WURM HVL-G3 User manual

HVL-G3
Product information
HVL-G3_PI_2012-04_EN Subject to technical changes Page 1 of 4
Front View
Universally programmable master module
Features
Programming of 200 function blocks, such as PI controllers, timing elements, etc.
Programming with the software Visulink Designer
4-line, blue-lit plain text display with 8-button control panel
Connection of a maximum of 16 field modules
Connection to the Wurm system over a CAN-bus connection and Frigodata XP
Note!
The main module HVL-G3 is only supported by Frigodata XP.

HVL-G3
Product information
Page 2 of 4 Subject to technical changes HVL-G3_PI_2012-04_EN
Writing conventions
Symbol Meaning
CAUTION! Avoid the described hazard: Otherwise minor or medium bodily injury or
property damage will result.
WARNING! Avoid the described hazard: Otherwise there is danger from electric voltage
that can lead to death or serious bodily injury.
For your safety
For safe operation and to avoid personal injury and equipment damage through operational error,
always read these instructions, become familiar with the device, and implement all of the safety
instructions on the product and in these instructions as well as the safety guidelines of Wurm GmbH &
Co. KG Elektronische Systeme. Keep these instructions ready to hand for quick reference and pass
them on with the device when the product is sold.
Wurm GmbH & Co. KG Elektronische Systeme accepts no liability in case of improper use or use for
other than the intended purpose.
Target group These instructions are intended for "service technician" personnel.
Intended purpose The HVL-G3 is a universally programmable main module.
WARNING!
Danger of death from electric shock!
Switch off the power to the entire system when installing, wiring or removing! Otherwise
a mains voltage may still be present even if the control voltage is switched off!
The wiring of the device should be carried out only by a qualified electrician!
Use only the correct tools for all work!
Check all wiring after connection!
Never expose the device to moisture, for example due to condensation or cleaning
agents!
Take the device out of operation if it is faulty or damaged and is therefore compromising
safe operation!
CAUTION!
Danger of fire if there is overloading of the connections!
Ensure the maximum loads on all connections!
Faults are caused by electromagnetic interference!
Use only shielded data lines and place them far away from power lines!
Damage to device if handled incorrectly!
Do not open the device.
Do not repair the device yourself! If required, send it in for repair with an exact
description of the fault!
Software revisions and validity of documentation
Software version Functional upgrade Page
2012-04 V7.2 Basis of documentation
Any software versions not listed are special solutions for individual projects and are not documented in detail in this description.
This document automatically ceases to be valid if a new technical description is issued. Manufacturer: Wurm GmbH & Co. KG
Elektronische Systeme. For further information, see our website at www.wurm.de

HVL-G3
Product information
HVL-G3_PI_2012-04_EN Subject to technical changes Page 3 of 4
Circuit diagram
Montage
WARNING! Danger of death from electric shock!
Switch off the power to the entire system before installing! Otherwise, external voltage can be
present even when control voltage is shut off.
Installation in the MGR
Installation with ZEM
Installation in the mounting frame MGR130/140
Push the device in the mounting frame to the stop until
it locks between the spring clips.
Note!
Please observe the product information for
the MGR130/140 module frame.
Individual installation with screw clamps of the ZEM
type
Insert the device up to the stop in a section of a
switching cabinet door. Then fix the device with screw
clamps of the ZEM type to the switching cabinet door.

HVL-G3
Product information
Page 4 of 4 Subject to technical changes HVL-G3_PI_2012-04_EN
Installation section for individual installation
Wiring and connection of several main modules
Technical data
Supply voltage 230V~, +10% / -15%, 50Hz., max. 13VA
Displays
4-line clear text display with background lighting
4 x yellow LED menu selection
1 x red LED, flashing in case of fault
1 x yellow LED for operating status of communication bus
1 x yellow LED for operating status of field bus
Field bus 3-wire CAN-bus interface, shielded, electrically isolated
Push-in terminals 2.5mm² or RJ-45 socket
Communication bus 3-wire CAN-bus interface, shielded, electrically isolated
Push-in terminals 2.5mm² or RJ-45 socket
Digital inputs 6 x 24V=, self-supplied, approx. 5mA per input, push-in terminals,
2.5mm²
Digital outputs 8 x closing contact with common supply,
1A, rated voltage 230V~, push-in terminals 2.5mm²
Dimensions (WxHxD) 109 x 109 x 92mm
Front plate Plastic, foil
Mounting In the module frame / individual mounting
Ambient temperature 0...+50°C operation / -25...+70°C storage
Weight About 650g
CE conformity
EC conformity according to
- 2004/108/EC (EMC Directive)
- 2006/95/EC (Low Voltage Directive)
RoHS
Valid from Version 7.0