XYZ Printing PartPro150 xP User manual

Version 1.0
PartPro150 xP 3D Printer
(Model No. 6L20X)
Operation Manual
Please always refer to the updated version of PartPro150 xP operation manual
https://pro.xyzprinting.com/
For safe and correct use, be sure to read the Safety Precautions before using the machine.

Version 1.0
PartPro150 xP Operation Manual
i
Document History
Date
Description
Version
2019-12
Initial Release
1.0

Version 1.0
PartPro150 xP Operation Manual
2
INTRODUCTION
The PartPro150 xP is a stereolithography 3D printer that uses UV laser to cure photosensitive resins.
During the printing process, the UV laser traces the cross-section patterns on the surface of the resin
layer by layer. The nature of laser and UV resin presents parts with fine details and smooth surface finish.
DISCLAIMER
This manual is designed for users to understand how to use the PartPro150 xP printer in a safe manner. Please
read through all sections especially the safety guide carefully before unpacking, operating, replacing, and
removing any part of this product.
INTENDED USE
•User must read and understand the contents of this installation and user manual as following. Failure to
read the manual may lead to personal injury, inferior results or damage to the PartPro150 xP.
•Before performing any operations on the machine and/or packaging of the various parties should read this
entire instruction manual. This contains important information for the safety of persons engaged in routine
maintenance, the persons involved in the use and operation of the machine.
•This manual refers to the machine on which the model number is indicated on the title. XYZprinting
reserves the right to make technical changes on the machines and manuals without prior notice.
•No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, recording, or otherwise, without the prior written permission of
XYZprinting. For this entire user guide, please contact authorized reseller or XYZprinting customer service
for providing.
•Requests for additional copies of this manual should be directed to customer service of XYZprinting.
LIMITATION OF WARRANTY AND LIABILITY
XYZprinting is responsible for the device in its original configuration. Any changes to the configuration of the
machine must be performed or authorized by the XYZprinting technical department. XYZprinting is not
responsible for the problems and warranty dues to the use of not original spare parts or printing materials.
TRADEMARK
All trademarks and register trademarks are the property of their respective owners.
Copyright © 2019 XYZprinting, Inc. All Rights Reserved.

Version 1.0
PartPro150 xP Operation Manual
iii
TABLE OF CONTENTS
INTRODUCTION ...............................................................................................................................................2
DISCLAIMER.....................................................................................................................................................2
INTENDED USE..........................................................................................................................................................2
LIMITATION OF WARRANTY AND LIABILITY..............................................................................................................2
TRADEMARK .............................................................................................................................................................2
SAFETY AND COMPLIANCE ...............................................................................................................................1
IMPORTANT SAFETY PRECAUTIONS .........................................................................................................................1
SAFETY AND REGULATION........................................................................................................................................2
HANDLING AND OPERATING PRECAUTIONS ............................................................................................................2
WORK PLACE REQUIREMENTS..................................................................................................................................2
RECOMMENDED PROTECTIVE EQUIPMENT.............................................................................................................2
PRECAUTIONS BEFORE OPENING THE PROTEVTIVE COVERS...................................................................................2
NOTICES ON HANDLING / RECYCLING /DISPOSAL PRINTING MATERIALS................................................................3
PRINTING MATERIAL.................................................................................................................................................3
PRINTING PROCESS...................................................................................................................................................3
LASER MODULE.........................................................................................................................................................3
NOTE ON POWER SUPPLY.........................................................................................................................................3
1. UNPACKING AND INSTALLATIONS.................................................................................................................4
UNPACKING ..............................................................................................................................................................4
HARDWARE INSTALLATION ......................................................................................................................................6
SOFTWARE INSTALLATION......................................................................................................................................10
2. PRODUCT OVERVIEW .................................................................................................................................11
APPEARANCE ..........................................................................................................................................................11
ACCESSORIES LIST...................................................................................................................................................12
INSTALLATION SUGGESTIONS.................................................................................................................................13
Installation Environments...................................................................................................................................13
Optimal Placement.............................................................................................................................................13
FEATURES................................................................................................................................................................13
Resin Refilling......................................................................................................................................................13
Wiper ..................................................................................................................................................................13
SPECIFICATIONS......................................................................................................................................................14
SUPPORTED FILE FORMAT......................................................................................................................................15
USER INTERFACE.....................................................................................................................................................15
TOUCH SCREEN.......................................................................................................................................................16
XYZPRINT AMUV.......................................................................................................................................................17

