XYZ Printing da Vinci 1.0 User manual

da Vinci 1.0 User Manual
P 1
da Vinci 1.0 User Manual

da Vinci 1.0 User Manual
P 2
This manual provides detailed instructions on how to use your new da Vinci 1.0 3D Printer. The
instructions are for your safety and to properly maintain your printer. Visit our website http://www.
xyzprinting.com or contact your sales representative to get the latest available information on your
da Vinci 1.0 3D Printer.
Doc Edition Month Year
2014July1.4

da Vinci 1.0 User Manual
P 3
CONTENT
Chapter 1 Important Safety Instruction ................................................................................ 4
Chapter 2 Overview ..............................................................................................................6
Chapter 3 Installing and Set Up ............................................................................................8
Chapter 4 Connect the Cable ...............................................................................................9
Chapter 5 Load the Filament ..............................................................................................10
Chapter 6 Printer Functions ................................................................................................12
6-1 UTILITIES ................................................................................................................13
6-1.1 LOAD FILAMENT.............................................................................................14
UNLOAD FILAMENT ............................................................................................15
6-1.2 HOME AXES......................................................................................................... 16
6-1.3 JOG MODE............................................................................................................17
6-1.4 BUILD SAMPLE.....................................................................................................18
6-2 SETTINGS ...............................................................................................................19
6-3 INFO.........................................................................................................................19
6-3.1 STATISICS.............................................................................................................20
6-3.2 SYSTEM VERSION.............................................................................................. 20
6-3.3 FILAMENT STATS................................................................................................. 20
6-4 MONITOR MODE..................................................................................................... 21
6-5 Print Bed Adjustment............................................................................................ 22
Chapter 7 Q&A ....................................................................................................................23
Chapter 8 Term of Service .........................................................................................27

da Vinci 1.0 User Manual
P 4
Chapter 1 Important Safety Instruction
Please read this manual carefully before operating the printer. The following warnings and attention
notices are a best effort attempt to cover all scenarios; unfortunately it is not possible to do so. In
the case of performing maintenance procedures that are not described in this manual the burden
of safety falls to the customer side.
For basic safety and precautions adhere to the following:
●Do not let children operate this device without adult supervision. Electric shock hazard. Moving pars can
cause serious injury.
●Do not place the printer on an unbalanced or unstable surface. Printer may fall or tumble causing harm
and/or injury. Printer may fall or tumble causing harm and/or injury.
●Do not place any objects on top of the printer. Liquids and objects that fall into the printer can lead to
printer damage or safety risks.
●Do not use flammable chemicals or alcohol wipes to clean this device.
●Do not disassemble or replace the printer cover with none XYZprinter covers.
●Do not touch heated surfaces during or after operation. Heated surfaces can cause severe burns.
●Insert and secure the power cord firmly for proper usage and to avoid potential electricity and fire dangers.
●Do not attempt to service the printer beyond the instructions specified in this document. In the case of
irrecoverable problem, contact XYZprinting service center or your sales representative.
Warning
Attention
●Please place and use the printer in a well ventilated area. The process of heating the filament will produce
a small amount of non-toxic odor. Having a well ventilated area will ensure a more comfortable environment.
●This printer is only to be used with filament specified by XYZprinting.
●Make sure to set the power switch to the off position and remove the power cord before transporting the
device.
●Some components of the printer are moving during operation. Do not attempt to touch or change anything
inside before power off the printer.

da Vinci 1.0 User Manual
P 5

da Vinci 1.0 User Manual
P 6
Chapter 2 Overview
This chapter describes the unpacking and set up of the printer. Before proceeding to this chapter,
please make sure read the Chapter 1. Important Safety Instruction is acknowledged carefully.
Attention
●Retain the box and packing material. If the need arises,it will be used to transport the unit.
●This device without packing material or box is wighted around 23Kg (50lb). Handle the printer carefully to
prevent personal injury and damage of the printer.
A
B
Packing support x2
Tapex2
Cable tie x1
GLUESTICK
PRINTING
Open the box
23
6
57
8
9
14
A
B
Open the top cover, then remove
packaging supports and tapes from
inside.
Remove the print bed shipping tapes and
foam cushioning pieces.
Remove the bottom screw and the
plastic piece under print bed.
Remove the drip tray packaging
tapes.
Open the box and
remove the accessories
and the cushion.
Take out the printer
by holding the side
handles.
Remove plastic
bag and tapes.
Remove the cardboard.
Use the USB cable to connect the
printer to PC. Connect the power
cord to the printer then turn on the
power switch.
Note: Cable tie illustrated in step 4 in this section is used to fix the extruder during transportation.
It should be removed before powering on the printer, or the printer may not funtion normally.

