Wood Stone 8645 User manual

Fire Deck 8645
Installation and Operation Manual
PG 7 OF 32
M0039.12 DECEMBER 2019
An ongoing program of product improvement may
require us to change specifications without notice.
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
TOLL FREE 800.988.8103
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
woodstone-corp.com
UNLOADING & MOVING THE OVEN
CAUTION HOT PRUDENCE CHAUD
USING A FORKLIFT.
The Wood Stone Fire Deck 8645 weighs approximately 4,350 lbs� and is top-heavy�
Use a forklift with adequate fork lengths and lifting capacity� When using a forklift, always use the forklift pockets� Lifting the oven
any other way with a forklift may result in damage� Use extreme caution and make sure that the forks extend all the way through the
pockets provided� Fork length must be at least 6' long� If it is necessary to approach the oven from the front, be sure the mast does
not contact the mantle (shelf)�
There are fork pockets at the front and sides of the oven� Note: Forklift capacity is different if lifting from the front/rear or the sides�
Once the oven is on a smooth, flat, level floor it can be rolled on its optional heavy-duty, temporary shipping Casters (details next
page)�
USING A PALLET JACK.
The oven may also be moved with a Pallet Jack using the front or rear fork pockets only� Once the oven is on a smooth, flat, level
floor it can be rolled to its final position� DO NOT ATTEMPT TO MANUALLY ROLL THE OVEN UP OR DOWN A RAMP OR INCLINE.
Do not position yourself between the moving oven and an immovable object or surface such as a wall or door frame�
DO NOT TURN THE OVEN ON ITS SIDE!.
Moving a Wood Stone oven can present interesting challenges to even the most
experienced riggers� Make sure to secure the proper equipment and make safety
your first priority� Please don’t hesitate to call the factory for technical support�
USING A CRANE.
If you are planning to use a crane to unload the oven,
specify a flatbed truck delivery.
Use the pickeyes provided on the sides of the oven to lift the
oven with a crane� The spreader bar should be of a sufficient
length to keep the sling from contacting the oven, and oriented
as shown in fig� 1�
DELIVERY NOTE.
The customer will receive an Oven Shipping Notification when
the oven leaves the Wood Stone factory� This will include a
PRO# and a trucking company contact number� Wood Stone
recommends that you confirm the delivery date/time with the
trucking company before committing to heavy equipment and/
or labor� Our goal is a smooth and safe delivery�
Pickeye Capacity
per Beam
4,000 lbs
LOAD
Orient Spreader Bar
as shown in fig. 1
50°MIN Angle
fig. 1
Pickeye
Beam
Front Forklift / Pallet Jack Pockets Side Forklift Pockets
Minimum Required
Forklift Capacities
6' FORKS MINIMUM
Model
Lifting from
Front or Rear
Lifting from
Sides
FD-8645 8,000 lbs 9,000 lbs
WARNING
Use caution
near mantle

Fire Deck 8645
Installation and Operation Manual
PG 8 OF 32
M0039.12 DECEMBER 2019
OPTIONAL TEMP CASTER INSTALL
INSTRUCTIONS FOR INSTALLING AND REMOVING OPTIONAL OVEN CASTERS
The Fire Deck 8645 weighs 4,350 lbs.
Do not attempt to move the oven over any type of grade or sloped surface when using the Casters or Pallet Jack.
WARNING: Failure to follow these instructions may result in severe injury or death. BE SAFE.
If you have any questions call Wood Stone at 800.988.8103.
NOTE: The casters will add 3" to the total height of the oven, for a total of 80-1/4".
The 3-3/4" Vent Shield on top can be removed temporarily if necessary.
Shipping Casters are for moving the oven only. THEY MUST BE REMOVED ONCE THE OVEN IS IN PLACE.
1 Use a forklift (or pallet jack) to raise the oven
using the front or rear forklift pockets�
3Once at final destination, use two scissor jacks (or
pallet jack) to lift the one side of the oven by placing
one jack under each caster assembly�
Raise the oven just high enough so the wheels clear
the floor�
Unbolt each Caster and remove it�
Note: Casters are for moving oven only� They must
be removed once the oven is in place�
4Lower the oven back to the ground�
Remove the Self-Drilling Screw and slide the rest of
the Caster Assembly out of the fork pocket�
Install Fork Pocket Covers�
Repeat steps 3and 4for the other side of the oven�
This oven is designed to be sealed to the floor upon
installation using a silicone sealant acceptable to the
local health official� See the Placing & Installation
section of this manual for additional information�
Caster Bolts
2 Insert a Caster Assembly into each of the side
fork pockets and secure it to the oven with a
Self-Drilling Screw and washer�
Install the screw through the Mounting Tab�
Once the Caster Assemblies are installed, lower
the oven�
It may then be rolled over a smooth flat
surface to its final destination�
Self-Drilling Screw
& Washer through
Mounting Tab

Fire Deck 8645
Installation and Operation Manual
PG 9 OF 32
M0039.12 DECEMBER 2019
PLACING & INSTALLATION
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
REAR FORK POCKETS
Pocket covers
arrive
fastened in
temporary UP
position.
Unfasten, lower
over each fork
pocket, and
refasten.
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
GAS INLET SIDE FORK POCKETS
Unfasten,
place one cover
over each fork
pocket, and
refasten.
Two pocket covers
will arrive fastened in
temporary UP
position above front-
most fork pocket.
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTIONINSTALLER
ForkPocket Cover
MUSTbe installed
overpocket for oven
tooperate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
L1217
ATTENTION INSTALLER
Fork Pocket Cover
MUST be installed
over pocket for oven
to operate properly.
NON-GAS INLET SIDE FORK POCKETS
Pocket covers
arrive
fastened in
temporary UP
position.
Unfasten, lower
over each fork
pocket, and
refasten.
Note: Additional
Tek screws
supplied in
hardware kit.
• •• • ••••
ÜÜ
• •• •
ÜÜÜÜ
• •• • ••••
ÜÜ
FORK POCKET
COVER
INSTALLATION
Fork pocket covers
(Both sides & rear)
Fork pocket covers
(Both sides & rear)
Stainless Steel Toe Kick
PLACING THE OVEN
The oven must be installed on a flat level surface� The weight of the oven is carried by the full perimeter of the oven stand� If it is
necessary to shim the oven for leveling purposes, it is critical that the shim material be metal, and that the shims are installed in such
a way that the full perimeter of the stand is solidly supported� Any gaps created by shimming between the oven and the floor must be
sealed (using a silicone sealant acceptable to the local health official) to prevent airflow issues beneath the oven� Failure to solidly
support the full perimeter of the oven stand can result in costly damage to the oven and will void the warranty.
The floor design and construction must be adequate to handle the weight of the oven�
See woodstone-corp.com for floor loading information�
TOE KICK AND FORK POCKET COVERS
Once the oven is in place, the Toe Kick must be installed along the front, and the Fork Pockets on the sides and back of the oven using
the screws provided� The area under the oven must be enclosed in order to prevent pests from entering this space and to prevent air
flow issues which can detrimentally effect burner operation�
FACADE READY OVENS: If the lower front of the oven is shipped facade ready, the toe kick will not be included� Instead, fork pocket
covers and pre-cut blocks of cement board to cover the pocket covers will be included�
If the sides and/or rear of the oven is shipped facade ready, the Fork Pocket Covers will not be included� Pre-cut blocks of cement
board or other facade material will be shipped instead of the Fork Pocket Covers� The blocks must be inserted into the fork pockets
before the oven facade is put in place