Version 1.0
PartPro150 xP Operation Manual
iv
OVERALL WORKFLOW ............................................................................................................................................18
3. OPERATING THE PRINTER ...........................................................................................................................19
PRINT MENU...........................................................................................................................................................19
Structure of the PRINT menu..............................................................................................................................19
Start printing from the history............................................................................................................................20
Managing the printing history............................................................................................................................20
RESIN MENU ...........................................................................................................................................................21
Structure of the RESIN menu..............................................................................................................................21
Switching on/off auto-refilling............................................................................................................................21
SETTINGS MENU.....................................................................................................................................................22
Structure of the SETTINGS menu........................................................................................................................22
Adjusting the display brightness and timeout....................................................................................................23
Adjusting the audio volume................................................................................................................................24
Changing the display language...........................................................................................................................24
Structure of the Wireless icon............................................................................................................................25
Connecting to a Wi-Fi network...........................................................................................................................25
Connecting to a hidden Wi-Fi network...............................................................................................................26
Enabling Ethernet connection ............................................................................................................................27
Manually configuring Ethernet network ............................................................................................................28
Viewing the IP address .......................................................................................................................................29
PRINTING CONTROLS..............................................................................................................................................30
Monitoring the progress.....................................................................................................................................30
Pausing the printing............................................................................................................................................30
Resuming the paused task..................................................................................................................................31
Canceling the printing.........................................................................................................................................31
Switching off auto-refilling .................................................................................................................................31
Display language.................................................................................................................................................32
Display unit.........................................................................................................................................................32
Auto positioning .................................................................................................................................................32
Printer type.........................................................................................................................................................32
Dimension fine-tuning........................................................................................................................................32
4. OPERATING XYZprint AMUV.........................................................................................................................33
SOFTWARE INTERFACE...........................................................................................................................................33
KEYBOARD SHORTCUTS AND MOUSE CONTROLS..................................................................................................35
CONNECTING TO THE PRINTER...............................................................................................................................35
COLOR DISPLAY OF OBJECTS ..................................................................................................................................36

Version 1.0
PartPro150 xP Operation Manual
v
PREFERENCE SETTINGS...........................................................................................................................................36
Display language.................................................................................................................................................37
Display unit.........................................................................................................................................................37
Auto positioning .................................................................................................................................................37
Printer type.........................................................................................................................................................37
Dimension fine-tuning........................................................................................................................................37
PREPARING THE FILES.............................................................................................................................................38
Importing Models to the Workspace..................................................................................................................38
MANIPULATING MODELS ON THE WORKSPACE ....................................................................................................38
Repositioning models .........................................................................................................................................38
Rotating the models ...........................................................................................................................................39
Resizing the models............................................................................................................................................39
Adding supports automatically...........................................................................................................................40
Editing supports manually..................................................................................................................................41
Cone supports.....................................................................................................................................................41
Tree Supports .....................................................................................................................................................44
CONVERTING TO THE PRODUCTION FILES .............................................................................................................46
Exporting the files...............................................................................................................................................46
Starting a printing task........................................................................................................................................47
SAVING MODELS ON THE WORKSPACE..................................................................................................................47
SWITCHING THE VIEW OF THE WORKSPACE..........................................................................................................48
VIEWING THE INFORMATION OF THE MODELS .....................................................................................................49
SYSTEM VERSION AND UPDATE .............................................................................................................................49
5. POST-PROCESSING .....................................................................................................................................50
CLEANING UP THE MODELS FROM THE PLATFORM...............................................................................................50
POST-PROCESSING..................................................................................................................................................51
Alcohol bath........................................................................................................................................................51
Support removal.................................................................................................................................................51
Sanding ...............................................................................................................................................................51
Post-curing..........................................................................................................................................................51
MAINTENANCE .......................................................................................................................................................52
Filtering resin in the tank....................................................................................................................................52
Preservation of the Uncured Resin.....................................................................................................................52
APPENDIX......................................................................................................................................................53
APPENDIX 1 TROUBLE SHOOTING ..........................................................................................................................53
Error code on the printer....................................................................................................................................53
Error code in the software..................................................................................................................................54

Version 1.0
PartPro150 xP Operation Manual
1
SAFETY AND COMPLIANCE
IMPORTANT SAFETY PRECAUTIONS
Please read through all sections especially the safety guide carefully before unpacking, assembling, operating,
replacing, and removing any part of this product. Please also comply with the instructions of relevant safety
precautions.
Label
Safety Notic
1
WARNING - CLASS 3B LASER RADIATION WHEN OPEN
AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO THE BEAM.
Keep the covers securely closed during printing.
Complies with 21 CFR 1040.10 and 1040.11 except
for conformance with IEC 60825-1 Ed. 3.,as
described in Laser Notice No. 56, dated May 8, 2019.
2
CAUTION: HOT SURFACE
The metal frame holding the resin tank gets hot to
keep resin temperature around 25℃. Do not touch
the metal frame. Contact may cause burn.
1
2