da Vinci 1.0 User Manual
P 7
Display Panel: information on printer status.
Key Pad: use to operate functions in the printer.
Extruder Module: to be used for printing 3D objects.
Z-Axis Rod: to be used to provide print-enabled lifting heated bed module.
Access Door: to be used for operating or maintenance.
Print bed: provides a flat surface to lay the 3D model.
Cartridge Slot: space for placing the filament cartridge.
USB Port: used for connecting the USB cable.
Power switch: this switch turns on/off the power of the printer.
Power Connector: to be used to connect the power cord.
Once the 3D printer is turned off, wait at least 3 seconds before turning it on again.
Attention
GLUE STICK
．Filament Cartridge
．Power Cord
．USB Cable
．Decorative Plate x2
．Software CD
．User Quick Guide
．Cartridge Locker
．Glue Stick
PRINTING
．Copper Brush
．Cleaning Wire x5
．Scraper

da Vinci 1.0 User Manual
P 8
Chapter 3 Install and Set Up
Parts name and functions
Front View
Top View
Rear View
Left View
Right View
Bottom View

da Vinci 1.0 User Manual
P 9
Chapter 4 Connect the Cable
<A. USB Port / B. Power Outlet>
Connect USB Cable and Power Cord
Connect the printer power cord and USB cable to the back of the printer.
Power On the Printer
Please switch the power button to “I” icon ,the information of printer will be shown on the panel, it
is ready to print.
Display Panel
Warning
●Make sure to set the power switch to the “off ” position before inserting the power cord.
●Make sure the power cord is properly connected. Incorrect use may cause damage to the printer.
●Make sure to remove the power cord from printer if you are storing or not using the printer for an extended
period of time.
●Make sure to avoid power strips to power the printer . Use a wall outlet.

da Vinci 1.0 User Manual
P 10
Chapter 5 Load the Filament

da Vinci 1.0 User Manual
P 11
Shipping notice:
●Please unload the filament before printer shipping.
●Please use the regular carton and protection material.
●Do not put the printer in the carton while extruder or heated bed still warm and make sure both are completly
cool down before packing.
Attention

da Vinci 1.0 User Manual
P 12
Chapter 6 Printer Functions
Functions of Control Panel Key on the printer:
Button Functions
Direction Up
Direction Down
Back to pervious menu
Forward to submenu
OK; confirm selection/settings
Home Button, return to main menu
Function Description
UTILITIES
SETTINGS
INFO
MONITOR MODE
Printer adjustment / Change filament / Sample printing
The parameters of printer
The firmware and printer statistical information
Monitor of extruder and heated bed working temperature and printing progress

da Vinci 1.0 User Manual
P 13
6-1 UTILITIES
Function Description
CHANGE CARTRIDGE
HOME AXES
JOG MODE
BUILD SAMPLE
Loads/unloads filament
Moves the extruders and print bed to default "home" location
Manually adjusts the movement of X/Y/Z Axis for printer maintenance
Prints sample build

da Vinci 1.0 User Manual
P 14
6-1.1 LOAD FILAMENT
1.Choose “CHANGE FILAMENT” > “LOAD
FILAMENT”.
2.Please wait for extruder to reach
working temperature.
3. Push the filament through the filament
guide tube to the hole of the extruder and
press “OK” button.
4. Please follow instructions on the panel
and press “OK” to finish this process; it is
normal if filament color comes out not you
excepted in the beginning . Some filament
left over inside the extruder form last
printing.

da Vinci 1.0 User Manual
P 15
6-1.2 UNLOAD FILAMENT
1.Choose “CHANGE FILAMENT” >
“UNLOAD FILAMENT”.
2.Please wait for extruder to reach
working temperature.
3.Pull the filament through the
filament guide tube to the hole of
the extruder and press “OK” button.

da Vinci 1.0 User Manual
P 16
6-1.3 HOME AXES
1.Choose the HOME AXES function
and press “Yes”,extruder and
heated bed will move to proper
positions.
2.Wait for extruder and heated bed
moving process finish.
3.Refer the information from display
panel, process complete message
will be shown, press “OK” to return
main screen.

da Vinci 1.0 User Manual
P 17
6-1.4 JOG MODE
1.Choose the proper axis and press
“OK” to next steps.
Options:
X AXIS / Y AXIS / Z AXIS
2.Select adjustment degree
●Use Upper / Down button to switch
adjustment degree.
●Use Left / Right Button to apply a
default scale.

da Vinci 1.0 User Manual
P 18
6-1.5 BUILD SAMPLE
1.Choose printing sample.
2.Press “OK”, printer will be start to
print.
3.Printing status will be refresh on
the LCD panel
●BUILDING : the percetenge of
printing finish.
●TIME PASS : elapsed build time.
● ESTIMENTD : estimation of build
time.

da Vinci 1.0 User Manual
P 19
6-2 SETTINGS
6-3 INFO
Function
BUZZER
AUTO HEAT
LANGUAGE
RESTORE DEFAULT
Directions
Buzzer for alerting
Keep the extruders and print bed at working temterature when printer is powered on
Set the language displayed on the panel. Available options: English & Japanese
Apply default settings
Default
On
Off
English
Function
STATISTICS
SYSTEM VERSION
CARTRIDGE STATS
Directions
Used time of printer
Version of firmware
Capacity, remaining of filament

da Vinci 1.0 User Manual
P 20
6-3.1 STATISICS
●LIFETIME : Amount printing time of the printer
●LAST TIME : Printing time of last task in this printer
6-3.2 SYSTEM VERSION
Printer version information will be shown on the display panel
6-3.3 FILAMENT STATS
Some information related to filament which in the printer will be shown as below:
●REMAINING : remaining length of filament
●CAPACITY : original length of filament