XYZ Printing da Vinci Super User manual

Safety Precautions 2
Product Descriptions 3
Unpacking and Installation 5
Touch Screen Menu, Functions and Messages 7
Function Operation and Instructions 8
Printing 19
Support detail 20
XYZprinting 3D Printer
User manual ENG
The manual is mainly intended for users to understand how to
use the da Vinci Color 3D printer (“da Vinci Color”) correctly.
In this manual, users can learn more about the operating tips,
application skills and maintenance of the da Vinci Color 3D printer.
Please refer support.http://support.xyzprinting.com to download
latest manual & software for better user experience.
New member is required to register account on the website
before able to access to those resources.
For more information on the da Vinci Color 3D printer and the
complete XYZprinting product line, please contact your local dealer or
visit the ofcial website of XYZprinting: http://www.xyzprinting.com.

P2
Please read through this manual and all safety precautions carefully before using, operating, unpacking, replacing, remov-
ing any part or maintaining this product. Please also comply with the instructions of relevant safety precautions.
●Do not move the machine by yourself as it is heavy.
●Do not place the printer in a dusty, humid or outdoor environment.
●Do not place the printer on a soft or tilted surface. Otherwise, the machine will fall / ip over and become damaged or
cause personal injury.
● Do not leave the product or power cord to unattended children. Otherwise, personal injury or electric shock might occur.
●Use the provided power cord. Otherwise, incorrect grounding might lead to damage.
●Do not place any liquid container on top of the product. Otherwise, overow or spill might go into the machine and pose
the risks of danger or safety concern.
●Do not wipe the printer with alcohol or ammable chemicals. Otherwise, danger might occur.
●Do not move the machine when it’s powered on.
●Do not reach into the machine with your hands during operation. Otherwise, risks of impact from moving printing parts or
burn from high temperature might occur.
●The machine becomes hot during operation and thus run in high temperature. Do not touch or replace parts when they
are not cooled down.
●After startup, the parts in the machine will heat up or move depending on the user’s instructions. During product
operation, do not touch or block the operation of the parts.
●Weak odors may be generated during the printing process. We recommend working in a well-ventilated and open area to
ensure operational comfort.
●Defect reparation must be carried out according to the contents of this instruction manual. Where the defect cannot be
repaired, please contact your printer dealer or the customer service center.
All trademarks and registered trademarks are the properties of their respective owners.
When the printer needs to be serviced during the term of the warranty, it is recommended that the machine is packed with
original packaging materials prior to shipment. For this purpose, the packaging materials are better to be kept. If other
packaging materials are used instead, the printer might be damaged during printing. We reserve the right to assess rele-
vant service fees.
P2
Safety Precautions
Safety and Compliance
Important Safety Precautions
Trademarks
Maintenance and Service
CAUTION
Heavy object.
2 person lift
required
Watch Your Hands.

P3
Product Descriptions
Product exterior
1. 5 inch color touch panel 2. Auto-feeding module 3. Print head 4. Print bed+EZ removable rubber magnet
5. Filament spool holder 6. USB Port 7. USB Port (WiFi dongle) 8. Power switch
9. USB Port (To PC) 10. Power jack
1
3
2
5
4
6
7
8
10
9

P4P4
Precautions and Instructions of
Maintenance Tools
Specications
31 2 4 5
Printing
Printing technology 2D pattern: Inkjet printing
3D structure: Fused lament fabrication (FFF)
Dimensions and Weight
Dimensions (W*D*H) 600* 581* 640 mm
Net weight 32 Kg
Gross weight 43 Kg
Performance
Printing dimensions (W*D*H) Mono color printing (without inkjet printing)
200 x 200 x 150 mm
Full color printing
185 x 185 x 150 mm
Thickness of printed layer 0.1 mm ~0.4 mm
Alignment precision X/Y : 0.0125 mm
Auto calibration Yes
Auto feeding Yes
Ofine standalone printing Yes
Materials
3D printing materials 3D Color-inkjet PLA, PLA, Tough PLA, PETG
Filament diameter 1.75 mm
Ink type CMYK cartridge with separate colors
Hardware
Print head diameter 0.4mm
User interface 5” color touch screen
Print bed Non-heated, removable
Transmission USB 2.0 drive / USB cable / wireless transmission
Software
User software XYZmaker
Supported le format AMF, PLY, OBJ, STL, 3CP
Operating system Mac OS X 10.10 / 10.11 / 10.12
Windows 7 /8/10 (64-bit)
Linux 14.04
Temperature
Machine operating temperature 15-30°C
Cartridge storage temperature 15-35°C
Filament storage temperature 0-38°C
The following tools are intended for use under the guidance or guard-
ianship of an adult only. Do not allow children unfamiliar with the tools
to have access to them in case of danger.
Product Descriptions
Accessory Checklist
1234
11
5 6
12
7 8
1. Quick Guide 7. Top Cover
2. USB drive 8. Guide Tube
3. 3D Color-inkjet PLA 9. PC Mylar x 2
4. Power cord 10. Mask Tape
5. USB cable 11. WiFi Dongle
6. EZ Removable Rubber Magnet 12. Pair of gloves
●Make sure the maintenance work of the printer is carried out when
the print bed has cooled down.
●When printing is completed and the print bed is cooled down to room
temperature, the printed object can be removed from the print bed
with the scraper.
●Filament residues generated during the course of printing may
be stuck on the print head and gears of the printing module. The
printing quality and printer operation as well as the measurement of
the print bed may be affected. When this happens, clean the printing
module with the wire brush.
1. Scraper 4. Feed hole cleaning wire
2. Wire brush 5. Print head cleaning wire
3. Gear cleaning brush
910

