XYZ Printing da Vinci Mini Series User manual

da Vinci Mini Series
User Manual
Specification
Product Overview
Button and Indicator light
Unpacking
Accessory Checklist
Important Safety Notes
Extruder module installation
Accessory installation
XYZware operation
Print
Wi-Fi setup (da Vinci Mini w only)
Advanced XYZware operation
Function descriptions
Using the accessory tools
Print Bed Adjustment
Error message and Action
2
2
2
3
3
3
4
4
6
6
7
10
11
14
15
16
English
V1 - 1 -

1
2
3
4
5
6
7
8
9
10
Guide tube
Feed module
Filament
Extruder module
Function button
/ status indicator
Print bed
Filament holder
Power connector
USB port
Power switch
Solid green
Flashing green
Solid red
Flashing red
Solid orange
Flashing orange
Pulsing orange
Indicator signals Status Action
Standby/Ready to print
Receiving data
General error
Critical error
Printing
Paused
-
-
Press the button to return to printing status, refer
to instructions in software to fix the issue.
To pause the print, press the button once. To
cancel the print, press and hold the button for 5
seconds.
Job complete (printing complete /
printing cancellation complete)
If the printer encounters issues, please refer to the XYZware screen troubleshooting instruction to fix
the issues.
Refer to instructions in the software to solve the
issue or reboot the Mini.
To resume the print, press the button once.
To return to Ready to print, press the
button once.
1
2
3
4
5
6
Specification
400 x 336 x 362 mm
8 KG
Fuse Filament Fabrication (FFF)
PLA
1.75 mm
0.4 mm
150 x 150 x 150 mm
0.1/0.2/0.3/0.4mm
USB 2.0 (da Vinci miniMaker)
USB 2.0/ WiFi (da Vinci Mini w)
XYZware
STL / 3W
Dimensions
Weight
Print Technology
Print Material
Filament Diameter
Nozzle Diameter
Print Dimension
Print Resolution
Connectivity
Print Software
File Format
Button and Indicator light
Product Overview
8
9
10
7
- 2 -

• Before using this printer, remove all fixed materials from the extruder module and
print bed. Switching on the printer without removing these fixed materials may
damage the machine.
• Be sure to remove the 4 clips from the shafts as illustrated on the right.
• Do not use the printer in dusty high humidity or outdoor environments.
• Place the printer on a stable and even surface to avoid it falling and causing serious injury.
• Do not put your hand into the machine during operation to avoid collision risk due to
movement of the machine or to avoid burn due to high temperature.
1. Quick Guide, Warranty Card
Keep original packaging materials in case you need to send your unit back for repair
during the warranty period.
If other packing materials are used instead, the printer may become damaged during transportation.
In such a situation, XYZprinting reserves the right to charge a repair fee.
Notes
13. Cleaning Wire x 511. Cleaning Brush
2. Power Adapter 3. Power Cord 4. USB Wire 5. Extruder Module
7. Guide Tube 8. Bundled Filament 9. Filament Spool Ring
(installed on the filament spool)
6. Scraper
14. Leveling tool
12. Feeding Path Cleaning Wire
10. Bed Tape X 3pcs （Only replace
the reusable tape when it is worn.）
16. Feeding Tube Grip X1
(For replacing and installing
the Feeding Tube Grip,
please watch the tutorial
video on XYZprinting official
website)
15. PET Protection cover
Unpacking
Accessory Checklist
Important Safety Notes
- 3 -

NOTE: To unload the extruder module, first detach the
heating bus and press the black disengage button.
Ensure that the guide tube
is properly inserted into the
feed port of the extruder
module to complete the
installation.
3
Ensure that the guide
tube has been tightly
inserted into the port.
1Feed the guide tube
through the slot at the
top of the printer to
the extruder module.
2
Make sure that the printer is
powered off. Place the extruder
module that the fitting pin is
secured the proper location.
1Insert the black ribbon
connector to complete
the installation.
2
Installing the
Accessories
1. Install the guide tube
Installing the
Extruder module
- 4 -

Handy tips
• The filament will load better when the tip of the filament is cut at a 45° angle.
• When the printer is not in use, raise the filament spool holder and close the side cover.
Lower the filament spool
holder on the left side of
the printer until horizontal.
Use a phillips screw-
driver to loosen the
securing screws of the
filament spool ring.
(please refer to this step if the axle ring is not installed on the spool)
Install the sensor chip.
Note the orientation of
the sensor chip on the
spool ring.
Use a phillips screw-
driver to tighten and
secure the spool ring
to complete the
installation.
Separate the spool ring
from both sides of the
spool.
Place the assembled
filament spool (with
the spool ring) on
the spool holder.
Press the release arm and
push the filament all the
way to the bottom so that
the front end of the
filament is completely
inserted into the extruder
module.
2
Remove the side cover by pressing down
firmly at the center on the left side of the
cover and pushing aside the cover. (pay
attention to where you apply your force to
ensure proper dismantling) Keep the side
cover securely for future use.
1 3 Take the tip of the
filament and
insert it into the
feeding hole.
4 5
3.Installing the filament
Feed both parts of the
spool ring through the
center hole of the
spool and assemble
them together.
Retrieve the filament
spool and chip.
2.Installing the Filament spool ring
21 3 4 5 6
- 5 -

