WMF 1200F Instructions for use

µ
WMF coffeemachines
WMF 1200 F planning information
http://www.wmf-kaffeemaschinen.de/fachplaner
WMF Group GmbH | Eberhardstraße 35 |73312 Geislingen (Steige)
Optional: cut-out for
grounds through counter
Optional: cut-out 60x80 mm for lines and hoses
(water, waste water, power) 3kW min. Ø 50
On site
On site
3x1,5mm2
Length 1m
(Angle valve)
Optional: vending unit
Coin Checker 105 mm
Optional feet
(60mm/
100 mm
Optional: pipe for grounds
disposal 70 x 120 x 250
mm (extension with
second pipe possible)
(incl. Cover cap)
Optional: jug tray and
thermos container 2.4L
(Optional: jug tray right side / thermos container and vending unit not combinable)
With automatic post brewing function
Jug tray and thermos
container 2,4 liters
Optional feet
(60mm/
100 mm

µ
WMF coffeemachines
WMF 1200 F planning information
Conditions for usage and installation
Any necessary on-site preparatory work for electricity, water and drainage connections at the customer‘s premises
is to be arranged by the machine owner / operator. The work must be carried out
by authorised installation technicians in compliance with general, country-specific and local regulations. The
WMF service engineers may only connect the coffee machine to existing prepared
connection points. WMF Service is neither authorised nor responsible for carrying out any on-site installation
work prior to connection. The potential equalisation terminal is installed by WMF Service if needed
Dimensions
and empty
weight
Width
Width with brew arm
Height
Depth
Clearance heights
Weight
324 mm (with jug tray 507; automatic post brewing function 535 mm)
372 mm
682 mm
599 mm
60 –165 mm
Approx. 33 - 38 kg (depending on the model)
Water supply Water supply line
Inlet temperature
Water drain tube
(optional)
3/8 inch hose connector with mains tap, and filter
with 0.08 mm mesh size, on site. At least 0.2 MPa (2 bar) flow pressure
at 2 l/min (standard). Maximum 0.6 MPa (6 bar).
Maximum 35 °C.
Tube a minimum of DN 19, minimum downward slope
of 2 cm/m
For use at
altitude
above NN
<2000m
Electrical
data
Nominal power
rating
3.1 –3.7 kW
Power supply 220–240 V 50 / 60 Hz (1 / N / PE)
Degree of protection IP X0
Protection Class I
Installation
Clearance
For operating, service, and safety reasons the machine should be installed with a clearance from
the building or non-WMF components of not less than 50 mm at the sides and 60 mm at the
back. A minimum working space of 800 mm in front of the coffee machine is recommended.
Clearance of at least 200 mm above the product hopper is recommended. The height of the
installation surface above the floor is at least 850 mm. If the coffee machine connections are to
be run downwards through the counter, please make space for the lines, which can reduce the
usable space below the machine. Additional space for grounds through counter need to be
considered on site if necessary. If the coffee machine is operated with a water filter the
additional space under the machine depending on the fitler size has to be considered. For
further information see filter instructions.
Ventilation If ventilation possibility is limited sufficient ventilation need to be provided e.g machine on feet
extension, active ventilation, additional ventilation slots/ openings in counter area. Ventilation
slots must not be covered. Under certain circumstances a forced ventilation on site is necessary
to ensure heat dissipation.
Installation
surface /
water spray
The device must be placed and leveled on a horizontal, sturdy, water-resistant, and heatproof
base. The device must not be cleaned using a water jet. The device must be installed where it is
protected against water spray. The device must not be located on a surface that is sprayed or
cleaned with a water hose, steam jets, steam cleaner, or similar devices.
http://www.wmf-kaffeemaschinen.de/fachplaner
WMF Group GmbH | Eberhardstraße 35 |73312 Geislingen (Steige)

µ
WMF coffeemachines
WMF 1200 F planning information
Electrical
connection
These specifications for the electrical connection and the standards quoted apply for
connecting the coffee machine in EU countries. It may be necessary to also observe additional
country-specific regulations. Outside the EU countries acceptance of the standards quoted is
to be checked by the legal entity or natural person who wishes to use the coffee machine.
The local power supply must be constructed according to the currently valid IEC 364 (DIN VDE
0100). An isolated ground socket or a country-specific single-phase socket for single-phase
connection, or a 5-pole CEE / CEKON socket per EN 60309 or a country-specific multi-pole
socket for a three-phase connection, must be available near the machine. The sockets are part
of the customer‘s on-site installation.
The mains cable must not come into contact with hot surfaces. If the mains cable for this
device is damaged then it must be replaced by our service personnel or a similarly qualified
person, in order to prevent hazards.
In order to avoid possible faults from arising on our shielded data lines due to potential
equalisation currents between the devices, an additional potential equalisation unit should be
planned for devices connected to the vending system. (See EN 60309)
Water supply
and drainage
The water supply must be located close to the machine (max. distance 800 mm). An anytime
easily accessible and sufficiently dimensioned water tap (preferably ball tap) as well as a dirt
filter with mesh size 0,080 mm must be installed below the counter in the water supply.
For connection from below through the counter a cut-out must be made in the hatched area
on-site according to drawing (see top view).
For drinking water with carbonate hardness above 5°dKH (carbonate hardness), a WMF water
filter should be fitted upstream.
If the coffee machine is connected to a drain connection, a funnel siphon must be installed in
the drain pipe.
Please observe that the free drain (funnel siphon with sheet metal angle) is fitted vertically.
This means that it must always be vertical to the water back pressure level that is reached. It
must be fitted in a way that the given gradient of the drain hoses (2%) is observed.
Additionally, the free drain must always be below the drains of the coffee machine and above
the actual drain pipe connections (HT40, HT50 or similar) with respect to its height.
To a funnel siphon with sheet metal angle max. two coffee machines with DN19 hose and
black silicone fabric hose should be connected. Other devices (dishwasher, sink etc.) should be
installed elsewhere.
The free drain incl. hoses must not be exposed to heavy tensile, pressure or torsional load.
Hereby, damage might be caused at the mechanical components of the free drain.
Consequently, its usability may get lost.
The on-site preliminary works for the drainage connection must be commissioned by the
operator of the machine. They must be carried out by concession plumbers in compliance
with the prevailing, national as well as local regulations.
The following drawings serve to illustrate the drains and do not include any other
connections, such as power or water infeed!
http://www.wmf-kaffeemaschinen.de/fachplaner
WMF Group GmbH | Eberhardstraße 35 |73312 Geislingen (Steige)

µ
WMF coffeemachines
WMF 1200 F planning information
Miscellaneous Ambient
temperature
+5 °C to maximum +35 °C
(empty the water system in case of frost).
Maximum
humidity
80 % relative humidity without condensation. Do not use device outdoors.
Heat
dissipation
0.035 kWh/h standby mode
3.1 –3,7 kWh/h maximum use
Continuous
sound
pressure level
(Lpa)
< 70 dB(A)
For more information as the instruction manual , safety data sheets and certificates , see:
http://www.servicecenter.wmf.de/
All information refers to coffee machines/ equipment as standard version. Individual solutions can differ from the
standard version.
http://www.wmf-kaffeemaschinen.de/fachplaner
WMF Group GmbH | Eberhardstraße 35 |73312 Geislingen (Steige)