Xilinx SP701 User manual
SP701 Software Install
and Board
Setup
June 2019
XTP552
© Copyright 2019 Xilinx, Inc. Xilinx, the Xilinx logo, Artix, ISE, Kintex, Spartan, Virtex, Vivado, Zynq, and other designated brands included herein are
trademarks of Xilinx in the United States and other countries. All other trademarks are the property of their respective owners.
NOTICE OF DISCLAIMER: The information disclosed to you hereunder (the “Information”) is provided “AS-IS” with no warranty of any kind, express or implied.
Xilinx does not assume any liability arising from your use of the Information. You are responsible for obtaining any rights you may require for your use of this
Information. Xilinx reserves the right to make changes, at any time, to the Information without notice and at its sole discretion. Xilinx assumes no obligation to
correct any errors contained in the Information or to advise you of any corrections or updates. Xilinx expressly disclaims any liability in connection with technical
support or assistance that may be provided to you in connection with the Information. XILINX MAKES NO OTHER WARRANTIES, WHETHER EXPRESS,
IMPLIED, OR STATUTORY, REGARDING THE INFORMATION, INCLUDING ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NONINFRINGEMENT OF THIRD-PARTY RIGHTS.
Revision History
Date Version Description
06/17/19 1.0 Initial version.
SP701 Software Install and Board Setup
˃Xilinx SP701 Board
˃Software Requirements
˃SP701 Hardware Setup
˃UART Driver Install
˃Terminal Setup
˃Clock Setup
˃Ethernet Setup
˃Optional Hardware Setup
˃References
Note: This presentation applies to the SP701
Xilinx SP701 Board
Software Requirements
˃Xilinx Vivado Design Suite 2018.3, HL System Edition with SDK
Note: Presentation applies to the SP701
SP701 Hardware Setup
˃Kit Hardware contents
SP701 Board
Micro USB cable
Ethernet cable
Power supply
Note: Presentation applies to the SP701
SP701 Hardware Setup
˃Connect a USB Type-A to Micro-B
cable to the USB UART connector (J5)
on the SP701 board
˃Connect this cable to your PC
˃Connect the power supply to the
SP701 (J30)
Connect this power supply to a power outlet
Note: Presentation applies to the SP701
UART Driver Install
˃Determine the COM Port numbers for your system
˃Open the Device manager
Control Panel →System →Device Manager
The COM Port numbers will vary from system to system
The COM Port numbers may be out of order
˃These COM Port Numbers will be used in several of the tutorials
Note: Presentation applies to the SP701
Terminal Setup
˃Refer to UG1036 regarding Tera Term installation
˃Board Power must be on before starting Tera Term
˃Start the Terminal Program
Set the baud to 115200
You may need to try the other two port numbers, as the COM Port numbers do not always
enumerate in order
Note: Presentation applies to the SP701
Ethernet Setup
˃Open the Windows Control Panel
Set to View by Category
˃Click on “View network status and tasks”
Note: Presentation applies to the SP701
Ethernet Setup
˃Click on “Change adapter settings”
Note: Presentation applies to the SP701
Ethernet Setup
˃Right-click on the Gigabit Ethernet Adapter that you will be using for this
test and select Properties
Note: Presentation applies to the SP701
Ethernet Setup
˃Click Configure
Set the Link Speed & Duplex to Auto Negotiation then click OK
Note: Presentation applies to the SP701
Ethernet Setup
˃Reopen the properties after the last step
˃Double-click the Internet Protocol Version 4
˃Set your host (PC) to this IP Address:
Note: Presentation applies to the SP701
Optional Hardware Setup
˃Using a common HDMI cable, connect
an HDMI Monitor to the HDMI port
(J13)
˃Tested with ViewSonic VP2780-4K
monitor
Note: Presentation applies to the SP701
References
References
˃Vivado Release Notes
Vivado Design Suite User Guide - Release Notes – UG973
‒https://www.xilinx.com/support/documentation/sw_manuals/xilinx2018_3/
ug973-vivado-release-notes-install-license.pdf
Vivado Design Suite 2018 - Vivado Known Issues
‒https://www.xilinx.com/support/answers/70860.html
˃Vivado Programming and Debugging
Vivado Design Suite Programming and Debugging User Guide – UG908
‒https://www.xilinx.com/support/documentation/sw_manuals/xilinx2018_3/
ug908-vivado-programming-debugging.pdf
Other manuals for SP701
1
Table of contents
Other Xilinx Computer Hardware manuals
Xilinx
Xilinx VC707 User manual
Xilinx
Xilinx 7 Series User manual
Xilinx
Xilinx DS610 User manual
Xilinx
Xilinx ML510 User manual
Xilinx
Xilinx Alveo U50 User manual
Xilinx
Xilinx MicroBlaze User manual
Xilinx
Xilinx ML510 Installation guide
Xilinx
Xilinx FMC XM107 Quick start guide
Xilinx
Xilinx Alveo U200 User manual
Xilinx
Xilinx XM104 User manual
Xilinx
Xilinx PCI32 User manual
Xilinx
Xilinx SP605 FMC Si570 Owner's manual
Xilinx
Xilinx FMC XM104 User manual
Xilinx
Xilinx Virtex-4 FX FPGA User manual
Xilinx
Xilinx CAST CZ80CPU User manual
Xilinx
Xilinx CAN FD v2.0 User manual
Xilinx
Xilinx ZCU102 User manual
Xilinx
Xilinx Kintex-7 FPGA KC705 User manual
Xilinx
Xilinx AC701 Si570 Owner's manual
Xilinx
Xilinx LogiCORE IP MAC v8.5 User manual