Version 1.0
PartPro150 xP Operation Manual
2
SAFETY AND REGULATION
Please carefully read this notice, all safety precautions, and comply with safety rules when using,
operating, unboxing this product, replacing or removing any components, or maintaining this product.
For more information related to the PartPro150 xP 3D Printer or XYZprinting, visit the official website
(https://pro.xyzprinting.com/) or contact a sales representative.
HANDLING AND OPERATING PRECAUTIONS
Only trained personnel may operate the machine.
Do not try to disassemble, modify the product, otherwise fire, electric shock, or damage may
result.
Do not open the covers or remove the screws or parts other than instructed in the user manual,
otherwise fire, electric shock, or damage may result.
Laser hazard. Do not stare at the laser light as it may cause damage to the eyes.
If you notice any strange noises, smoke or strange odors, shut down the power of the product
immediately and contact service for further instruction.
Do not try to disable or cheat any sensors on the product, otherwise injury or electric shock may
result.
Be sure to read the Material Safety Data Sheet of each material and follow the handling
instructions before using the product.
Wipe off any printing material spilt on any components of the product immediately with a dry
cleaning wiper or dampened with water or ethanol, or the spillage may cause malfunction of the
product or fire.
Make sure to set the power switch to the off position and remove the power cord before
transporting the device.
Only use the grounded power adapter and power cord supplied with the printer to prevent
possible electrical shocking.
WORK PLACE REQUIREMENTS
Avoid exposing the product to direct sunlight or other UV radiation. The printing materials inside
the product may get cured when exposed to external UV source and result in malfunction.
Please do not place any containers with water on (or around) the product; if liquid spills out or
into the machine, it may lead to risk or safety concerns.
Place and use the printer in a well-ventilated area. The process of printing will produce a small
amount of non-toxic odor.
Prohibit use of fire, sparks and heat source.
For a stable printing performance, do not touch or move the product during production.
This machine is not suitable for use in location where children are likely to be present.
RECOMMENDED PROTECTIVE EQUIPMENT
Chemical-resistant gloves.
PRECAUTIONS BEFORE OPENING THE PROTEVTIVE COVERS
Always wear the chemical-resistant gloves to prevent direct contacting with printing materials.

Version 1.0
PartPro150 xP Operation Manual
3
NOTICES ON HANDLING / RECYCLING /DISPOSAL PRINTING MATERIALS
Keep the storage of the printing materials locked up and out of the reach of children.
Always wear the chemical-resistant gloves to prevent direct contacting with printing materials.
Wasted resin can be pulled into plastic bag and cured under sunlight or UV light source. Cured
resin can be discarded as office waste.
Be careful not to spill the resin material.
Do not mix the resin with incompatible materials.
Do not drain the printing materials or waste solution into sewer systems or with household
wastewater.
Follow local regulations for disposing the wipers dampened with the printing materials.
PRINTING MATERIAL
The stability of printing quality is affected by temperature and humidity. Please ensure that the
recommended operating conditions are adhered to (Operating temperature 20-30℃(68-86
℉)/humidity 40-80% RH)
PRINTING PROCESS
Keep the covers securely closed during printing.
The printing quality may be affected if resin temperature is changed due to opening the cover(s).
LASER MODULE
The Laser Module will emit lasers only after the printing starts.
The Laser Module will automatically shut down if any of the protective cover is open.
NOTE ON POWER SUPPLY
Do not use with damaged cord or plug. To unplug grasp the plug, not the cord. Do not handle plug
or machine with wet hands. Turn off the power switch before unplugging.
Do not run the machine over cord. Keep cord away from heated surfaces.
If the system is left in idle mode for an extended amount of time, turn off the main switch.

Version 1.0
PartPro150 xP Operation Manual
4
1. UNPACKING AND INSTALLATIONS
UNPACKING
Unpack the product follow instructions closely. Damage to parts may result if the procedure is not
followed.
Keep original packaging material in the event of sending the unit for service or repair.
1. Remove all external packing materials, plastic bag and
tapes on the covers.
2. Get the power adapter and the power cord from the
accessory box in the package.
3. Connect the power adapter, power cord to the
printer and switch on the printer.
4. Follow the instructions on the printer screen and
complete the initial system setup, including the
settings of the display language and wireless
connection (optional).
5. Lift up the printer from the front and release the
printing module lock by pushing it to the right.
6. Open the front cover and remove the packing
materials behind the cover. After removing the
cardboards, the protective pad and the cover sheet
over the glass, close the cover and tap [v].

