XYZ Printing da Vinci nano User manual

Table of Contents
2 Product Overview
3 Printer Setup
6 Software Setup
7 Software Functional Descriptions
9 Maintenance
10 Troubleshooting
Thank you for purchasing da Vinci nano 3D printer. (Hereinafter referred to
as da Vinci nano. )This product is a small and portable 3D printer, you can
use da Vinci nano to take your imagination to a new level and bring any idea
to life.
Before you start printing, please read this manual to learn how to use da
Vinci nano correctly. This manual describes da Vinci nano safety instructions,
operating instructions, maintenance information and application tips. For
the latest information of da Vinci nano 3D printer, you can contact your local
Authorized Distributors or refer to the official website of XYZprinting. (http://
www.xyzprinting.com).
ENG
QUICK GUIDE
HD23FNAX085
XYZmaker is a software that is used to operate the da Vinci nano and prepare 3D models for
printing. Download XYZmaker from http://xyzptr.com/go2nano and install it on your computer.
First time installation requires an Internet connection.

2
Indicator signals Status Action
Solid green Standby/Ready to print -
Flashing green Receiving data -
Solid red General error Press the button to return to printing status, refer
to instructions in software to fix. *
Flashing red Critical error Refer to instructions in the software to solve the
issue or reboot the Nano. *
Solid orange
Printing -
Pause the print To pause the print, press the button once.
Cancel the print To cancel the print, press and hold the button for
5 seconds.
Flashing orange Paused -
Resume the print To resume the print, press the button once.
Pulsing orange Job complete (printing complete /
printing cancellation complete)
To return to stand-by mode, press the button
once.
8
9
12 13 14
1
3
5
2
6
4
7
11
10
Print Technology Fuse Filament Fabrication (FFF) Weight 4.5kg
Dimensions 378*280*355 mm Print Dimension 120*120*120 mm
Print Resolution 0.1-0.4 mm Nozzle Diameter 0.4 mm
Print Material PLA Filament Diameter 1.75 mm
Print Software XYZmaker File Format .3w/ .stl/ .3mf
Operating System Microsoft Windows 7 +
Mac OSX 10.9 + Connectivity USB cord 2.0
1. Top cover 5. Guide tube 9. Front cover handle 13. Power switch
2. Top cover latch 6. Detection head trigger 10. Feed module 14. USB port
3. Print bed 7. Extruder module 11. Filament holder
4. Function button/
Status indicator
8. Hold-open component 12. Power socket
Product Details
Specification
Button and Indicator light
Product Overview
*Please refer to "XYZmaker" software screen to solve the problem.

3
01
04
02
05
03
1
7
2
8
3
9
4
10
5
11
6
12
Unpacking
Accessory Checklist
Note
Printer Setup
1. Quick Guide & Warranty Card
2. Feeding Path Cleaning Wire
3. Nozzle Cleaning Wire x 5
4. Scraper
5. USB Wire
6. Guide Tube
7. Bed Tape x 3
8. Cleaning Brush
9. Feeder
10. Power Adapter
11. Power Cord
12. Bundled Filament
Keep original packaging materials in case you need to send your unit back for repair during the
warranty period.
If other packing materials are used instead, the printer may become damaged during
transportation. In such a situation, XYZprinting reserves the right to charge a repair fee.
Take out the accessories,
top cover and printer.
Remove the styrofoam
packing material on sides
and the plastic bag.
Remove the fixed tape
on front cover sides.
Remove the fixed tape on
the extruder module and
print bed packaging.
Remove the fixed
tape from the printer
bottom and take out the
filament.
06 Remove the fixed tape on
the filament spool holder
and the feed module.

