woodmizer CookieMizer CMJ User manual

Your Wood-Mizer Account
For contact information, sales, service, parts, and additional
manuals, sign into your account on https://woodmizer.com.
Safety
Safety Symbols
The following symbols and signal words call your attention to
instructions concerning your personal safety. Be sure to observe
and follow these instructions.
DANGER! indicates an imminently hazardous situation
which, if not avoided, will result in serious injury or
death.
WARNING! suggests a potentially hazardous situation
which, if not avoided, could result in serious injury or
death.
CAUTION! refers to potentially hazardous situations
which, if not avoided, may result in minor or moderate
injury or damage to equipment.
NOTICE indicates vital information.
Safety Instructions
OWNER/OPERATOR'S RESPONSIBILITY
NOTICE It is the owner/operator’s responsibility
and not Wood-Mizer LLC to ensure all operators
are properly trained and informed of all safety
protocols. Owner/Operators are responsible for
following all safety procedures when operating and
performing maintenance to the equipment.
OBSERVE ALL SAFETY INSTRUCTIONS
NOTICE Read the entire Operator's Manual of your
mill before operating this attachment.
• Note all safety warnings throughout all manuals and
those posted on the machine.
• Be able to access this manual at all times while
operating this equipment.
• Only persons who have read and understood the mill’s
entire operator's manual should operate this equipment.
• This equipment is not intended for use by or around
children.
HEAVY MATERIAL
WARNING! .Use two-person lift for
handling the CookieMizer
WEAR SAFETY CLOTHING
WARNING! Always wear eye, ear, and foot protection
when operating or servicing the CookieMizer.
Some woods require respiration protection when
operating. It is the operator’s responsibility to know
which woods require respiration protection.
KEEP WORK AREA CLEAN
WARNING! Maintain a clean and clear path for all
necessary movement.
DISPOSE OF BY-PRODUCTS PROPERLY
NOTICE Always properly dispose of all by-products,
including sawdust and other debris, according to local
ordinances.
KEEP PERSONS AWAY
WARNING! Always be sure the cutting path is clear
before starting the motor.
Keep all persons out of the path of moving equipment.
KEEP HANDS AWAY
DANGER! Keep hands, feet, and other objects away
from log when operating the CookieMizer.
WARNING! Turn off the motor whenever the mill is not
cutting.
The image to the right shows the base model of the
CookieMizer. Read the proper mounting instructions
for your application prior to operating the machine.
Model CMJ
Quick Start Guide
Form #2100
CookieMizer

KEEP SAFETY LABELS IN GOOD CONDITION
CAUTION! All safety decals must be clean and
readable. Replace all damaged safety decals to
prevent personal injury or damage to the equipment.
Contact your Customer Service Representative to
order more decals.
If replacing a component which has a safety decal
affixed to it, ensure the new component also has the
safety decal affixed.
WORKING WITH HEAVY LOGS
WARNING! Ensure material is clamped securely
before processing.
Assembly
NOTICE Ensure you are referencing the mounting
instructions for your mill.
Mounting for LX25 or LX55 Wood-Mizer mills
Installation Kit: 123418
STEP 1: Remove the center log clamp
Retain all parts and hardware for reinstallation after cookie cutting
is finished.
STEP 2: Assemble the mounting brackets on the center
bed rails with 3/8" fasteners as shown here.
STEP 3: Mount the CookieMizer with 5/16" fasteners as
shown here.
Ensure the minimum cut indicator is toward the blade.
Mounting for LX150
Installation Kit: 123435
STEP 1: Lower the side supports.
STEP 2: Assemble the mounting brackets on the center
bed rails with 3/8" fasteners as shown here.
STEP 3: Mount the CookieMizer with 5/16" fasteners as
shown here.
Ensure the minimum cut indicator is toward the blade.
Mounting for LT15
Installation Kit: 123437
STEP 1: Lower the side supports.
STEP 2: Set the CookieMizer on the center bed rails with
the shortest span, oriented as shown here.
Ensure the minimum cut indicator is toward the blade.
STEP 3: Place the flat mounting plates on the inside of the
CookieMizer at the outermost slots.
STEP 4: Align the lower mount weldment to secure the
plate and the CookieMizer to the bed rail.
Note
orientation
Toward blade
Toward blade
1 inch
minimum
Toward blade