After completing the hardware installation, download XYZware from the XYZprinting official website and install it
on your computer.
Before launching XYZware, connect the printer to your computer using the supplied USB cable and turn it on. For
an optimal user experience, we recommend following the instructions below:
Print
XYZware operation
Handy tips
Registration via XYZware before your
first print is strongly recommended.
When registered with XYZprinting, you
will receive latest technical supports
and updates. To register, simply click
"Register Now".
Before you start printing, please attach
the bed tape to the print bed. The print
bed tape is reusable, and can be
replaced worn.
If the room you are printing in is below
25 ℃/ 77 ℉, for greater adhesion,
apply glue to the bed tape.
After printing has started, check if the
first layer is stuck to the print bed.
Good base layer is one of the keys to
successful printing.
Open XYZware
1Open Functions panel 3
Load filament
4Close Functions panel 5Print 6
Import 3D file
Click Import and select the file to print.
2
- 6 -

1. The network printing function is only available when the printer and the
computer are both connected to the same wireless network.
2. Before connecting the printer, your wireless network settings need to be
adjusted. For more information, refer to the instruction manual of your
wireless router.
3. The wireless network's channel width needs to be set to 20 MHz for the
printer to connect to it wirelessly. Refer to the vendor instruction manual for
more information.
4. The Mini supports WEP, WPA, and WPA2 security encryption standards.
Wireless pass word information will be requested when setting up the
printer connection.
Wi-Fi setup (da Vinci Mini w only)
The printing status, including the printing progress,
elapsed time, and remaining time, will be shown while
printing. You can pause or cancel the printing task in this
window.
8When done, "Printing Complete"
will be shown on screen.
9After the print has finished,
use a scraper to remove the
printed object.
10
●Pre-setup
Connect the printer to your computer with the USB cable, and open
"XYZware".
Click the "Printer Monitor" button on the lower right corner on the
screen, open "Operation Function".
1
2
3
●Setting up Wi-Fi
• WEP • WPA • WPA2
Select the "Printer Monitor" icon to open the Wi-Fi connection settings.
- 7 -

Use the pull-down menu to view a list of
Wi-Fi connections available in the area, and
select the Wi-Fi connection that you wish to
connect to.
Wait for the printer to obtain the correct
information, provide the wireless password
and press Start wireless connection.
Select the USB COM port, click Connect >
Establish printer connection.
Click "Wireless Setting"
to view wireless print settings.
In the "Printer Monitor" window, select My
Printer > Scan to search for the connected
printer.
45
7 8 9
6
Enter the printer name, then press the Scan
button.
- 8 -

Note:
• Name the printer and wireless network with the alphanumeric characters only.
• If no connection is detected within 90 seconds, the printer will time-out. If this is the
case, check that the configuration process is correct and try again.
• Confirm your wireless network's security key on the router's wireless settings page.
Update the printer connection method.
10 XYZware will use the USB connection to
update the printer settings.
11 Once the connection method has been changed from
USB to Wi-Fi, you can unplug the USB cable and
continue with the printing process.
12
OK
- 9 -

Operating the printer with XYZware
When using the software to operate the printer, one must first place filament spool ring
pre-loaded with the filament at the axis to activate XYZware.
Click on the Printer Monitoring function at the lower right corner to activate the operating
function.
Then select the Printer Monitoring function icon to activate the USB connection (this step
would be similar to Wi-Fi setup steps 1 to 5).
The USB cable can be removed once the printing file
has been transferred. To monitor printing status,
please re-connect the printer and computer with the
USB cable and re-activate the Printer Monitoring
(function).
If information shown
on-screen is not
updated accordingly,
you may switch off
the operation func-
tion screen and then
switch it on again.
(Reload)
Import: Import .stl, .3w files
Export: Convert to .3w file
Save: Save .stl file
Print: Set print preference, transfer print file
Setting: Set software display language, preview color, Printer Type
About: Query, update software and firmware versions, open link to official website
Adjust display scale
View: Switch preview angle rapidly
Move: Move location of the model
Rotate: Change angle of the model
Scale: Adjust size of the model
Info: Display information about the model
Remove: Delete the model from the virtual platform
Printer Monitor: Open functio
A
A
B
C
D
E
F
G
H
I
J
K
L
M
N
G
H
I
J
K
L
M
N
B C D E F
- 10 -