XIEGU X6100 User manual

Xiegu X6100 - Quick Reference
Menu buttons
Multi function
knob
Volume, Squelch,
RF Gain
- Push to select
Power
- Push and hold
1s to activate
Adjust
frequency
Push to talk
button
Mode AG switch
Pre-Amp
(Hold for Attenuator)
hange band Antenna Tuner
(Hold to tune)
Fast tune step
Multi Function
Tag
Spectrum
display Signal
Strength
dBm
Waterfall plot
area
Multi function
menu
Volume and connection
status
Function Status
Volume, Squelch,
RF Gain
- Push to select
Main VFO
display
S Meter
W alignment
VFO B
display
Audio
spectrum

Prepared by M0ODH ( )2022

AG KENN AG SLOPE AG HANG TX POWER MI SEL
AG start
control level
AG control
gradient
AG hold Transmitting
power
Microphone
selection
(built-in / hand
microphone)
I-MI GAIN H-MIN GAIN LINE IN LV LINE OUT LV MONI LEVEL
Built-in
Microphone gain
Hand
microphone gain
Line input level Line output
level
Monitor level
PTT MODE BANDSTA K S/P MODE HARGER
PTT mode Band display
mode
Headphone port
selection
(headphone /
loudspeaker)
harging switch
RIT XIT SPLE IQ OUT EN
Reception
frequency tuning
Transmission
frequency tuning
Split frequency
operation switch
IQ output switch
RF FFT AVE RF FFT REF WF REF AF FFT AVE AF FFT REF
RF spectrum
display average
RF spectrum
display
reference level
Waterfall reference
offset level
Audio spectrum
display average
Audio spectrum
display reference
level
BL LEVEL
Backlight
brightness
TIME FW UPGRADE FA TORY
RESET
Time setting Firmware update Restore factory
settings
TAG MARK ERASE MEMO SAVE VFO EXIT
Edit tag name Set mark lear current
channel
Store current
VFO into channel
Exit menu
GEN menu - Quick Reference
Prepared by M0ODH ( )2022


APP menu - Quick Reference
<1> MODE F / TONE RATE / SPEED RTTY SHIFT
Select RTTY /
W / BPSK
mode
arrier / Side tone
frequency
Baud rate / code
rate
Offset
<2> AF SQL LEAR EXIT
arrier tracking Modem muting lear text Exit
SPAN SPEED QUIT
Scanning
bandwidth
Scanning speed Exit
KEY menu - Quick Reference
<1> KEY TYPE KEY SPEED IAMBI TONE TONE LEVEL
Manual /
automatic mode
selection
Automatic key
rate
Iambic mode Side tone
frequency
Side tone
volume
<2> QSK TIME DI / DA RATIO W TRAINER
QSK time Dot and Dash
ratio
Training mode
switch
MSG menu - Quick Reference
<1> MGS 1 MGS 2 MGS 3 MGS 4 MGS 5
<2> MGS 1 MGS 2 MGS 3 MGS 4 MGS 5
These messages can be used for automatic transmission of W, RTTY and BPSK. lick any
MGS label to enter the editing interface
These messages can be used for automatic transmission of voice mode. lick any MGS label to
enter the editing interface
Prepared by M0ODH ( )2022


DFN menu - Quick Reference
DFL menu - Quick Reference
<1> NR NR DEPTH NB NB WIDTH NB LEVEL
Noise reduction
switch
Noise reduction
depth
Pulse blanking
switch
Pulse width Pulse depth
<2> DNF DNF ENTER DNF WIDTH
Digital trap switch Trap center
frequency point
Trap bandwidth
FILTER1 FILTER2 FILTER3 DEFAULT LOSE
Filter 1 Filter 2 Filter 3 Reset filter to
default
parameters
Exit
1) Select Filter 1-3 to enter.
2) Short press the MFK knob to switch and
select different edge-cut filters. The blue
trapezoidal box is the high-cut filter (H- UT),
and the red trapezoidal box is the low-cut
filter (L- UT).
3) Rotate the MFK knob to adjust the
parameters of the filter. After adjustment the
current filter parameters will be automatically
stored.
4) Short press [DEFAULT] to restore the filter
parameters selected to default parameters.
5) Short press [ LOSE] to exit the filter
interface.
6) The start frequency and cut-off frequency of
the filter can be adjusted, and the
overlapping region of the two trapezoidal
filter graphs is the actual range of the filter.
Prepared by M0ODH ( )2022
