№
Description
❶
USB 2.0
❺
Power Terminal Block
❷
RS485
❻
LED Indicator
❸
RJ45/ LAN
❼
Reset Button
❹
USB OTG

14
EL-Series HMI User Manual
EL-Series HMI 15.6” Unit: mm
Dimensions : 387.6 x 257.7 x 52.5
№
Description
№
Description
❶
USB 2.0
❺
Power Terminal Block
❷
RS485
❻
LED Indicator
❸
RJ45/ LAN
❼
Reset Button
❹
USB OTG

15
Chapter 2: Getting Started
Chapter 2: Getting Started
This chapter tells you important information on power supply, adapter
and precautions tips. Pay attention to power considerations.

16
EL-Series HMI User Manual
2.1 Powering On
2.1.1 AC Adapter Components
Safety Precautions:
Do not use the adapter in a high moisture environment
Never touch the adapter with wet hands or foot
Allow adequate ventilation around adapter while using
Do not cover the adapter with paper or other objects that will reduce cooling
Do not use the adapter while it is inside a carrying case
Do not use the adapter if the cord is damaged
There are NO serviceable parts inside
Replace the unit if it is damaged or exposed to excess moisture
While using the AC Adapter always:
Plug-in the power cord to easy accessible AC outlet
Plug-in the AC adapter to a grounded outlet
2.1.2 Power Considerations
The HMI device operates on external DC power. Use the AC adapter included in the package.
Caution/ Attention
Use only the AC adapter included in your package
(Rating: Output 12 V/ 6.6A). Using other AC adapters may damage the device.
Utiliser seulement le convertisseur AC inclu avec votre appareil (Puissance: Sortie 12 V/
6.6A). Utiliser d’autres convertisseurs pourraient endommager l’appareil.
AC Adapter
Power Cord
2 Pin Terminal Block to
DC Jack
Alternating Current/ Mise à le terre !
This product must be grounded. Use only a grounded AC outlet. Install the additional PE
ground wire if the local installation regulations require it.
*If you do not use a grounded outlet while using the device, you may notice an electrical
tingling sensation when the palms of your hands touch the device.
[FR]Ce produit doit être mis à la terre. Utiliser seulement un cordon d’alimentation avec
mise à la terre. Si les règlements locaux le requiert, installer des câbles de mise à la
terre supplémentaires.
*Si vous n’utiliser pas une prise d’alimentation avec mise à la terre, vous pourriez
remarquer une sensation de picotement électrique quand la paume de vos mains touche
à l’appareil.

17
Chapter 2: Getting Started
2.1.3 Connecting the Power
Installation Instruction:
1. Connect a 3-pin terminal block to the HMI connector.
2. Connect the other side of the terminal block to the AC adapter.
3. Connect the AC adapter to the power cord.
4. Plug in the power cord to a working AC wall outlet. The device will boot automatically.
2.2 Connector Description and Pin Assignments
2.2.1 Power Input Connector
The DC power source input of the panel PC is a 2 pin terminal block connector that supports 12-24V DC
power input, maximum current 3.3A.
Pin assignment and connector description of terminal block connector
Note:
Based on the model, terminal block connector may be located either on the bottom or
on the rear side of the HMI device.
Note:
Power cords vary in appearance by region and country.
Voltage
Minimum Voltage 9V
Maximum Voltage 24V
Maximum Current 3.3A

18
EL-Series HMI User Manual
2.2.2 Serial Port Connector
The HMI device has one RS-485 serial port connector to connect your device to external devices.
Pin assignment and connector description of serial port connector
2.2.3 Ethernet Connector
The HMI device supports one RJ45 10/100/1000 Mbps Ethernet interface for connecting to the internet.
Pin assignment and connector description of RJ45 connector
2.2.4 USB 2.0 Connector
Use USB A Type (USB 2.0) connector to connect your device to other USB 2.0 compatible devices.
Pin assignment and connector description of USB 2.0 connector
2.2.5 USB OTG Connector
Use USB OTG connector to connect the panel PC to other USB On-The-Go compliant devices such as
flash drives, digital cameras, mice or keyboards. Use USB OTG cable to install software on the panel PC.
Pin assignment and connector description of USB UTG connector
Refer to Ch.5 of this user manual for more details on how to install software
Pin №
Signal Name
1
D+
2
D-
3
GND
Pin №
Signal Name
Pin №
Signal Name
1
TX1+
2
TX1-
3
TX2+
4
TX2-
5
TX3+
6
TX3-
7
TX4+
8
TX4-
Pin №
Signal Name
Pin №
Signal Name
1
+5V
2
USB_D-
3
USB_D+
4
GND
Pin №
Signal Name
Pin №
Signal Name
1
+5V
2
USB_OTG_D-
3
USB_OTG_D+
4
USB_OTG_ID
5
GND

19
Chapter 3: Mounting
Chapter 3: Mounting
This chapter provides mounting guide for all available mounting
options. Pay attention to cautions and warning to avoid any
damages.

20
EL-Series HMI User Manual
3.1 Cable Mounting Considerations
For a nice look and safe installation, make sure cables are neatly hidden behind the HMI device. Refer
to Chapter 2, section 2.1 for the cable installation instruction.
Caution/ Attention
Observe all local installation requirements for connection cable type and protection level.
Suivre tous les règlements locaux d’installations, de câblage et niveaux de protection.
Caution/ Attention
Turn off the device and disconnect other peripherals before installation.
Éteindre l’appareil et débrancher tous les périphériques avant l’installation.
3.2 Safety Precautions
Observe the following common safety precautions before installing any electronic device:
• Use separate, non-intersecting paths to route power and networking wires. If power wiring and
device wiring paths must be crossed make sure the wires are perpendicular at the intersection
point.
• Keep the wires separated according to the interface. Wires that share similar electrical
characteristics must be bundled together.
• Do not bundle input wiring with output wiring. Keep them separate.
When necessary, it is strongly advised that you label wiring to all devices in the system.
3.3 Mounting Guide
EL-series HMI devices come with different mounting options suitable for most of the industrial and
commercial applications. The main mounting approach is rear mount - very user-friendly in terms of
installation. Refer to sub-sections below for more details.
Caution/ Attention
Follow mounting instructions and use recommended mounting hardware to avoid the risk
of injury.
Suivez les instructions de montage et d'utilisation recommandé le matériel de montage
pour éviter le risque de blessure.
Alternating Current / Mise à le terre !
To prevent electrical shock, the Safety Ground location on the rear must be bonded to
the local earth ground through a minimum 12 AWG wire as short as possible
Pour éviter les chocs électriques, l’emplacement de la prise terre à l’arrière doit être lié
à terre locale, à travers un 12 AWG minimum et aussi court que possible.