P5
Unpacking and Installation
Remove the packaging materials, top cover box, assessory box and plastic cover.
3
8
Remove the foam next to the guide screws on both sides, and then remove the foam under the print bed.
Remove the tape on the body (4 in
total).
4
Move the printer to a table or plat-
form. (Do not move the printer by
yourself as it is heavy.)
1
Remove the plastic wrap and PP.
2
Open the front door. Remove the
tape from the supporting aterials
and print bed.
6
Remove the foam on the cartridge
holder.
7
Open front door, remove the tape at mark printer door post
5

P6P6
Place the top cover down with the
guide tube going through the hole in
the top.
11
Insert the guide tube through the top
cover, and then insert one end into
the printing module.
10
Conrm the rubber magnet is well placed on the print bed.
13
Insert the other end of the guide tube into the feed module and
secure it tightly.
12
Remove the cable tie and foam in front and back of the front door.
9
Unpacking and Installation
There is a sheet of PC film to
rubber magnet with a double
sided adhesive, this PC film is
replaceable, please replace it
when it's dirty or broken.
Note
1. Check if the print bed calibration
screws was stuck.
2. Used to 2 thumb to push up the print-
bed to release the calibration screw.
Precautions

P7
Touch Screen Menu, Functions and Messages
This includes Filament, Ink Load
and Unload.
Filament/Ink loading
and unloading
This menu can be used to import
les (.3cp) from a USB drive to the
machine for printing without a com-
puter.
This includes the functions in Home
Page 1:
Settings of the Print-Bed, Print-
Head, Filament and Ink.
Next page includes
WiFi, Sound, Statistics, Language
and Display.
The last page includes
Model, Version, Reset and Legal
Info.
Settings
USB Printing Menu
Main screen

P8P8
Unload the prints
Function Operation and Instructions
1. Check if the USB drive is
plugged to the machine.
2. Tap the USB Printing Menu in
the main screen.
3. Select the file you want to
print.
5. The screen will show the
print percentage when printing.
The Pause, Stop, and Rell
are shown below the print
percentage.
4. Check file information and
tap “Print”.
2. Place the lament on the spool
holder.
1. Please cut the lament at 45
angle before auto loading the
lament into the printer. During
loading lament process, the lament
should be straighten at least 4” of the
Filament end as shown in pictures.
A. USB printing
B. Load/unload filaments
Make sure the lament rotates
clockwise when pulled.
Note
3. Tap Filament Load and Unload in
the main screen and select Filament.
4. Tap Filament.
5. Tap Load. 6. Conrm the operation. 7. Insert the lament into the feed module, it will be automatically loaded.
8. Check if the temperature of the print head goes up to 210 °C (Color PLA from XYZprinting) after the lament is
loaded. Once the set temperature is reached, the feeding motor will feed the lament along the guide tube into the
print head.
9. Once lament has extruded from
the print head, the filament will be
successfully loaded. Tap the screen
to conrm and continue.
By default, the front door will
be locked when printing. If you
want to change this setting, go to
Setting > Door Lock to change it.
Note
Load filaments
B1 Filament
Please removed the EZ Removable Rubber Magnet with printed object together from the print-
er.And peel off the printed object from the rubber magnet.
A1
Please avoid touch-
ing the led strip of the
printer because the
LED strip will be slight
hot due to long hours
of been light on.

P9
1. Tap Filament Load and Unload on the
main screen.
1. Tap the icon when printing.
da Vinci Color will prompt you to rell material.
4. When the print head has been
warmed up to 220 °C, the feeding motor
will eject the lament.
2. Tap “Unload” and conrm the operation.
2. The screen will show lament status,
please tap "Rell" .
4. The nozzle will be preheated and the
lament will be unloaded automatically.
6. The nozzle will be preheat and notify you when to insert lament into the feed module. 7. The lament will be automatically loaded.
5. When the unloading operation
completes, tap to conrm.
3. Conrm the unloading operation.
3. Conrm the operation.
5. Replace the empty spool with a new one. (please refer to the LOADING section in this manual)
and then tap "PROCEED" .
Function Operation and Instructions
8. Check if lament is extruded from the nozzle, after conrmation, the printer will resume printing.
Unloading filaments
B2 Filament
Refill Material
B3 Filament

P10P10
The da Vinci Color uses four color inks which can be replaced separately.
C. Ink Cartridge Installation
Function Operation and Instructions
1. Prepare several paper towels and the
ink cartridge.
2. Unpack the ink cartridge. 3. Remove the cartridge cover.
Ink Guidance
6. Check if the ink transferred to the
paper towel displays two straight lines.
If so, ink guidance is successfully
completed. Once ink guidance is done,
install the ink cartridge.
4. Press the cartridge head against the
paper towel to transfer some ink onto it.
5. If the ink did not transfer well, try
putting the paper towel on the table and
hold the ink pressed on the paper towel.
7. If the ink did not transfer well, please
wet the paper towel with 75% Alcohol to
wipe the ink. After you clean the inkjet,
check to see if the ink transferred.