WURM FKL003-A User manual

FKL003-A
Product information
FKL003-A_V3.60_PI_2022-03_EN Subject to technical changes Page 1 of 4
Front view
Field module with semiconductor relay for EEV for advanced functions
Features
Control of 2 evaporators and 1 expansion valve per module, such as double islands
Operation of an electronic expansion valve:
- 230V~, pulsed direct
- Constant via output 0…10V
- Pulsed, 230V~ / 230V= with ATV230
Connection of 2 external displays
Connection of glass and handrail heaters on free display output through ECA970
Connection of refrigeration unit lighting
Connection of T3Sensor temperature sensors
Fixed input/output allocation for sensors, control inputs and relays
Emergency program in case of CAN bus errors
No parameters to be set on the device
CAN bus connection via patch cable and screw terminals (4-pin)
Replaces FKL002B
Connection to master module via Wurm CAN field bus (F-BUS)

FKL003-A
Product information
Page 2 of 4 Subject to technical changes FKL003-A_V3.60_PI_2022-03_EN
Writing conventions
Symbol
Meaning
CAUTION!
Avoid the described hazard: otherwise minor or medium physical injury or
damage to property will result.
WARNING!
Avoid the described hazard: otherwise there is danger from electric voltage
that could lead to death or serious physical injury.
For your safety
For safe operation and to avoid personal injury and equipment damage through operating error, always
read these instructions, become familiar with the device, and follow all safety instructions on the product
and in this document, as well as the safety guidelines of Wurm GmbH & Co. KG Elektronische
Systeme. Keep these instructions ready to hand for quick reference and pass them on with the device if
the product is sold.
Wurm GmbH & Co. KG Elektronische Systeme accepts no liability in case of improper use or use for
other than the intended purpose.
Target group
These instructions are intended for service technicians.
Intended use
The FKL003-A is a field module with semiconductor relay for EEV
applications
with advanced functions.
WARNING!
Danger to life from electric shock and/or fire!
Switch off the power to the entire plant when installing, wiring or removing! Otherwise a
mains voltage and/or external voltage may still be present even if the control voltage is
switched off!
The wiring of the device should be carried out only by a qualified electrician!
Use only the correct tools for all work!
Check all wiring after connection!
Take note of the maximum loads on all connections!
Never expose the device to moisture, for example due to condensation or cleaning
agents!

Take the device out of operation if it is faulty or damaged and is therefore compromising
safe operation!
Do not open the device!
Do not repair the device yourself! If required, send it in for repair with an exact
description of the fault!
CAUTION!
Electromagnetic interference can cause faults!
Use only shielded data lines and place them far away from power lines!
Software revision and validity of documentation
Software version
Valid from
V3.60
2022-03
Documentation status
Any software versions not listed are special solutions for individual projects and are not described in detail in this document. This
document automatically ceases to be valid if a new technical description is issued.
Manufacturer: Wurm GmbH & Co. KG Elektronische Systeme, Morsbachtalstraße 30, D-42857 Remscheid
For further information, see our website at www.wurm.de

FKL003-A
Product information
FKL003-A_V3.60_PI_2022-03_EN Subject to technical changes Page 3 of 4
Circuit diagram
Installing
WARNING! Danger to life from electric shock and/or fire!
Switch off the power to the entire plant before installing! Otherwise a mains voltage and/or
external voltage may still be present even if the control voltage is switched off!
53
106
90
58
This device is designed for top-hat rail
installation. The housing is of a standard size
and is also suitable for installation in fuse boxes,
distribution switch boxes or electric boxes of
refrigeration units.
The devices can be positioned immediately next
to one another and without gaps.
Place the device with the upper guide edge on
the top-hat rail.
Then press the device gently downward until it
engages with the fastening safety catch on the
top-hat rail.
Control of glass and handrail heaters via ECA970
For contactless switching of glass and handrail heaters, connect an ECA970 to the free display output
of the FKL003-A. To do this, use the pre-assembled ZCB-C/ECA-3.0 connecting cable.
Notes!
You must also observe the detailed description of the ECA970.
The control of a glass and handrail heater via the free display output of the FKL003-A
is only possible with HKS-G3 V7.62 or later.

FKL003-A
Product information
Page 4 of 4 Subject to technical changes FKL003-A_V3.60_PI_2022-03_EN
CAN bus address setting
To register the FKL003-A correctly on the CAN bus, you have to assign a unique CAN bus address to it
with the coding switch. This is a requirement for functioning communication with the master module.
You can set CAN bus addresses 0–7 with the coding switch. You can thus connect 8 field modules to
the CAN bus.
Encoding switch
Technical data
Power supply
230V~, +10% / -15%, max. 10VA
Display
1 x green LED, operating voltage
2 x green LED, CAN bus data traffic (CAN Tx, CAN Rx)
1 x red LED, flashing in case of fault
Communication
3-wire CAN bus interface, shielded, galvanically isolated,
screw terminals / RJ45 socket (2x)
Temperature sensor
6 x TRK277 (standard connection: 1 x common supply air, 2 x return
air, 2 x defrost limit, 1 x suction gas), T3Sensor
Analogue input
4…20mA or 0…10V=, output voltage 22V=,
max. 22mA (humidity sensor, transmitter)
Digital inputs
24V=, +20% / -10%, approx. 5mA per input,
1 x cold room off, 1 x 2nd setpoint, 1 x cold room door open
Cooling / valve output,
semiconductor relay
1 x 230V~, 4…60VA, note the minimum output!
Residual voltage measureable! Integrated semiconductor
protection (no isolator)
Output relay
1 x fan, normally closed contact, 230V~, 3(1)A
1 x light, normally closed contact, 230V~, 4(2)A
2 x defrost, normally open contact, 230V~, 3(1)A
Display / frame heating
connection
2 x socket for prefabricated cable to the display DSP002, DSP100,
DSP-LCD, DSP-Booster or for controlling frame heating through
ECA970 (1x)
Analogue output
1 x 0…10V=, non-isolated, max. load 10mA, for constant valves
PWM / EEV output
1 x 0…10V=, non-isolated, max. load 10mA,
for control of electronic relays through ATV230
Dimensions
(WxHxD) 106 x 90 x 58mm (DIN 43880)
Fastening
Top-hat rail TH 35-15 or TH 35-7.5 (DIN EN 60715)
Ambient temperature
Operation: 0...+55°C, storage: -25…+70°C
Weight
About 285g
CE conformity
−2014/30/EU (EMC Directive)
−2014/35/EU (Low Voltage Directive)
EAC conformity
−TR CU 004/2011
−TR CU 020/2011
RoHS II
Valid from
Version 3.60
Note!
Please observe the detailed descriptions in the chapters of the FRIGOLINK system
manual.