NOTE: Use the longer bolts that come with the mounting kit.
Mounting for LT28 through LT70 and LX450
Installation Kit: 123437
STEP 1: Lower the side supports and/or log clamps.
STEP 2: Set the CookieMizer on the center bed rails ori-
ented as shown here.
Your mill may vary from this illustration according to the model
and options you own.
STEP 3: Place the flat mounting plates on the inside of the
CookieMizer at the outermost slots.
If there is interference with the mounts, use the closest slot to the
outside as possible. The CookieMizer may also be positioned
closer to the center of the bed rails.
STEP 4: Align and fasten the lower mount weldment to
secure the plate and the CookieMizer to the bed rail.
NOTE: Use the shorter bolts that come with the mounting kit.
Mounting for all other mills
Installation Kit: 123441
Wood-Mizer provides generic brackets for all mills not listed here.
It is up to the customer to provide 3/8" bolts for their bed rails and
drill appropriate mounting holes. It is the customer’s responsibility
to ensure the CookieMizer is secure on the mill.
STEP 1: Ensure that the CookieMizer is level to the log bed
and the minimum cut indicator is toward the blade.
STEP 2: Loosely mount the brackets to the bottom of the
CookieMizer at the outermost slots.
If there is interference with the mounts, use the closest slot to the
outside as possible.
STEP 3: Use the mounting brackets as templates to drill
holes for 3/8" bolts.
STEP 4: Tighten all mounting bolts.
Setup
• Endure that the log is flat on the base, no wider than 20",
and no smaller than 5".We recommend that logs smaller
than 8" be sawn on a shop bandsaw.
• Fixed clamp may be moved forward by 1 ½ or 3” for
blade guide clearance, if necessary.
• The frame may be centered on the rails.
• Two additional 1/2" spacers (accessory number 123449)
can be used to raise the fixed clamp for specific needs.
• Ensure that the sliding clamp can move freely. Clean
debris, lubricate slide and/or platform, or loosen the 2 inside
bolts holding the clamp mount to the lead nut (NOT the bolts
holding the sliding clamp itself those should always remain
secure)
Operation
STEP 1: Lower the blade to the minimum height indicator
to ensure it does not interfere with any parts.
STEP 2: Load the log on the CookieMizer firmly against the
fixed clamp.
STEP 3: Use a 1/2" ratcheting wrench or drill (from either
side) to firmly seat the sliding clamp.
STEP 4: Ensure clamp teeth are engaged in the wood.
STEP 5: Cut the log according to your mill instructions.
Contact Us
Wood-Mizer’s website and online account system are built to
make your experience better. If you have comments, suggestions,
or feedback on how we can improve your experience, please
contact us at www.woodmizer.com
Mount Plates
6" bolts
Lock washers
Flat washers
Lower Mount
Toward blade
Mount Plates
5" bolts
Lock washers
Flat washers
Lower Mount
Toward blade
26" maximum span
between rails

Parts
Optional equipment
REF DESCRIPTION PART # QTY. REF DESCRIPTION PART # QTY.
COOKIEMIZER 123415 1 14 Nut, 5/16-18 Flanged Hex
Nylock
F05010-221 6
1Wldmnt, Lower Platform 123416 1 15 Bolt, 5/16-18x3 1/2 SHC BO F05006-154 4
Assy, Clamp 123405 1 16 Plate, Upper Platform 123420 1
Assy, Bearing 123443 2 17 Plate, Fixed Clamp Mount 123422 1
2Block, Sleeve Bearing 123406 1 18 Plate, Fixed Jaw 123423 1
3Bushing, 5/8IDx3/40Dx1
Flanged, Bronze
123407 1 19 Bracket, Platform Support 123440 2
4Screw, 1-5 Acme 123408 1 20 Washer, 5/16 SAE Flat F05011-17 17
5Wldmnt, 1-5 Acme Nut 123409 1 21 Bolt, 5/16-18 x 1 Gr 5 HH F05006-27 17
6Plate, UHMW, Bottom 123412 1 22 Nut, 5/16-18 Flanged Hex Nylock F05010-221 14
7Plate, UHMW, Top 123438 1 23 Washer, 5/16 Split Lock F05011-13 3
8Plate, Sliding Clamp Mount 123413 1 24 Washer, 3/8 Flat SAE F05011-3 2
9Plate, Sliding Jaw 123414 1 25 Bolt, 3/8-16 x 11/2 HH FT Znc F05007-17 2
10 Washer, 5/16 SAE Flat F05011-17 6 26 Nut, 3/8-16 Flanged Hex Nylock F05010-222 2
11 Washer, 5/16 Split Lock F05011-13 2 27 Bushing, Min Cut Indicator 123424 1
12 Bolt, 5/16-18 x 3/4 HH Gr5 F05006-102 2 28 Screw, 1/4-20x1 1/2 BO SHC F05005-122 1
13 Bolt, 5/16-18x1 3/4 SHC F05006-137 2 29 Nut, 1/4-20 Flanged Hex Nylock F05010-220 1
Description Part # Qty Description Part # Qty Description Part # Qty
SPACER, 1/2IN FIXED JAW 123439 1 KIT, FIXED JAW SPACER, QTY 1 123448 1 KIT, FIXED JAW SPACER, QTY 2 123449 1
1. Spacer, 1/2in Fixed Jaw 123439 1 1. Spacer, 1/2in Fixed Jaw 123439 2
2. Bolt, 5/16-18x1 1/2 HH Gr5 F05008-96 3 2. Bolt, 5/16-18x2 HH Gr5 F05006-79 3