4
Install the Guide Tube and Extruder Module
Printer Setup WARNING: Hazardous Moving
Parts. Keep Fingers and Other
Body Parts Away.
01 Insert guide tube into the
extruder module port.
Press the white button and
align the extruder module with
the bracket. Once aligned,
release the white button to
connect the extruder module
with the bracket.
04 Connect the flat cable to the
extruder module. (Be sure to
insert the flat cable in the right
direction.
10 Ensure that the guide tube has
been tightly inserted into the
feed module port.
07 Feed the guide tube through
the top cover. 08 09 Direct the bottom locking catches toward their slots
then press the latch to rotate
clockwise.
Attach the top cover to the
machine.
The flat cable is bending for
printing smoothly purpose,
please do not adjust.
03 Follow the illustration to bend
the flat cable.
06 Use the cramp ring to hold the
filament guide tube and flat
cable. (Place the cramp ring on
the flat cable marker.)
NG Follow this method
Note To load the filament, refer
to the [Software Setup]
section.
05
02

5
Install the sensor chip.
Note the orientation of the
sensor chip on the spool
ring.
Feed both parts of the
spool ring through the
center hole of the spool
and assemble them
together.
04 05
Use a Phillips head
screwdriver to loosen the
securing screws of the
filament spool ring.
Lower the filament spool
holder on the back side of
the printer until horizontal.
Separate the spool ring
from both sides of the
spool.
Place the assembled
filament spool (with the
spool ring) on the spool
holder.
Take out the filament spool
and the sensor chip.
Use a Phillips head
screwdriver to tighten and
secure the spool ring to
complete the installation.
01
01
02
02
03
06
*If you have just unboxed the da Vinci nano, the sensor chip should
already be loaded.
Printer Setup
Replace the New Filament Spool
Installing the Filament
Note
•The filament will load better
when the tip of the filament
is cut at a 45° angle.
•When the printer is not in
use, raise the filament spool.

6
Load Filament Printing
Software Setup
Open up XYZmaker and click
File >Print >da Vinci Printer.
This will display a print screen that lets you set print
settings and prepare your printer.
01
Follow the on-screen instructions to install the
filament.
03
Click DASHBOARD then click Filament > Load Filament
Take the tip of the filament and insert it into the
feeding hole. The printer will start to load the filament
automatically.
02
04
a
b
c
01
03
02
Click File > Open. Import your favorite 3D files. Click
on the object to adjust the size you need.
When you're done adjusting the print parameters
you need, click PREPARE.
When the object is adjusted, you can start printing.
Click File > Print > da Vinci Printer.
•When the printer starts printing, you can monitor the status by
clicking DASHBOARD.
•The recommended operating temperature is 15℃~ 32℃(59 ℉
~ 90 ℉). If the room temperature is above this, please open the
front cover to maintain print quality.
•After the print is finished, the object may be removed with a
scraper.
•When using different types of filament, we recommend changing
the extruder module.
Note
After preparing, please check if the object is a complete
model. After the confirmation, click PRINT.
04
＊ For better printing results, we recommend that you calibrate before
printing.
XYZmaker is a software that is used to operate the da
Vinci nano and prepare 3D models for printing. Download
XYZmaker from http://xyzptr.com/go2nano and install it
on your computer.
First time installation requires an Internet connection.

7
Extruder Filament
Interface Introduction
Once this function is
selected, the nozzle will
heat up automatically and
move the nozzle to a proper
location where you can
easily clear away all residual
plastic on the nozzle.
Clean
Nozzle
The extruder module
information, including
Temperature, Nozzle
Diameter, Total Print Time,
and Serial Number.
Info
Extruder Filament Setting
Software Functional Descriptions
Information related to
filament use.
Please follow the on-screen
instructions.
The extruder module will
automatically move to
the working position. The
nozzle will then heat up
and begin the filament
loading process. After this is
complete, verify that plastic
has been extruded. If not,
please repeat the filament
loading process.
Load
Filament
Please follow the on-screen
instructions.
Unload
Filament
Info
The printing module will
automatically move to the
working position. The nozzle
will then heat up and begin
the filament unloading
process.

8
Setting
Interface Introduction
Please follow the on-screen
instructions.
Print bed calibration may be
implemented before the printing
process.
Move the extruder module to the
lower left corner of the printing
area. Please refer to the calibrate
instructions provided by the
software.
Z-Offset function will help you to
adjust the printing distance between
the print bed and extruder module.
Each adjustment has a step of 0.05
mm.
Manually adjust the movement of X/Y/Z
Axis for printer maintenance.
Jog Mode
Calibrate Z-Offset
Move extruder module
rightwards and leftwards.
Move extruder module
forwards and backwards.
Move the print axis (Z-AXIS)
upwards and downwards.
Software Functional Descriptions
Others
Automatic horizontal calibration Restore DefaultBuzzer
Info
FW upgrade
Automatic horizontal calibration
may either be ON or OFF.
Default: ON.
The software would automatically
implement horizontal calibration
and compensation accordingly.
Printing speed will be improved if
automatic horizontal calibration
has been switched to OFF.
However, this may affect printing
quality.
Buzzer may either be ON
or OFF. Default: ON.
When the buzzer is
turned on, the printer will
output an audible signal
when a button is pressed,
receiving data, print job
is finished, or issue is
detected.
Click Restore Default
to reset to default
setting.
Please upgrade the latest
firmware version for the best
printing quality of the printer.
Information related to printer
setting.
Note 1. First click on Home Axes.
The extruder module will be
returned to the initial axis
position.
2. You may manually enter
the adjustment value:
Range: 1 to 150; step: 1 mm

