Wyrestorm CON-H2-SCL User manual

2160p 4:4:4/60 In-Line HDMI Scaler with Audio Breakout
CON-H2-SCL Quickstart Guide
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
CON-H2-SCL Quickstart Guide | 190617
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Basic Wiring Diagram
IMPORTANT! Installation Requirements
• Advanced conguration of this product requires the use of the use of the
WyreStorm Management Suite v1.6 or higher conguration tool. Download
the latest version from the product page before continuing with the
installation.
• Visit the product page to download the latest rmware, document version,
additional documentation, and conguration tools.
• Read through the Wiring and Connections section for important wiring
guidelines before creating or choosing premade cables.
In the Box
1x CON-H2-SCL
1x DC 12V 2A Power Supply (US/UK/EU/AU)
3x 3-Pin Terminal Block
2x Mounting Brackets
1x Quickstart Guide (This Document)
MX-0404-H2A
Matrix
KEY
Passive HDMI
Control
Power
Digital Audio
CON-H2-SCL
Rear
CON-H2-SCL
Front
AC Mains
Audio Video
Receiver
HDMI to display
HDMI to display
HDMI to display
Control System
HDMI from
source
Blu-ray Player

Copyright © 2019 WyreStorm Technologies | wyrestorm.com
CON-H2-SCL Quickstart Guide | 190617
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
2 of 4
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results.
• WyreStorm recommends using pre-terminated HDMI cables due to the
complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
.
RS-232 Guidelines
This product uses a 3-pin RS-232 with no hardware ow control. Most control
systems and computers are DTE where pin 2 is RX, this can vary from device
to device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made.
3rd Party Device
Pin 1 TX (Transmit) ---> To ---> RX (Receive)
Pin 2 RX (Receive) ---> To ---> TX (Transmit)
Pin 3 G (Ground) ---> To ---> G (Ground)
WyreStorm Connector
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that the output resolution of the source and display is supported by
this product.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
• Verify that all source and display connections are not loose and are
functioning properly.
No or Intermittent 3rd party Device Control
• Verify that the RS-232 and Relay cables are properly terminated.
Refer to RS-232 Guidelines and/or Relay Wiring sections for pinout
information.

Copyright © 2019 WyreStorm Technologies | wyrestorm.com
CON-H2-SCL Quickstart Guide | 190617
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
3 of 4
Setup and Conguration
Scaler Settings
This device can be set to scale the video output when required by the system using the dip switches on the front of the device.
Auto Scaling (Default) 123
ON
1920x1080@60Hz
1024x768@60Hz 123
ON
1920x1200@60Hz
1280x720@60Hz 3840x2160@30Hz
1280x800@60Hz 3840x2160@60Hz
Advanced Conguration
The following steps require the use of the use of the WyreStorm Management Suite v1.6 or higher. Download the latest version from the product page before
continuing with the installation.
Initial Conguration Tool Setup
1. Connect the converter to a PC using the RS-232 port. Refer to RS-232 Guidelines for pinout.
2. Open the WyreStorm Management Suite and select the CON-H2-xxxx Conguration Tool from the menu.
3. Under RS-232 Port Conguration select the COM port for the PC and set the baud rate to 57600.
4. Select the Connect button to connect the PC to the converter.
EDID Write from a File
If an EDID le is available it can be uploaded into the converter for setting the desired EDID.
1. Under RS-232 Port Conguration select the COM port for the PC and set the baud rate to 57600.
2. Under EDID Write select Choose File to select the le to upload.
3. Once the selection dialog closes, select Import to upload the le to the converter.

Specications
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
CON-H2-SCL Quickstart Guide | 190617
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
4 of 4
Warranty Information
WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a
period of ve (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited
product warranty.
Note: WyreStorm reserves the right to change product specication, appearance or dimensions of this product at any time without prior notice.
Audio and Video
Inputs 1x HDMI In: 19-pin type A
Outputs 1x HDMI Out: 19-pin type A
1x S/PDIF Out: TOSLINK (Digital Optical)
Audio Formats HDMI Pass-through: 2ch PCM
S/PDIF Out: De-Embed: 2ch PCM
Video Resolutions (Max)
Video Resolution HDMI
1920x1080p @60Hz 12bit 15m/49ft
3840x2160p @24Hz 10bit 4:2:0 HDR 7m/23ft
3840x2160p @30Hz 8bit 4:4:4 7m/23ft
3840x2160p @60Hz 10bit 4:2:0 HDR 5m/16ft
3840x2160p @60Hz 12bit 4:2:2 HDR 3m/10ft
4096x2160p @60Hz 8bit 4:2:0 7m/23ft
4096x2160p @60Hz 8bit 4:4:4 3m/10ft
Supported Standards DCI | RGB | HDR | HDR10 | Dolby Vision | HLG | BT.2020 | BT.2100
Maximum Pixel Clock 600MHz
Communication and Control
HDMI HDMI 2.0 | HDCP 2.2 | EDID
Inputs supports DVI/D and DisplayPort Dual-Mode (DP++) v1.3 with adapter (not included)
RS-232 1x RS-232: 3-pin Terminal Block - 3.5mm
USB 1x USB: USB-A | Firmware Updates Only
Power
Power Supply 12V DC 2A
Max Power Consumption 8.38W
Environmental
Operating Temperature 32°F ~ 113°F (0°C ~ 45°C) | 10% ~ 90%, non-condensing
Storage Temperature -4°F to ~ 158°F (-20°C ~ +70°C) | 10% ~ 90%, non-condensing
Maximum BTU 29 BTU/hr
Dimensions and Weight
Rack Units | Wall Box <1U
Height With | Without Feet 25mm/0.99in
Width With | Without Brackets 110mm/4.34in
Depth With | Without Handles 150.1mm/5.91in
Weight 0.476kg/1.05lbs
Regulatory
Safety and Emission CE | FCC | RoHS | RCM