Yale Keyfree Connected Smart Lock User manual

smart
Living
Keyfree Connected
Smart Lock
Installation Manual
The smarter way to protect your home
•
Please read the instructions before tting and using the
Keyfree Connected lock.
Due to a continuous programme of development the company
reserves the right to make alterations without notice.
Version No. 1A

Contents
1. Inside the Box
2. Multipoint Locking Compatibility
3. Fixing the Cylinder
4. Fitting The Spindle
5. Fitting The Handing Screw
6. Installation
7. Check Points after Installation
8. Electronically Handing the Lock
9. Troubleshooting
10. Quick Reference
1
2
3
5
6
1
1. Inside the Box
Fit the Yale Keyfree Connected Smart Lock using a cross head screw driver to avoid cross
threading the fixing screws. If using a cordless screwdriver, please ensure it is set to low
speed & torque.
M6: Thick & Short Screw×2
M4: Small
Screw
M4: Smallest
Screw
M6: Thick & Medium Screw×1
M5: Thin & Longest Screw×2
May be pre-assembled on main unit.
1
View
Installation
Video on
YouTube

Contents
1. Inside the Box
2. Multipoint Locking Compatibility
3. Fixing the Cylinder
4. Fitting The Spindle
5. Fitting The Handing Screw
6. Installation
7. Check Points after Installation
8. Electronically Handing the Lock
9. Troubleshooting
10. Quick Reference
1
2
3
5
6
1
1. Inside the Box
Fit the Yale Keyfree Connected Smart Lock using a cross head screw driver to avoid cross
threading the fixing screws. If using a cordless screwdriver, please ensure it is set to low
speed & torque.
M6: Thick & Short Screw×2
M4: Small
Screw
M4: Smallest
Screw
M6: Thick & Medium Screw×1
M5: Thin & Longest Screw×2
May be pre-assembled on main unit.
Keyfree
Fixing the Cylinder
Fitting the Handing Screw
Left Handed Door Right Handed Door
Before fitting Keyfree Connected, the handing screw must be fitted. Failure to so will allow the outside lever to rotate 360º.
Only use the handing screw provided which is attached to the underside of the outside lever in a bag with a yellow warning label.
Lightly tighten
the cylinder
fixing screw.
Cylinder fixing
screw
Fitting the Spindle
2
Insert the spindle
into the main unit.
After fully inserting the spindle,
push the snap fit washer down
until ‘click’ sound is heard.
Check that the spindle
freely rotates.
If the main unit includes the spindle already, please skip this step.
The keyfree handle set is only compatible with the following multipoint locks:
• Yale YS170 Range • Yale Lockmaster Range • Yale Doormaster
TM
Range
If you do not have any of the above multipoint locks the Yale Doormaster
TM
Range is designed to replace
most PVCu door locks. For more information please go to www.yale.co.uk
Multipoint Locking Compatibility
2
2.
3.
4.
5.

Installation
To avoid any possibility of being locked out, do not close
the door until a PIN code or a fob has been successfully
registered and tested to be working.
3
Check the arrow is
on the side.
M6: Thick & Short Screw
M6: Thick & Short Screw
M4: Small Screw
M6: Thick & Medium
Screw
M5: Thin & Longest
Screw
M5: Thin & Longest
Screw
Rubber Cap
*IMPORTANT*
4
Take care not to
damage spring
when fitting
inside handle
3
6.

Installation
To avoid any possibility of being locked out, do not close
the door until a PIN code or a fob has been successfully
registered and tested to be working.
3
Check the arrow is
on the side.
M6: Thick & Short Screw
M6: Thick & Short Screw
M4: Small Screw
M6: Thick & Medium
Screw
M5: Thin & Longest
Screw
M5: Thin & Longest
Screw
Rubber Cap
*IMPORTANT*
4
Take care not to
damage spring
when fitting
inside handle
4

Check Points after Installation
•Insert Remote Module (Optional)
•Insert Batteries
Take care inserting the Remote module
(optional). The pins can easily bend and
may not be replaced under warranty
Electronically Handing the Lock
•Check The Mechanical Back Up Key Works Properly
- Turn key 90 degrees.
- Press outside lever down & open door.
- Remove key
- Check the operation of the inside safety / security button handle.
The inside lever must not move unless the button is depressed.
When the inside lever returns to horizontal, the button must re-engage to prevent use.
•Check the free movement of both inside & outside levers
If the button does not re-engage, please slightly lift up the inside lever to re-engage.
5
8.
Please follow the procedure below to set the handing of the lock. Failure to do this can leave the lock
reporting it is locked when it is open and that it is unlocked when it is locked.
Step Icon Expected
Feedback
Description
Press any button Press any button on keypad to begin
Enter master code
followed by # key
2 tone beep If the master code has not been setup the
default PIN is 123456
Open the internal cover and
press the [P] button
The [P] button is above the batteries on the
back body
On the front body keypad
press the [#] key
This will put the lock into handing mode
Push the internal handle down
Lift the internal handle up
Press the [I] button, then
replace the internal cover
This will complete the lock handing.
- If you have experienced any problems while installing the Yale Keyfree Connected Smart Lock, or it
is not behaving as expected, please go to the following address on the Yale website or call the Keyfree
helpline:
-www.yale.co.uk/smart-living
Tel: [phone] Monday - Friday 8.30am - 5.30pm
Email: [email protected]
9. Troubleshooting
7
5
7.
8.
9.

10. Quick Reference
6
Change Your Master Code
Connecting to a Home Automation System
Please see page 8 in the user manual.
Registering Your Remote Fobs (Optional)
Opening and Locking Your Door
Please see page 14 in the user manual.
Please see page 19 in the user manual.
Please see page 11 in the user manual.
-
-
-
-
6

smart
Living
The smarter way to protect your home
•