9
•This product is factory tested and adjusted,
we suggest you note the default value for
z-offset before your adjustment.
•Suggested distance between nozzle and
print bed(including bed tape) is 0.3mm.
Note
Step
Tool
Z-offset
Clean the filament feed module
When the printing module has been moved, we
recommend that you use z-offset. This function will
help you to adjust the printing distance between
the print bed and the extruder module.
In order to maintain a good printing quality, it is
recommended that you clean the nozzle after every
25 hours of printing. Please use the Clean Nozzle
function in the software.
After long periods of use, the automatic feed
system may inconsistently extrude filament, due to
a buildup of residual plastic in the feed module. The
printer filament feed module should be cleaned if
this happens or after cleaning the nozzle.
Please switch off the power
before cleaning the filament
feed module.
Print bed calibration
Print bed level will affect the 3D printing quality,
XYZprinting's 3D Printer has been adjusted to the
best condition before leaving the factory. After long
periods of use, the print bed level may change. If
you have print adhesion problems, you may need
to re-level the print bed.
1. Open the feed module cover.
2. Clean the gears by using a gear cleaning
brush.
Cleaning Brush
Clean the nozzle
1. Switch on the power and click
DASHBOARD > Extruder > Clean Nozzle.
2. Please clamp the
nozzle cleaning wire
with needle-nosed
pliers to insert it into
the head of the nozzle
carefully for cleaning.
1. Please unload the filament and clean the
nozzle before using z-offset.
2. Click DASHBOARD > SetUp > Z offset to
start z-offset adjustment.
3. Adjust Z up or Z down to find the proper
distance.
1. Switch on the power and activate the
Calibrate function in XYZmaker.
2. Please follow the on-screen instructions.
Step
Step
Step
Tool Nozzle Cleaning Wire
Feeding Path Cleaning Wire
01 02
Maintenance
3. Lightly press the spring around the feed
hole and remove the filament guide tube
(don't need to remove the heating cable
at the side)
4. Insert the Feeding
Path Cleaning Wire
into the feeding path
all the way down and
“floss” the inside of
the nozzle to pull the
residue out.
5. After cleaning the
feeding path, reinstall
the filament guide
tube and extruder
module.

10
Error
Code
No.
Software interface Action
0007
0008
Spool 1 Error. Please remove spool and install again.
If errors persists, please contact service center for
support.
Reinstall or replace the filament cartridge.
0011
0014
Heating Error. Please turn off the printer and contact
service center for support.
Check whether the connections are connected properly and
restart as required.
0016
Spool 1 not installed properly. Please reinstall spool
1 ([Unload Filament] then [Load Filament]) on your
printer. If error persists, please contact service center
for further support.
Reinstall the filament cartridge.
0028 Spool 1 can not be found. Please install one. Reload or replace the filament.
0029 There is no filament left in spool 1. Please replace
spool 1 before printing. Replace filament immediately.
0030 Printer motor Error(X-Axis). If error persists, please
contact service center for support.
Check motor/sensor connections. Check sensor position.0031 Printer motor Error(Y-Axis). If error persists, please
contact service center for support.
0032 Printer motor Error(Z-Axis). If errors exist, please
contact service center for support.
0050 Memory error, please contact service center for
support. Reboot the printer.
0051 Flash ram cannot be read/written.
0052 Memory in the extruder cannot be read/written. Replace the nozzle.
0201 Computer and printer connection issues.
Re-connect the computer with the printer. Alternatively,
you may use hot plugging of the USB cable to connect the
computer with the printer.
Troubleshooting