WURM FVB240-PAT User manual

FVB240-PAT
Product information
FVB240-PAT_V3.30_PI_2018-01_EN Subject to technical changes Page 1 of 4
Front view
Field module for switching and monitoring 4 condenser fans
Features
1 relay switch output 230V~ per fan
Fixed input/output assignment for sensors, control inputs and relay outputs
230V~ inputs for operation feedback messages and fault chain monitoring
Emergency program in case of CAN bus errors
Connection to master module via Wurm CAN field bus (F-BUS)

FVB240-PAT
Product information
Page 2 of 4 Subject to technical changes FVB240-PAT_V3.30_PI_2018-01_EN
Writing conventions
Symbol Meaning
CAUTION! Avoid the described hazard: otherwise minor or medium physical injury or
damage to property will result.
WARNING! Avoid the described hazard: otherwise there is danger from electric voltage
that could lead to death or serious physical injury.
For your safety
For safe operation and to avoid personal injury and equipment damage through operating error,
always read these instructions, become familiar with the device, and follow all safety instructions on
the product and in this document, as well as the safety guidelines of Wurm GmbH & Co. KG
Elektronische Systeme. Keep these instructions ready to hand for quick reference and pass them on
with the device if the product is sold.
Wurm GmbH & Co. KG Elektronische Systeme accepts no liability in case of improper use or use for
other than the intended purpose.
Target group These instructions are intended for service technicians.
Intended use The FVB240-PAT is a field module for switching and monitoring 4 condenser
fans.
WARNING!
Danger to life from electric shock and/or fire!
Switch off the power to the entire plant when installing, wiring or removing! Otherwise a
mains voltage and/or external voltage may still be present even if the control voltage is
switched off! Always remove both power plugs (230V~ and N)!
The wiring of the device should be carried out only by a qualified electrician!
Use only the correct tools for all work!
Check all wiring after connection!
Take note of the maximum loads on all connections!
Never expose the device to moisture, for example due to condensation or cleaning
agents!
Take the device out of operation if it is faulty or damaged and is therefore compromising
safe operation!
Do not open the device!
Do not repair the device yourself! If required, send it in for repair with an exact
description of the fault!
CAUTION!
Electromagnetic interference can cause faults!
Use only shielded data lines and place them far away from power lines!
Software revision and validity of documentation
Software version
V3.30 2018-01 Documentation status
Any software versions not listed are special solutions for individual projects and are not described in detail in this document.
This document automatically ceases to be valid if a new technical description is issued.
Manufacturer: Wurm GmbH & Co. KG Elektronische Systeme, Morsbachtalstraße 30, D-42857 Remscheid
For further information, see our website at www.wurm.de

FVB240-PAT
Product information
FVB240-PAT_V3.30_PI_2018-01_EN Subject to technical changes Page 3 of 4
Circuit diagram
Notes!
The CAN bus shield must be connected at only one (!) CAN bus end by means of the
6.3mm connecting lug with PE.
Further information on the CAN bus can be found in the FRIGOLINK bus system
manual.
Installing
WARNING! Danger to life from electric shock and/or fire!
Switch off the power to the entire plant before installing! Otherwise a mains voltage
and/or external voltage may still be present even if the control voltage is switched off!
Always remove both power plugs (230V~ and N)!
53
106
90
58
This device is designed for top-hat rail
installation. The housing is of a standard size
and is also suitable for installation in fuse boxes,
distribution switch boxes or electric boxes of
refrigeration units.
The devices can be positioned immediately next
to one another and without gaps.
Place the device with the upper guide edge on
the top-hat rail.
Then press the device gently downward until it
engages with the fastening safety catch on the
top-hat rail.

FVB240-PAT
Product information
Page 4 of 4 Subject to technical changes FVB240-PAT_V3.30_PI_2018-01_EN
Fault inputs that are not used
In order to obtain correct fault information, fault inputs that are not used must be jumpered with the
fault signal that is connected upstream within the alarm routing. The input "Operation 1/2/3/4" (terminal
22/24/26/28) is used for measuring the operating hours. If no corresponding signal is available from
the machine protection, then it is advisable to jumper the output relay.
Monitoring function / emergency program
In the event of an F-BUS fault, the field module enters an emergency program corresponding to the
operating mode.
If a problem with the cover identification arises at the same time, then all of the output relays are
switched off and the analogue output "A out" is set to 0V.
Module addressing
Make sure that each of the 8 field modules per master module (HVI-G3/G4: 12) has a different module
address. Permissible addresses are the values 0-7 (HVI-G3/G4: 0-B). No other settings are permitted.
The address of the module FIO001B / FIO-PAT and the addresses of the field modules FVBxxxB /
FVBxxx-PAT must not overlap. In the event of an address collision, an entry is made in the fault list of
the master module and the LED " " (fault) on the field modules flashes.
Technical data
Power supply 230V~, +10% / -15%, approx. 7VA
Display
1 x red LED, flashing in case of fault
1 x green LED, operating voltage
2 x green LED, CAN bus data traffic (CAN Tx, CAN Rx)
8 x yellow LED, for signal at the input
4 x green LED, for controlling the relays
Communication 2 x RJ45 sockets for CAN bus connection,
with integrated power supply, galvanically isolated
Digital inputs 8 x 230V~, galvanically isolated by optocoupler
Temperature sensor 1 x TRK277, S1 for external temperature
1 x DGF, S2 for deheating temperature
Analogue input 4...20mA, output voltage 18V=, condensation pressure
Output relay 4 x normally open contact 230V~, 4(2)A
Analogue output 1 x 0...10V=, non-isolated, max. load 10mA
Connection cross-section 2.5mm²
Dimensions (WxHxD) 106 x 90 x 58mm (DIN 43880)
Fastening Top-hat rail TH 35-15 or TH 35-7.5 (DIN EN 60715)
Ambient temperature Operation: 0...+55°C, storage: -25...+70°C
Weight About 450g
CE conformity 2014/30/EU (EMC Directive)
2014/35/EU (Low Voltage Directive)
EAC conformity TR CU 004/2011
TR CU 020/2011
RoHS II
Valid from Version 3.30
Note!
Please observe the detailed descriptions in the chapters of the FRIGOLINK system
manual.