Version 1.0
PartPro150 xP Operation Manual
5
7. Move up the platform rack by tapping the following options on the screen:
8. Complete the hardware installations. Tap [>] on the screen after installing each item.
Refer to p.6 to p.8 for detailed instructions on the installation.
•Install the platform.
•Install the resin tank.
•Install the wiper.
•Install the resin bottle.
•
•
9. Set up Wi-Fi connection or tap [Not now] to skip the
set up.
10. Tap[v] to complete the initial setting.
Error message 2009 will show
up during the setup, since the
tank is not yet installed.
Simply tap [PROCEED] to close
the message at this stage.

Version 1.0
PartPro150 xP Operation Manual
6
HARDWARE INSTALLATION
Complete the following installation after unpacking the product. Be sure to follow the installation
instructions closely. Damage to parts may result if any item is installed incorrectly.
The printer is ready for production after completing the following installation.
To install the platform:
1. Open the front cover.
2. Make sure the bolt handle connecting to Z-axis
is loosen.
3. Hold the platform and mount it onto the platform rack. 4. Tighten the bolt handle securely.
Push all the way until reaching the end.

Version 1.0
PartPro150 xP Operation Manual
7
To install the resin tank and the wiper:
1. Open the front cover.
2. Unpack the resin tank from the package and remove
the tank lid
3. Insert the tank into the tank slot. Push all the way until
reaching the end.
4. Loosen and remove the fixing bolt over the wiper shaft.
5. Mount the wiper on the wiper shaft.
6. Insert the fixing bolt to the wiper raft and fasten the
bolt.

Version 1.0
PartPro150 xP Operation Manual
8
To install the Resin Bottle:
1. Shake the resin bottle well to ensure even color.
For the material with dense pigment, you may
need to tilt the bottle at 45°for 5 minutes, and
then shake the bottle for around 5 minutes.
2. Assemble the nozzle cap and
the inner tube.
3. Replace the sealing cap with the
assembled nozzle cap.
4. Push to open
the side cover.
5. Insert the resin bottle into the
bottle slot.
6. Attach the exhaust tube to the thin nozzle. Find
the black filling tube on the left side of Z-axis
and attach it to the thick nozzle. Push the tubes
all the way down.
7. Close the side cover.
Be sure to run the filling tube from the back of Z-axis to the
nozzle cap while installing the cartridge. The platform will
be trapped if the tube goes from the front.

Version 1.0
PartPro150 xP Operation Manual
9
To check the resin information
The printer detects the information of the resin installed through the ID tag at the bottom of the resin
cartridge. Printing is not allowed when the cartridge is empty or when the material installed mismatch
the resin selected while exporting.
[Note: resin level is not available on the printer screen for the beta test. It will be added soon.]
You can read the resin information on the printer screen and through the software XYZprint AMUV:
Using the printer screen:
From the main menu, tap [RESIN].
Using XYZprint AMUV:
From the main menu, tap [RESIN].

Version 1.0
PartPro150 xP Operation Manual
10
SOFTWARE INSTALLATION
“XYZprint AMUV” should be installed on the service PC for preparing the files for production.
To install the software:
1. Double-click on the installer
[XYZware_***.exe].
2. Click [Next >] to initial the
installation.
3. Review the license agreement,
select [I accept the agreement] if
appropriate, and press [Next >].
4. Check if the default Installation
folder is accepted, and click
[Next>].
5. Check if the default Start Menu
Folder is accepted and click
[Next>].
6. Check if you want to add the
desktop icon and click [Next>].
7. Review the installation settings
and click [Install].
8. Wait while the installation is in
progress.
9. The installation is complete when
below screen appears. Click
[Finish] to close the setup wizard.

