WOPET FT80D User manual

Even Automatic Feeder
USER MANUAL
Model: FT80D

Have a Question For the Seller
Warranty Information
Reset to Factory Default
Cancel feeding schedule
Set the current time
Product Specifications
Feeder Assembly
Install the food tank
Install the bowls
Load in desiccant
Install the lid
Plug in the power
Set feeding meals
Recording
Manual feeding
Feeder panel introduction
Buttons Overview
FAQs
FCC WarningsFCC
[CONTENTS]
1
3
3
4
6
7
8
9
10
Setting Guideline 11
11
13
16
16
17
17
20
21
Feeder cleaning
Important notes
18
19
23
26

Product Specification
1
Model FT80D
Capacity 8L
Meals 4 meals per day
Screen LCD screen
One portion 12grams(8 portions max per meal)
Food size 2- 12mm(dry food only)
Battery-powered supply 3× alkaline D batteries (not included)
DC-powered supply 5V/1A
Operating temperature -10℃- 55℃/14°F-131°F
Dementions 23.5*23.5*33.5cm/9.3×9.3×13.2 inches
Product weight 2.4kg/5.29lbs

2
Lid
Feeder base
Meal Splitter
Control panel
Base
Food bowls
desiccant
Food tank
Turnplate

Feeder Assembly
3
Install the food tank
Align the feeder base with the tank and install the feeder as
indicated by the arrow shown.
1

4
2Install the bowls
Insert (1) one bowl into the main base, as hown in (2) and (3).
(1)
(2) (3)
2.1 Single food bowl

5
2.2 Dual food bowls
(4)
(5) (6)
Step 1: Install the bowls
Put the two food bowls together in the direction of the arrow
shown in figure (4), and then insert the food bowl into the main
base as shown in (5) and (6).

6
3
(7) (8)
Step 2: Insert the meal splitter
Install the meal splitter as indicated by the arrow as shown in (7),
from top to bottom in place as shown in (8).
Load in desiccant
Open the desiccant cap, put in the desiccant, and then close
the desiccant cap.

7
4Install the lid
First, align the lid to the tank and install from top to bottom, as
shown in (9). Next, fit into place, then rotate the lid clockwise
as shown in (10).
(9)
(10)

8
Step 2: Install 3 new D cell, alkaline batteries.(NOT Included)
Push the button switch to “I”. When the power is on, the
green light lights up, which indicates that the power is
normal.
Note:
(11)
5Plug in the power
Step 1: Open the batteries cover, as shown in (11). Insert the
power cable oriented, put the cable into the slot.

9
Feeder panel introduction
Work
Status Indicator
Microphone
Hole
Number
Increase/Decrease
Recording
Manual feeding
Abnormal
Indicator

10
Buttons Overview
Note:
The screen will lock automatically after 2 minutes of non-use.
Hold for 3s to unlock.
Button Description
Set /Save
Unlock button
Number
Increase button
Number
Decrease button
Manual button
Recording
button
Press to save and move to the
next step
Operable Mode Function
Press and hold for 3s to lock/
unlock other buttons and screen
Press to increase the value
Hold for digit increasing
automatically
Press to decrease the value
Hold for digit decreasing
Press to feed 1 portion
Hold for 3s and start recording
after a beep is heard {max 10s}
Recording saved after a double
beep is heard

11
Setting Guideline
In the setting state, the LCD light will turn off and exit the
setting when there is no operation for more than 2min.
(MUST BE UNLOCKED)
Press and hold the button for 3s until the LCD display lights
up and enter the hour setting mode. The two hour digits will
start to flash, press to set the "hour". Hold digits
will automatically begin to increase/decrease until the desired
time is displayed.
Step 1 — Set the Current Time
Note:
1.1-Hour setting

12
After setting the hour, press the button to save and enter the
minute setting. Press to set the "minute". Press the
button to save.
1.2-Minute Setting

13
(MUST BE UNLOCKED)
1. Press the button to enter the copies setting of the first meal.
At this time, the meal number labeled as the first meal "①" will
lights up.
2. Press the button to set the "copies". Then press the
button to save.
Step 2 — Set feeding meals
2.1-Set the copy of the first meal

14
The maximum number of copies is 8.
Note:
After setting the copies, press the button to save. The feeder
then enters the time setting mode. The setting method is the
same method as setting the current time.
2.2-Set the time of the first meal

15
After finishing setting the first meal, press the button to save
and the feeder then enters the setting mode of the second
meal"②". Follow the same steps as setting the first meal.
Repeat to set feeding schedules for the other meals. The
maximum meal is 4.
2.3-Set the 2-4 meals

16
STEP 3— Cancel feeding schedule
If you want to cancel the feeding of a meal, you just need to set
the "copies" number to 0.
Step 3.1
If you need to change the recording message, press the
button again to record.
Note:
STEP 4— Recording
When not in the setting state( LCD lights off)
Press and hold the button, it will make one "beep" sound.
At this time, speak loudly into the device's microphone, and it
will record your voice. (max 10s) A double beep indicates
recording is saved.
A recording will be played automatically when the recording is
completed.
A recording will be played once when feeding.

17
STEP 5— Manual feeding
When not in the setting state (LCD light is off), press the
button to dispense 1 portion.
STEP 6— Reset to Factory Default
When not in the setting state (LCD light is off)
Press and hold at the same time for 3s, all settings will be
cleared, and the feeder will be restored to factory settings and
restart automatically.