Wittkopp BlueCam greendot User manual

www.carl-wittkopp.com
Operating Instructions
Changing users
BlueCamgreendot

2 Operating Instructions No. 9999-084-020.06.2011
Operating Instructions
BlueCamgreendot
Table of contents Page
1 General instructions 3
2 Locking 4
3 Opening with the user code 4
4 Opening after 4 wrong code entries 5
5 Opening with the 1st master code 5
6 Opening with the 2nd master code 6
7 Changing the 1st and 2nd master code 7
8 Power supply and battery change 8
Legend
LED flashes green
LED is permanently green
LED flashes red
LED is permanently red
Tone signal
R
G
G
R

© Carl Wittkopp GmbH - errors and omissions excepted

20.06.2011Operating Instructions No. 9999-084-0 3
Operating Instructions BlueCamgreendot
1 General instructions
• Please read the operating instructions carefully, before activating
the lock.
• The lock is supplied with the following factory codes:
- User factory code: 1-2-3-4
- 1st master factory code: 1-2-3-4-5-6
- 2nd master factory code: 6-5-4-3-2-1
For your security, change the factory codes immediately.
• Change codes only if the safe is opened and lock is in closed position.
• In case of changing a master code, the lock has to be opened with the
corresponding master code before.
• Do not use any personal data like birthdays or telephone numbers as new
codes.
• If the lock is not opened or closed within 3 seconds after the ON-button is
pressed, the electronics will shut down. Press the ON-button again and repeat
the operation.
• If the time has been exceeded for entering a new code, the electronics will shut
down. The old code remains valid.
• Every correct code entry at opening or closing is conrmed by a tone signal
and a green LED will flash. These signals are not described in the following
instructions.
• Do not use force.
• Do not open the lock case. Otherwise you endanger the function of the lock
and you lose any warranty claims.

4 Operating Instructions No. 9999-084-020.06.2011
Operating Instructions
BlueCamgreendot
2 Locking
At any time upon locking a 4-digit user code can be chosen.
1. Press the ON-button. G R

2. Enter a 4-digit user code within 10 seconds. G3 seconds
3. Turn the handle within 3 seconds. The lock is opened. R

4. After locking always check if the door is blocked.
If a wrong user code has been entered, a tone signal sounds several times and
the LED flashes red. Press the ON-button after the LED has lapsed and enter your
code again.
3 Opening with the user code
The previously selected 4-digit user code must be entered to enable
opening.
1. Press the ON-button. G R

2. Enter a 4-digit user code within 10 seconds. G3 seconds
5 Turn the handle within 3 seconds. The lock is opened. R


20.06.2011Operating Instructions No. 9999-084-0 5
Operating Instructions BlueCamgreendot
If a wrong code has been entered in step 4, the lock is blocked for another
30 seconds.
4 Opening after 4 wrong code entries
1.
After 4 wrong code entries the lock is blocked for 30
seconds. During this time it is not possible to enter a
code.
R
2. At the end of the blocked time the red LED goes out
and a tone signal sounds several times. 
3. Press the ON-button. G R

4. Enter a 4-digit user code within 10 seconds. 3 seconds
5. Turn the handle within 3 seconds and the lock opens.
G
5 Opening with the 1st master code
The 1st master code is only necessary if the lock is locked and the user code is not
known.
By entering the 1st master code the user code is deleted.
1. Keep the ON-button pressed until the LED shines
permanently green. G
2. Start to enter the 1st master code within 5 seconds. 10 seconds
3. Turn the handle within 3 seconds. The lock opens
and the user code is deleted.
4. After the LED goes out, the lock is ready for use gain.
R

6 Operating Instructions No. 9999-084-020.06.2011
Operating Instructions
BlueCamgreendot
In case the user code does not have to be preserved, enter a new 4-digit user
code for locking (see 2). Now the lock can be opened by the new selected user
code (see 3).
6 Opening with the 2nd master code
The 2nd master code is only necessary if the lock is locked and the user code is
not available.
By entering the 2nd master code the user code is still valid.
1. Keep the ON-button pressed until the LED lights up
permanently green. G
2. Start to enter the 2nd master code within 5 seconds. 10 seconds
3. Turn the handle within 3 seconds. The lock is opened.
4. To keep the user code, keep the ON-button pressed
until the LED shines permanently green. 10 seconds
5.
Enter the 2nd master code and turn the handle within
3 seconds. The lock is closed and can be opened
with the user code.
R
G

20.06.2011Operating Instructions No. 9999-084-0 7
Operating Instructions BlueCamgreendot
If the time has been exceeded for entering the new code in step 3, the electronics
will shut down. The old code remains valid.
1. Keep the ON-button pressed until the LED shines
permanently green. G
2. Start within 5 seconds to enter the master code. 10 seconds
3. Enter a new 6-digit master code. goes out
4. The new master code is accepted.
5. After programming the new master code, the lock
can be operated with a new user code.
R
7 Changing the 1st and 2nd master code
The lock can be operated with one or two master codes.
One master code:
1st master code and 2nd master have to be the same code. During reprogram-
ming the 1st master code will be deleted.
ATTENTION! After deletion, the 1st master code cannot be regenerated!
From now see 6: Opening with 2nd master code.
Having only one master code is not recommended!
Two master codes:
1st master code and 2nd master code have to be different.
During reprogramming of the master code the lock has to be closed.
G


8 Operating Instructions No. 9999-084-020.06.2011
Operating Instructions
BlueCamgreendot
8 Power supply and battery change
The lock is operated with a 9 volt alkaline battery. We recommend using a battery
with reduced heavy metal concentration.
If the LED flashes red after pressing the ON-button, the battery voltage is low.
Change the battery as soon as possible.
If the LED ashes red ve times and a triple tone signal sounds after pressing the
ON-button, the code cannot be entered because of low voltage. After the rst
code number has been entered, the LED goes out. Change the battery immedia-
tely.
To change the battery, the M4 screw and the M18 nut at the back of the lock has
to be loosened. Lift the battery cover at the lock case and change the battery.
Replace the battery cover again and fasten nut and screw.
If the battery is so low that a code entry is not possible anymore, the lock can be
supplied with power from outside. Place a 9 volt block battery at the power termi-
nals of the input unit (see Fig. 1) and open the lock as described in point 3.
Always dispose used batteries in an environmentally friendly way. Trade Collec-
ting points or public waste management authorities take back waste batteries free
of charge.
Fig. 1: Emergency power supply
Place battery for emergency power supply here