Version 1.0
PartPro150 xP Operation Manual
11
2. PRODUCT OVERVIEW
APPEARANCE
Front View - Exterior
Rear View
Front View - Interior
Component
Description
D
Ethernet Port
Attach the Ethernet cable to the port to connect the printer to the Ethernet.
E
USB Wire Port
Attach the USB cord to the port to connect the printer to the PC.
F
Power Jack
Connect the supplied power adapter to the socket to power on the printer.
G
Power Switch
Press the switch to power on or off the printer.
H
Platform Rack
The printing platform to hold the printed parts during printing.
I
Tank Slot
The tank slot holds the resin tank on the printer. Insert the resin tank into the slot while
completing the installation.
J
Wiper Shaft
The wiper shaft holds the wiper on the printer.
K
Cartridge Slot
Resin bottle should be inserted into the slot to connect to the refilling system.
L
Filling Tube
Resin runs through the filling tube when auto-refill is enabled.
M
Pumping Tube
Air flows into the resin bottle through the pumping tube to push out the material when filling.
Component
Description
Front Cover
Open this cover to take out printed model or perform regular
maintenance.
Keep the front cover securely closed during printing.
Side Cover
Access the resin bottle through the side cover.
Touch Panel
Contains a screen and keys for machine control.

Version 1.0
PartPro150 xP Operation Manual
12
ACCESSORIES LIST
Item
Name
Image
Quantity
Description
Packing
Location
Resin Tank
1 pc
The resin tank holds the resins for printing.
②
Wiper
1 pc
For wiping away the debris in the resin in the
tank and for stirring the resin to ensure the
evenness of temperature and color.
①
Platform
1 pc
Resin gets cured on the platform when
exposed to laser light.
③
Rinse Bucket
1 pc
Use the rinse bucket to wash the printed parts
in alcohol.
④
Scraper
1 pc
For removing printed parts from the platform.
①
Gloves
5 pairs
Gloves should be worn to avoid direct
contacting with the printing materials.
①
Starter Resin
500g/bottle
500g of printing material for starting your
production.
③
Nozzle Cap
1 pc
For attaching filling tubes on the printer to the
resin cartridge.
①
Inner Tube
1 pc
Attach the inner tube to the nozzle cap
①
Power
Adapter
1 pc
The external power supply of the printer.
Always use the bundled power adapter on the
product.
③
Power Cord
1 pc
For connecting the printer to the electricity
supply.
Always use the bundled power cable on the
product.
③
USB Wire
1 pc
For connecting the printer to the PC.
③
①Over the top cushion
②In the tank box
③In the accessory box
④Behind the front cover

Version 1.0
PartPro150 xP Operation Manual
13
INSTALLATION SUGGESTIONS
Installation Environments
Make sure the installation site follows below conditions:
Power requirements: AC 100~240V 50/60Hz 60W
Ambient temperature: 20-30°C (68-86°F)
Ambient humidity: 40-80% RH non-condensing
Optimal Placement
Follow below guidelines when positioning the printer:
Place the printer on a leveled and solid surface, or resin level detection may be inaccurate.
FEATURES
Resin Refilling
The printer refills the resin tank automatically before printing and when low tank level is detected. The auto-
refilling function eliminates the hassle of manual refilling and prevents incomplete prints due to material shortage.
Once the resin bottle is attached to the refilling system, the detecting system monitors the resin level
automatically.
Wiper
The wiper stirs the resin in the tank to ensure the evenness of resin temperature and color. The movement of the
wiper is noticeable once the printer is powered on, even when the system is idle. This ensures that the resin in
tank is ready for printing all the time.
Component
Description
A
Filling
faucet
Resin flows out from the filling
faucet to the tank when the
resin level is low.
B
Level
sensor
The level sensor detects the
resin level in the tank by
reading the positioning of the
floater.
C
Floater
The floater floats on the
surface of the resin in the tank.
D
Wiper
For stirring the resin in the
tank.
A
B
C
D

Version 1.0
PartPro150 xP Operation Manual
14
SPECIFICATIONS
General
Technology
SL (Stererolithography)
Light Source
UV Laser λ 405nm
Maximum Build Area (W x D x H)
150 x 150 x 200 mm (5.9 x 5.9 x 7.9 inch)
XY-axis Resolution
130 microns
Z-axis Resolution
25 / 50/ 100 / 200* microns (*Material dependent )
Connectivity
USB Wire/ WiFi / Ethernet
Product Dimensions (W x D x H)
280 x 337 x 595 mm (11 x 13.3 x 23.4 inch)
Product Weight
13Kg (28.66lbs)
Operation Software
XYZprint AMUV
Printing /File Types
.stl format / XYZ format (.3ws / .3wn)
Operating System
Window 10/ 10 Pro (64-bit)
Mac OSX 10.12 and up
Power Requirement
AC 100~240V 50/60Hz 60W
Minimum System Requirements
Memory (RAM)
8GB or more
Hard Drive
1GB or more free space for installation
Graphic Card
Support OpenGL 2.1+
Operating Environment
Operating Temperature
20-30℃(68-86℉)
Operating Humidity
40-80% RH